User's Manual
Table Of Contents
- Contents Overview
- Table of Contents
- Introduction
- Introducing the Web Configurator
- Internet / Wireless Setup Wizard
- Tutorials
- 4.1 Overview
- 4.2 Setting Up Your DSL Connection
- 4.3 IPv6 Address Configuration
- 4.4 Setting Up a Secure Wireless Network
- 4.5 Configuring the MAC Address Filter for Restricting Wireless Internet Access
- 4.6 Setting Up NAT Forwarding for a Game Server
- 4.7 Configuring Firewall Rules to Allow a Specified Service
- 4.8 Configuring Static Route for Routing to Another Network
- 4.9 Port Binding Configuration
- 4.10 Configuring QoS to Prioritize Traffic
- 4.11 Access the AMG1302/AMG1202-TSeries from the Internet Using DDNS
- Connection Status and System Info Screens
- Broadband
- Wireless LAN
- Home Networking
- Static Route
- Quality of Service (QoS)
- Network Address Translation (NAT)
- Port Binding
Chapter 8 Home Networking
AMG1302/AMG1202-TSeries User’s Guide
130
Router Lifetime Enter the time in seconds that hosts should consider the AMG1302/AMG1202-TSeries
to be the default router. Possible values for this field are 0-9000.
Router Preference Select the router preference (Low, Medium or High) for the AMG1302/AMG1202-
TSeries. The AMG1302/AMG1202-TSeries sends this preference in the router
advertisements to tell hosts what preference they should use for the AMG1302/
AMG1202-TSeries. This helps hosts to choose their default router especially when
there are multiple IPv6 router in the network.
Note: Make sure the hosts also support router preference to make this function work.
Reachable Time (ms) Enter the time in milliseconds that can elapse before a neighbor is detected. Possible
values for this field are 0-3600000.
Retrans Timer (ms) Enter the time in milliseconds between neighbor solicitation packet retransmissions.
Possible values for this field are 1000-4294967295.
RA Interval Enter the time in seconds between router advertisement messages. Possible values for
this field are 4-1800.
Delegate MTU from
WAN
Select this to have the AMG1302/AMG1202-TSeries obtain the MTU setting from the
service provider or uplink router.
Manual Select this to specify the MTU manually.
MTU The Maximum Transmission Unit. Type the maximum size of each IPv6 data packet, in
bytes, that can move through this interface. If a larger packet arrives, the AMG1302/
AMG1202-TSeries divides it into smaller fragments.
DAD attempts Specify the number of DAD (Duplicate Address Detection) attempts before an IPv6
address is assigned to the AMG1302/AMG1202-TSeries LAN interface. Possible values
for this field are 1-7.
DHCPv6
DHCPv6 Server Use this field to Enable or Disable DHCPv6 server on the AMG1302/AMG1202-
TSeries.
DNSv6 Mode Select the DNS role (Proxy or Relay) that you want the AMG1302/AMG1202-TSeries
to act in the IPv6 LAN network. Alternatively, select Manual and specify the DNS
servers’ IPv6 address in the fields below.
Primary DNS This field is available if you choose Manual as the DNSv6 mode. Enter the first DNS
server IPv6 address the AMG1302/AMG1202-TSeries passes to the DHCP clients.
Secondary DNS This field is available if you choose Manual as the DNSv6 mode. Enter the second DNS
server IPv6 address the AMG1302/AMG1202-TSeries passes to the DHCP clients.
Information refresh
time
Enter the number of seconds a DHCPv6 client should wait before refreshing
information retrieved from DHCPv6.
Apply Click this to save your changes.
Cancel Click this to restore your previously saved settings.
LABEL DESCRIPTION