Quick Setup Guide
a
Alternative Ways To Connect The AV120 TV Speaker
If your TV doesn’t have an optical audio output, here are some other options:
(TV Port Example)
AUDIO OUT
HP
X
PC
IN
DC IN
Optical
Line In
USB
R L
R L
X
RCA jacks
labeled
“AUDIO OUT”
Other
RCA jacks
(usually audio IN)
DC IN
Optical
Line In
USB
b
Back of TV
Minijack Analog Audio Out
Some TVs have a 3.5mm audio output jack or a headphone
jack. Insert one end of the supplied analog “Miniplug to
Miniplug” cable into the TV’s audio out miniack. Insert the
miniplug at the other end of the cable into the ZVOX speaker’s
rear input jack labeled OPTICAL LINE IN. This port also
supports analog connections.
If the TV has a headphone jack, you will want to make sure
that the TV’s volume is turned up to 50 to 75 % of maximum
volume to make sure that the ZVOX speaker is receiving a
strong audio signal to amplify.
Red and White RCA Jack Analog Audio Out
Some TV models use red and white RCA jacks for the analog audio
output. Be sure you have located red and white jacks on the TV that
are marked as an “OUTPUT” (not “INPUT”). Next, identify the cable
supplied with the ZVOX speaker that has a stereo miniplug at one
end and red and white RCA plugs at the other end.
Make The Connection
Insert the end of the cable with red and white plugs into the red
and white jacks on the TV labeled “OUT”. Insert the miniplug at the
other end of the cable into the ZVOX speaker input jack labeled
OPTICAL LINE IN.
Cable In
Network
USB
HDMI
To T V
Power
L
R
Analog
Audio
Cable/Satellite Set Top Box (Example)
Lorem ipsum
Digital
Audio
Connect To Your Cable Or
Satellite TV Set Top Box
If your TV’s audio output is inaccessible (on a wall-mounted TV,
for instance) or unavailable, you can connect the audio output of
your cable or satellite set top box to the ZVOX speaker. Most set
top boxes have an “audio output” in addition to the HDMI output
intended for use with the TV.
To connect between the set top box red and white jacks and the
ZVOX speaker, identify the cable supplied with the ZVOX speaker
that has a stereo miniplug at one end and red and white RCA
plugs at the other end.
Follow the “Make The Connection” instructions in the
previous column.
c
Back of
Cable/Sat Set Top Box
Back of TV
2 ZVOX AV120 | Connect AV120
Placing The AV120 TV Speaker in
Front of the TV.
Most people choose to place the ZVOX speaker in front of the TV.
But it can also be placed on any level surface near the TV – above,
below or to the left or right. Choose a place that lets you direct the
ZVOX Speaker towards the TV viewers.
• A safe, secure installation of the AccuVoice TV Speaker is the
owner’s responsibility.
• Do not place any objects on top of the AccuVoice
TV Speaker.
Placement Options
TV to AV120 Audio Signal
Cable Guide
The AV120 includes two analog signal cables and one optical
digital signal cable. The optical cable has a standard optical plug
on one end and a mini optical plug on the other end. One of these
three cables will connect from most TVs or cable/satellite set top
boxes to the input on the AV120. In the rare instance your TV
or cable/satellite set top box has only an optical minijack audio
output, an optical miniplug to optical miniplug cable is needed
(not supplied with the AV120).
Audio cables supplied with the ZVOX TV Speaker
standard optical plug
to
analog miniplug
analog miniplug
to
analog miniplug
red and white
RCA plugs
to analog miniplug
DC IN
Optical
Line In
USB
USB Input
Insert an external USB ash drive to hear audio tracks, like
MP3s play externally from the AV120. Use the BACK and FWD
buttons on the AV120 remote to toggle back and forward to
audio tracks on your USB Drive. MP3 Files may be in the root
or in folders.
USB Flash Drive
Bluetooth setting.
You may play audio from your Smart phone, tablet, laptop or
Bluetooth capable TV to the AV120 as well.
Simply press the INPUT button on the AV120 remote until the
AV120 display on the front of the speaker blinks blue which
signals the sound bar is in pairing mode. It will stay solid blue
once paired with device.
