Quick Installation Guide

C. Installing the device mounting bracket
The device package includes a stainless steel mounting bracket that MUST be
used for installation. Please note the mounting bracket in the box is designed for
the US standard 2-gang and supplied Arlington mounting ring supplied in the box.
You can order additional stainless steel mounting brackets for UK or European
electrical boxes. Verify that the bracket is level before tightening the captive screws
on the device. (US mounting bracket included in the box)
Thank you for including the device as part of the user interface strategy for your
customer. The device has been designed to provide years of trouble free
operation when wired and installed properly. The device is designed for
installation in low humidity indoor environments and should never be installed
outdoors or in high humidity areas.
E. Mounting the device
Loosen the captive screws of the unit first. Screws should not be moved
apart from the unit. Please meet the indicated line. Align the mounting frame
hooks with the mounting slots and gently pull the unit down the mounting
bracket. Make sure the mounting hooks are properly engaged. To complete
the installation, tighten the 2-captive screws on the bottom part of unit, to
secure the device on the mounting bracket.
Loosen
D. Connecting the device to power
The device is designed to be powered over the Ethernet connection (PoE) or
by connecting a 24Vdc power supply (not included), but not both. If both the
PoE and a 24Vdc power supply are connected, the device will draw power
from the 24V source.
PoE Connection
PoE connection requires IEEE 802.3af standard. Utilize a network switch or
PoE injector that meets this standard. Connect the device using a standard
T568A or T568B Ethernet cable from the network switch to the LAN/PoE
jack on the back of the device.
24Vdc Power Supply
You can provide power locally or remotely to device by utilizing a 24V DC
power supply (not included). Please note that running the wire through the
wall in accordance with local codes when powering locally. If powering
remotely, please ensure to use wire of adequate gauge for the length of the
run. Please use approved 24V DC power supply.
Verify the polarity of the barrel connector on your power supply before
connecting it to the device. The center pin of the device power connector is
positive and the outer ring is negative. If the wire is extended, please ensure
that the routing is in compliance with local codes.
Plug the connector into the device DC jack on the back of the device.
Network Switch
PoE Injector
To device
PoE Network Switch
Removing the device
Using a precision Philips head screw driver to loosen the 2-captive screws on
the device, then slightly pull straight up from the mounting frame to disengage
the unit.
Sonata XL
English V1.0
Consult the dealer or contact [e-mail] for help
On European 1-gang
electrical box
On UK standard 1-gang
electrical box
On standard NEMA 1-gang
US electrical junction box
On low-voltage mounting
ring-like Arlington LV1
Line in wall
24V DC
2.1mm
Coaxial Plug
Tighten
CAUTION: DO NOT PRESS DIRECTLY ON THE SCREEN
when installing on to the mounting bracket.
Press only on the frame edges.
Tighten
Top of single-gang Box
Mounting Bracket
Dry Wall
1
2
3
1
2
3
Push
Draw out
Powering up the device
The device will automatically power
on when power is applied. Wait for the
unit to boot up. When it's connected to
a network switch by Ethernet cable, the
device will acquire a network address via
DHCP and automatically connect to the system.
Temperature ranges/humidity
±0 °C to +45 °C
−20 °C to +70 °C
max. 95%(no condensation)
Operating
Storage/transport
Relative humidity
Any changes or modifications not expressly approved by the grantee of this device could
void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
RF exposure warning
This equipment must be installed and operated in accordance with provided instructions and
the antenna(s) used for this transmitter must be installed to provide a separation distance of
at least 20 cm from all persons and must not be co-located or operating in conjunction with
any other antenna or transmitter. End-users and installers must be provide with antenna
installation instructions and transmitter operating conditions for satisfying RF exposure
compliance.
Canada, Industry Canada (IC) Notices
This device complies with Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Canada, avis d'Industry Canada (IC)
Cet appareil est conforme avec Industrie Canada exemptes de licence RSS standard(s).
Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas
causer d'interférence et (2) cet appareil doit accepter toute interférence, notamment les
interférences qui peuvent affecter son fonctionnement.