Quick Installation Guide

C. Installing the device mounting bracket
The device package includes a stainless steel mounting bracket that MUST be
used for installation. Please note the mounting bracket in the box is designed for
the US standard 2-gang and supplied Arlington mounting ring supplied in the box.
You can order additional stainless steel mounting brackets for UK or European
electrical boxes. Verify that the bracket is level before tightening the captive screws
on the device. (US mounting bracket included in the box)
Setting screen orientation
On the touch panel setup screen, select Landscape or Portrait display modes.
Press Start device to launch the user interface.
To change orientation:
- Remove power from device.
- Re-apply power to device.
- Select landscape or portrait orientation.
Thank you for including the device as part of the user interface strategy for your
customer. The device has been designed to provide years of trouble free
operation when wired and installed properly. The device is designed for
installation in low humidity indoor environments and should never be installed
outdoors or in high humidity areas.
E. Mounting the device
1. Loosen the captive screws of the unit first. Screws should not be moved
apart from the unit. Please meet the indicated line.
2. Align the mounting frame hooks with the mounting slots and gently pull
the unit down the mounting bracket. Make sure the mounting hooks are
properly engaged.
3. To complete the installation, tighten the 2-captive screws on the bottom
part of unit, to secure the device on the mounting bracket.
4. For Portrait orientation, rotate mounting bracket and 90 degrees in
counterclockwise direction before installation.
Line in wall
24V DC
2.1mm
Coaxial Plug
Loosen
D. Connecting the device to power
The device is designed to be powered over the Ethernet connection (PoE) or
by connecting a 24Vdc power supply (not included), but not both. If both the
PoE and a 24Vdc power supply are connected, the device will draw power
from the 24V DC source.
PoE Connection
PoE connection requires IEEE 802.3af standard. Utilize a network switch or
PoE injector that meets this standard. Connect the device using a standard
T568A or T568B Ethernet cable from the network switch to the LAN/PoE
jack on the back of the device.
24V DC Power Supply
You can provide power locally or remotely to device by utilizing a 24V DC
power supply (not included). Please note that running the wire through the
wall in accordance with local codes when powering locally. If powering
remotely, please ensure to use wire of adequate gauge for the length of the
run. Please use approved 24V DC power supply.
Verify the polarity of the barrel connector on your power supply before
connecting it to the device. The center pin of the device power connector is
positive and the outer ring is negative. If the wire is extended, please ensure
that the routing is in compliance with local codes.
Plug the connector into the device DC jack on the back of the device.
Network Switch
PoE Injector
To device
PoE Network Switch
Removing the device
Using a precision Philips head screw driver to loosen the 2-captive screws on
the device, then slightly pull straight up from the mounting frame to disengage
the unit.
Loosen
Tighten the 2-captive screws to secure
the device to the mounting bracket.
Tighten
Melody II
English V1.1
Consult the dealer or contact [e-mail] for help
For standard NEMA 2-gang
US electrical junction box
Part No.:80-128-1210-21
For low-voltage mounting ring-like
Arlington LV2 (Supplied in the box)
Part No.:80-128-1210-21
For UK standard 2-gang
electrical box
Part No.:84-128-1230-00
For European/Italian
16204 muiltibox
Part No.:84-128-1220-00
Powering up the device
The device will automatically power
on when power is applied. Wait for the
unit to boot up. When it's connected to
a network switch by Ethernet cable, the
device will acquire a network address via DHCP
and automatically connect to the system.
Temperature ranges/humidity
±0 °C to +45 °C
−20 °C to +70 °C
max. 95%(no condensation)
Operating
Storage/transport
Relative humidity
Any changes or modifications not expressly approved by the grantee of this device could
void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
RF exposure warning
This equipment must be installed and operated in accordance with provided instructions and
the antenna(s) used for this transmitter must be installed to provide a separation distance of
at least 20 cm from all persons and must not be co-located or operating in conjunction with
any other antenna or transmitter. End-users and installers must be provide with antenna
installation instructions and transmitter operating conditions for satisfying RF exposure
compliance.
Canada, Industry Canada (IC) Notices
This device complies with Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Canada, avis d'Industry Canada (IC)
Cet appareil est conforme avec Industrie Canada exemptes de licence RSS standard(s).
Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas
causer d'interférence et (2) cet appareil doit accepter toute interférence, notamment les
interférences qui peuvent affecter son fonctionnement.