Manual On/Off Operation
With the unit on, press and hold the “Other Settings” button for
5 seconds. If the LED blinks RED 3X, the auto On/Off feature is
disabled.
The remote must be used to turn the unit on and off.
If the LED blinks BLUE 3X, the auto On/Off feature is being re-
enabled. The Auto On/Off toggle only works if the minijack input
is selected. It will automatically turn off 30 seconds after a loss
of digital signal OR several minutes after an analog signal has
stopped.
ZVOX AV120 | Cables and Placement 3
Power
The Power button switches the ZVOX speaker between off (STANDBY)
and on. When the ZVOX AV120 is powered on, you will see a white light
follwed by a green light behind the front speaker grille ash. When it is
powered off into STANDBY, you will see the red light ash four times. Any
button press from the ZVOX remote will also power on the system.
Note: The ZVOX AV120 will also enter STANDBY if it receives no audio
signal for several minutes.
Button Functions on the ZVOX Remote Control
BACK
MUTE
PLAY/PAUSE
OTHER
SETTINGS
VOLUME
ACCUVOICE SURROUND
FWD
INPUT
POWER
Volume
When the volume up arrow button is quickly pressed and released,
you will see the light corresponding to your input (Green, Blue, Red)
ash indicating one volume step increase. If you press and hold down
the volume up button, the light will continuously ash and the volume
will go up until you release the button. The volume down arrow button
is indicated by the yellow light and ashes in the same manner when
pressed and released.
Mute Play/Pause
Press this button to mute the ZVOX speaker. When the MUTE function
is active, the display blinks yellow repeatedly. The AV120 will enter
STANDBY if it is left in MUTE for longer than 5 minutes. The button also
doubles as the Play/Pause function when using sound bar with the USB
Drive and/or the Bluetooth
AccuVoice
Press the AccuVoice button to select the AccuVoice function. Additional
presses of the AccuVoice button allow you to select increasing
levels of voice enhancement. There are two levels of increasing voice
enhancement, starting with AccuVoice 1 going to 2. The light ashes
purple a certain number of times to indicate which AccuVoice mode you
are selecting. The default setting is AccuVoice 1. If you were to press
the AccuVoice button once you would see the light blink twice indicat-
ing AccuVoice 2 mode. Once you are in AccuVoice 2 mode, pressing
the AccuVoice button will return you to AccuVoice 1.
Back and Forward
The Back and Forward buttons will allow you skip forward, or back,
from audio tracks when using the USB Drive Input or Bluetooth
connections.
Other Settings
The OTHER SETTINGS button can be used to control the Auto on/off
feature when the minijack input is selected OR to cancel a bluetooth
connection and start the pairing process when the Bluetooth input is
selected.
Input Selection
Press the INPUT button on the ZVOX remote to select between
the speaker’s input modes. Note: The USB input is not selectable
unless a USB thumb drive is plugged in.
Surround Settings
There are two SURROUND levels: Surround One has low virtual surround
effect and strong vocals. Use this setting if vocal clarity is important to you.
Surround Two has moderate virtual surround effect and moderate vocals.
The default setting is Surround 1. If you were to press this button again you
would see the Pale Blue light blink twice indicating Surround 2 mode.
4 ZVOX AV120 | Remote Control
STILL NEED ASSISTANCE? If your TV is not the same as the
descriptions in this guide, don’t hesitate to send an inquiry to
info@zvoxaudio.com or call ZVOX Audio at (866) 367-9869. Please
provide your TV brand and model number. For information about
additional options, please refer to the ZVOX Audio website, www.zvox.
com.
USA Warranty
For warranty information applicable to an AV120, please visit this webpage:
https://zvox.com/pages/warranty-returns
4020X 5/22
www.zvox.com
© 2022 ZVOX Audio LLC. ® ZVOX, AccuVoice and PhaseCue
are registered trademarks of ZVOX Audio LLC.
240 mm
650 mm
反面
展开尺寸：650x240mm,风琴4折页，折后尺寸：240x130mm
材质：80G书纸，双面单黑印刷