Installation Guide

ManualsBrandsZurn ManualsBasic Kitchen Faucets2-Handle Kitchen Sink Faucet in Chrome

Form # CF1192 Date: 5/12/10

C.N. No. 126189 Rev. A

PAGE 1 OF 3

INSTALLATION INSTRUCTIONS

1. REMOVE FAUCET BODY(#6) FROM CARTON AND APPLY PLUMBERS PUTTY TO UNDERSIDE OF BODY. (REFER TO

FIGURE 1).

2. PLACE FAUCET ON SINK AND REMOVE MOUNTING NUTS (#7A) FROM BAG G60502.

3. HAND TIGHTEN MOUNTING NUTS (#7A) FROM UNDER SINK. MAKE SURE FAUCET IS CENTERED PROPERLY. DO

NOT OVER TIGHTEN.

4. OPTIONAL HOSE SPRAY (REFER TO FIGURE 2)

REMOVE HOSE SPRAY ASSEMBLY (#11) FROM PACKAGING. REMOVE MOUNTING NUT FROM HOSE SPRAY HOLDER

(#11B) AND INSERT HOSE SPRAY HOLDER THROUGH FIXTURE. ASSEMBLE MOUNTING NUT ONTO HOSE SPRAY

HOLDER AND TIGHTEN. DO NOT OVER TIGHTEN. INSERT THREADED END OF HOSE SPRAY (#11A) THROUGH HOSE

SPRAY HOLDER (#11B) AND CONNECT HOSE SPRAY (#11A) TO DIVERTER ADAPTOR (#10). TIGHTEN TO CREATE A

WATER TIGHT CONNECTION.

5. ATTACH LAVATORY SUPPLIES TO FAUCET WITH RISER NUTS (ITEM #7B).

6. OPTIONAL GRID STRAINER (-G) / HANDICAP OFFSET GRID DRAIN (-GH)

INSTALL GRID STRAINER IN SINK OUTLET AND PLUMB WASTE CONNECTION.

7. INSTALL SPOUT INTO BASE AND TIGHTEN NUT (SEE VIEWS FOR SWING/RIGID CONNECTION).

8. TURN SUPPLY WATER ON AND OPERATE FAUCET CHECKING FOR LEAKS.

9. REPLACE HANDLE SCREWS AND COLOR INDEX BUTTONS.

10. INSTALL AERATOR INTO FAUCET AND HAND TIGHTEN. IT MAY BE NECESSARY TO UNSCREW AND CLEAN AERATOR AT

START-UP.

AQUASPEC FAUCETS

MODEL - Z87100-XL SERIES

Z87100-XL-HS SERIES

KITCHEN SINK FAUCET

TECHNICAL INFORMATION

FLOW: 2.2 GPM [8.3 L] PRESSURE COMPENSATING AERATOR *

MAXIMUM PRESSURE: 125 PSI

MAXIMUM TEMPERATURE: 180

HANDLE NUT TORQUE: 15-20 FT - LBS.

CARTRIDGE STYLE: QUARTER TURN CERAMIC DISK

* OTHER AERATORS AVAILABLE BY REQUEST

ZURN INDUSTRIES, LLC

♦♦

♦ COMMERCIAL BRASS OPERATION

♦♦

♦ 2640 SOUTH WORK STREET

♦♦

♦ FALCONER NY 14733

Phone: 1-800-997-3876

♦♦

♦ Fax: 1-919-775-3541

♦♦

♦ www.zurn.com

In Canada: ZURN INDUSTRIES LIMITED

♦♦

♦ 3544 Nashua Drive

♦♦

♦ Mississauga, Ontario L4V1L2

♦♦

♦ Phone: 905/405-8272 Fax: 905/405-1292

Summary of content (3 pages)

PAGE 1
® AQUASPEC FAUCETS MODEL - Z87100-XL SERIES Z87100-XL-HS SERIES KITCHEN SINK FAUCET TECHNICAL INFORMATION FLOW: 2.2 GPM [8.3 L] PRESSURE COMPENSATING AERATOR * MAXIMUM PRESSURE: 125 PSI MAXIMUM TEMPERATURE: 180 F HANDLE NUT TORQUE: 15-20 FT - LBS. CARTRIDGE STYLE: QUARTER TURN CERAMIC DISK O * OTHER AERATORS AVAILABLE BY REQUEST INSTALLATION INSTRUCTIONS 1. REMOVE FAUCET BODY(#6) FROM CARTON AND APPLY PLUMBERS PUTTY TO UNDERSIDE OF BODY. (REFER TO FIGURE 1). 2.
PAGE 2
MAINTENANCE 1. YOUR ZURN AQUASPEC FAUCET HAS A HIGHLY POLISHED NICKEL CHROME PLATED FINISH. CLEAN WITH SOAP AND WATER OR A MILD CLEANER WHICH IS SAFE FOR CHROME PLATING. DO NOT USE ACIDS OR TOILET BOWL CLEANER AS THEY WILL DAMAGE THE FINISH. 2. AQUASPEC FAUCETS CONTAIN CERAMIC DISK CARTRIDGES WHICH REQUIRE NO MAINTENANCE. TO REMOVE THE CARTRIDGE, SHUT THE WATER OFF, LOOSEN THE HANDLE NUTS AND PULL UP ON THE CARTRIDGE.
PAGE 3
Z871B1-XL-HS PICTURED FIGURE 2 Z87100-XL-HS PARTS LIST ITEM 1 2 3 4 5 6 7 59440001 59517005 59517006 60467006 58155019 93286002 G60502 7A 59530002 7B 59532001 QTY HANDLE NUT SHORT COLD CARTRIDGE SHORT HOT CARTRIDGE BASE O-RINGS KITCHEN DECK BODY NUTS MOUNTING NUT 1/2” NPSM RISER NUT 2 1 1 1 1 1 1 2 2 ITEM 8 9 10 11 QTY 93217001 58155015 60943002 G67905 DIVERTER O-RING DIVERTER ADAPTOR HOSE ASS’Y 1 1 1 1 Form # CF1192 PAGE 3 OF 3 C.N. No. 126189 Date: Rev.