Installation guide

ManualsBrandsZuvo ManualsHousehold Appliances150 Series

Page 1

Zuvo Water Filtration System

Zuvo Beverage Faucet

(type and nish may vary)

Spout

1/4 C x 1/4 MIP adapter

On/O lever

Faucet body

Chrome washer

Rubber gasket

Clamp washer

Nut

Wall mount bracket

(mount vertically only)

3/8" Supply EZ

angle stop adapter

3/8" Supply

compression adapter

1/2" Pipe tap with

rubber seals

Teon tape

Mounting screw (2)

Zuvo Water

Filtration System

Unpack all pieces and insure that you have all components listed below. If any parts are missing contact

Zuvo Water or your Zuvo Water dealer.

The Zuvo™ Water Filtration System is designed to connect to a separate, dedicated Zuvo Beverage Faucet

mounted on your sink top. Installation is straightforward and most “do-it-yourself” types will nd it relatively

easy. If you are uncomfortable working with or around plumbing, enlist the help of a licensed plumber.

Prior to installing

the Zuvo Water

Filtration System,

record the serial

number located

on the lower back

of the unit.

Installation Guide

1. UNPACKING AND INSPECTION

Figure 1

Summary of content (8 pages)

PAGE 1
Prior to installing the Zuvo Water Filtration System, record the serial number located on the lower back of the unit. Zuvo Water Filtration System Installation Guide The Zuvo™ Water Filtration System is designed to connect to a separate, dedicated Zuvo Beverage Faucet mounted on your sink top. Installation is straightforward and most “do-it-yourself” types will find it relatively easy. If you are uncomfortable working with or around plumbing, enlist the help of a licensed plumber. 1.
PAGE 2
Zuvo Water Filtration System Installation Components Item Purpose Zuvo Water Filtration System Zuvo Water Filtration System Above sink, dedicated faucet for dispensing water treated with the Zuvo Water Filtration System. RED, WHITE/YELLOW, and BLUE tubing Zuvo Beverage Faucet Assembly Actual appearance varies by faucet type and finish WARNING: Do not use any faucet other than the one supplied by Zuvo Water. Failure to follow these instructions may void your warranty and/or damage your Zuvo unit.
PAGE 3
. ZUVO WATER FILTRATION SYSTEM INSTALLATION INSTRUCTIONS Prior to installing the Zuvo Beverage Faucet, select a suitable under-counter location for mounting or placing your Zuvo unit. The Zuvo unit should be mounted/located no more than about 3 feet from beneath the Zuvo Beverage Faucet. NOTE: If you do not have a Ground Fault Circuit Interrupter (GFCI) and outlet that is not controlled by a switch under your sink, consult an electrician.
PAGE 4
When drilling a new hole, ensure you have proper clearance beneath your sink (for the attachment of retaining nut, etc.). Make sure that the under-counter location you have selected for your Zuvo Water Filtration System is within 3 feet of the Zuvo Beverage Faucet. Insert the Zuvo Beverage Faucet spout into the faucet body. Unscrew and remove the nut and slotted washer from the faucet assembly. Leave the decorative chrome washer and rubber gasket on the stem of the faucet assembly.
PAGE 5
. 1/2" PIPE TAP OR 3/8" SUPPLY COMPRESSION ADAPTOR Turn off cold water supply shutoff valve Cold water supply Turn off the cold water supply by turning the shut off valve handle all the way to the right. Test your faucet to ensure there is no cold water flow. Place a bucket or pan on the floor under the cold water supply in the event that a small amount of water drains down from the sink.
PAGE 6
Cold water supply Reconnect the flexible hose to the 1/2" pipe tap or the 3/8" supply adapter. Use adjustable wrench to tighten nut securely. Figure 10 Cold water supply Using scissors, trim the RED tubing, coming from the Zuvo Beverage Faucet, to the desired length AVOID CUTTING THE TUBE TOO SHORT! Insert the RED tubing into the 1/4" MIP adapter or 1/4" side outlet on the EZ adapter until fully seated. Figure 11 Pull RED tubing firmly to ensure that tubing does not come free. 6.
PAGE 7
Simply connect the WHITE/YELLOW tube from the faucet to the WHITE/YELLOW tube conector on the Zuvo Water Filtration System as shown in Figure 13. Similarly, connect the BLUE tube from the faucet to the BLUE tube on the Zuvo unit. Ensure both tubes are inserted into the connectors until they stop and cannot be pushed in further. Figure 13 Pull on tubes to be sure they are seated properly Firmly pull on WHITE/ YELLOW and BLUE tubing to ensure that they are tightly held in the compression fittings.
PAGE 8
7. PLUMBING CHECKOUT Open the cold water shutoff valve and visually verify that no water is leaking from around the threads of the 1/2" pipe tap, the 3/8" supply adapter or the 1/4" compression adapter and RED tubing. After you are certain there are no leaks, fix the position of the Zuvo Beverage Faucet by tightening the hex nut at the bottom. 8. SYSTEM CHECKOUT Ensure that the Zuvo Water Filtration System is plugged into an electrical outlet.