user manual

ManualsBrandsZurn Industries ManualsPlumbing ProductPlumbing Product Z86300

AQUASPEC FAUCETS

MODEL - Z86300 SERIES

SINGLE BASIN METERING

TECHNICAL INFORMATION

FLOW: 0.25 GPC MAXIMUM; PRESET AT FACTORY TO 10 SECOND @ 80 PSI ADJUSTABLE

MAXIMUM PRESSURE: 125 PSI

MAXIMUM TEMPERATURE: 180

- CAN USE QUARTER TURN CERAMIC DISK CARTRIDGE

INSTALLATION INSTRUCTIONS

1. THE WATER SUPPLY LINE MUST BE THOROUGHLY FLUSHED BEFORE FAUCET INSTALLATION.

2. REMOVE FAUCET BODY FROM CARTON AND PLACE GASKET (#7A) ON SHANK.

3. PLACE FAUCET ON SINK, MOUNT LOCKWASHER (#7B) AND MOUNTING NUT (#7C) ONTO SHANK FROM UNDER SINK.

4. HAND TIGHTEN MOUNTING NUT (#7C). MAKE SURE FAUCET IS CENTERED PROPERLY. DO NOT OVER TIGHTEN, YOU

COULD DAMAGE THE FIXTURE

5. ATTACH LAVATORY SUPPLY TO THE OUTLET OF THE STOP BODY AND CONNECT TO FAUCET WITH RISER NUT

(#7D).

6. OPTIONAL - POP-UP (-P)/ GRID STRAINER (-G)/HANDICAP OFFSET GRID DRAIN (-GH):

INSTALL POP-UP OR GRID STRAINER IN SINK OUTLET AND PLUMB WASTE CONNECTION.

7. TURN SUPPLY WATER ON AND OPERATE THE FAUCET WHILE CHECKING FOR LEAKS.

8. INSTALL AERATOR (#6) INTO FAUCET AND HAND TIGHTEN.

9. METERING CARTRIDGE IS FACTORY PRESET FOR A 10 SECOND CYCLE AT 80 PSI, IF ADJUSTMENT IS

NECESSARY, SEE “ADJUSTING THE FLOW” SECTION (PAGE 2).

PAGE 1 OF 4

IMPORTANTTHE WATER SUPPLY LINES MUST BE THOROUGHLY FLUSHED BEFORE INSTALLATION TO PREVENT

FOREIGN MATTER AND DEBRIS FROM CLOGGING AND/OR DAMAGING INTERNAL COMPONENTS AND THEREBY PREVENTING

THE FAUCET FROM FUNCTIONING PROPERLY

IMPORTANTTHE FAUCET HAS AN INTEGRAL SHANK FILTER ASSEMBLY INSTALLED IN THE BODY UNDER THE METERING

CARTRIDGE TO PREVENT FOREIGN MATTER AND DEBRIS FROM DAMAGING THE FAUCET. THE INTEGRAL FILTER MAY BE

REMOVED TO BE BACK-FLUSHED AND CLEANED IF INSUFFICIENT FLOW IS DETECTED. THE INTEGRAL SHANK FILTER

ASSEMBLY MUST BE RE-INSTALLED AFTER SERVICING TO ENSURE PROPER FUNCTIONING OF THE METERING CARTRIDGE.

Form # CF848 Date: 6/19/07

C.N. No. 105794 Rev. G

Summary of content (4 pages)

PAGE 1
® AQUASPEC FAUCETS MODEL - Z86300 SERIES SINGLE BASIN METERING TECHNICAL INFORMATION FLOW: 0.
PAGE 2
MAINTENANCE 1. YOUR ZURN AQUASPEC FAUCET HAS A HIGHLY POLISHED NICKEL CHROME PLATED FINISH. CLEAN WITH SOAP AND WATER OR A MILD CLEANER WHICH IS SAFE FOR CHROME PLATING. DO NOT USE ACIDS OR TOILET BOWL CLEANER AS THEY WILL DAMAGE THE FINISH. 2. METERING CARTRIDGE (#3) REMOVAL AND REPLACEMENT 2.1. REMOVE COLORED INDEX BUTTON (#1C) FROM HANDLE (#1A) 2.2. LOOSEN SET SCREW (#1B) IN HANDLE WITH 3/32” ALLEN WRENCH 2.3. PULL UP ON HANDLE TO REMOVE FROM STEM (#2C) OF HANDLE NUT ASSEMBLY (#2) 2.4.
PAGE 3
Z86300 PICTURED ITEM 1 PART# G60522 1A 60601003 1B 62705001 1C G60558 60460001 60460002 60460003 2 G60561 2A 60465001 2B 60450001 2C 60451003 2D 60447001 2E 60446001 2F 60452001 2G 60456001 2H 62499107 2I 60458001 DESCRIPTION METERING HANDLE ASSEMBLY COLD METERING HANDLE SET SCREW METERING INDEX BUTTONS-H,C HOT INDEX COLD INDEX TEMPERED INDEX HANDLE NUT ASSEMBLY “E” RING SPRING SEAT STEM SPRING ADJUSTMENT NUT CAP STEM HOUSING O-RING O-RING RETAINER QTY ITEM 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 3A 3B 4 5
PAGE 4
Metering Faucet Trouble Shooting Guide Problem No water dispensing from faucet. Faucet is shutting off to quickly Faucet is running too long. Cause Solution Supply stops not open. Aerator contaminated. Filter assembly contaminated. Open supply stops. Remove aerator to clean and/or replace. Shut off water supply. Remove filter assembly to clean and/or replace. Filter may be located externally on supply stops, or internally within faucet body under metering cartridge.