Installation Guide

ManualsBrandsZurn ManualsAccessories28 in. Stainless Steel Linear Shower Drain with Decorative Block Grate

Dimensional Data (inches and [ mm ]) are Subject to Manufacturing Tolerances and Change Without Notice

ZURN INDUSTRIES, LLC

♦♦

♦ SPECIFICATION DRAINAGE OPERATION

♦♦

♦ 1801 Pittsburgh Ave.

♦♦

♦ Erie, PA 16514

Phone: 814/455-0921

♦♦

♦ Fax: 814/454-7929

♦♦

♦ World Wide Web: www.zurn.com

In Canada: ZURN INDUSTRIES LIMITED

♦♦

♦ 3544 Nashua Drive

♦♦

♦ Mississauga, Ontario L4V1L2

♦♦

♦ Phone: 905/405-8272 Fax: 905/405-1292

Form # FT1009 Date: 06/08/12 C.N. No. 124454 Rev. - Page 1 of 6

ZS880 Linear Shower Drain

Installation Instructions

ADJUSTABLE LEG SCREW

(#6-32 X

PHMS)

#6 SS WASHER

SHOWER CHANNEL ASSEMBLY

ADJUSTABLE LEG

LEVELING SCREW

(#10-24 X

FHHSS)

TILING EDGE FRAME

FRAME SECURING SCREW

(#10-24 X

FHHSS)

GRATE

GRATE SECURING SCREW

(#6-32 X

SHCS)

Drain Components

PATENT

PENDING

Introduction

The Zurn ZS880 Stainless Steel Linear Shower Drain incorporates a simple approach to bathroom shower design, when

compared to traditional point-drain applications. The linear shower drain expands the floor surface area for water collection

and eliminates the need for multiple slope construction of the floor. When handling and installing the ZS880 linear drain,

please pay close attention to the following guidelines and warnings:

• Please handle all stainless steel material with caution. The manufacturing process used in making this

product can inadvertently produce sharp edges, which may result in injury if handled or used improperly.

• Please adhere to all torque specification requirements outlined within these instructions when tightening

hardware during installation.

• Do not apply corrosive chemicals to this product which may alter the appearance and surface finish.

• All grating provided with this product is rated for light-duty applications, per ASME Standard A112.6.3

specifications.

Summary of content (6 pages)

PAGE 1
ZS880 Linear Shower Drain Installation Instructions ® Dimensional Data (inches and [ mm ]) are Subject to Manufacturing Tolerances and Change Without Notice PATENT PENDING Introduction The Zurn ZS880 Stainless Steel Linear Shower Drain incorporates a simple approach to bathroom shower design, when compared to traditional point-drain applications. The linear shower drain expands the floor surface area for water collection and eliminates the need for multiple slope construction of the floor.
PAGE 2
® ZS880 Linear Shower Drain Installation Instructions Dimensional Data (inches and [ mm ]) are Subject to Manufacturing Tolerances and Change Without Notice Adjusting the Anchoring Legs Each shower drain is provided standard with two preassembled anchoring legs, one on each end of the channel. The anchoring legs help hold the channel in place and adjust it to an appropriate height, prior to construction of the subfloor.
PAGE 3
® ZS880 Linear Shower Drain Installation Instructions Dimensional Data (inches and [ mm ]) are Subject to Manufacturing Tolerances and Change Without Notice Adjusting the Tiling Frame Each shower drain is provided with a series of #10-24 x 7/8 flat head hex socket screws that thread into sealed blind-hole inserts, which are crimped to the shower channel. The screws have dual functions within the shower drain assembly: 1.
PAGE 4
ZS880 Linear Shower Drain Installation Instructions ® Dimensional Data (inches and [ mm ]) are Subject to Manufacturing Tolerances and Change Without Notice Adjusting the Tiling Frame (cont’d): STEP 11: When the frame is set at the required position, secure the frame to the shower channel by tightening the frame screws. To prevent damage to the frame, DO NOT over-tighten the securing screws. The frame should now be locked in place and ready for tiling.
PAGE 5
ZS880 Linear Shower Drain Installation Instructions ® Dimensional Data (inches and [ mm ]) are Subject to Manufacturing Tolerances and Change Without Notice Typical Installation Drawing TILE WATERPROOFING MEMBRANE ADJUSTABLE TILING EDGE FRAME THINSET ADJUSTABLE LEG THINSET/ADHESIVE SUBFLOOR TILING FRAME GROUT TILE WATERPROOF MEMBRANE THINSET CONCRETE SUBFLOOR THINSET/ ADHESIVE FRAME LEVELING SCREWS DRAIN OUTLET Form # FT1009 Date: 06/08/12 C.N. No. 124454 Rev.
PAGE 6
® ZS880 Linear Shower Drain Installation Instructions Dimensional Data (inches and [ mm ]) are Subject to Manufacturing Tolerances and Change Without Notice Typical Drain Placement in Bathroom Floor Construction ENTRANCE ENTRANCE Back of the Shower Location Entrance Way (Curb or Curbless) ENTRANCE ENTRANCE Multi-Unit Shower Room Form # FT1009 Date: 06/08/12 C.N. No. 124454 Rev. - Page 6 of 6 ZURN INDUSTRIES, LLC ♦ SPECIFICATION DRAINAGE OPERATION ♦ 1801 Pittsburgh Ave.