User's Manual
Table Of Contents
- Contents Overview
- Table of Contents
- Introduction
- Introducing the Web Configurator
- Internet / Wireless Setup Wizard
- Tutorials
- 4.1 Overview
- 4.2 Setting Up Your DSL Connection
- 4.3 IPv6 Address Configuration
- 4.4 Setting Up a Secure Wireless Network
- 4.5 Configuring the MAC Address Filter for Restricting Wireless Internet Access
- 4.6 Setting Up NAT Forwarding for a Game Server
- 4.7 Configuring Firewall Rules to Allow a Specified Service
- 4.8 Configuring Static Route for Routing to Another Network
- 4.9 Port Binding Configuration
- 4.10 Configuring QoS to Prioritize Traffic
- 4.11 Access the AMG1302/AMG1202-TSeries from the Internet Using DDNS
- Connection Status and System Info Screens
- Broadband
- Wireless LAN
- Home Networking
- Static Route
- Quality of Service (QoS)
- Network Address Translation (NAT)
- Port Binding
Chapter 10 Quality of Service (QoS)
AMG1302/AMG1202-TSeries User’s Guide
146
Mac Netmask Type the mask for the specified MAC address to determine which bits a packet’s MAC
address should match.
Enter “f” for each bit of the specified source MAC address that the traffic’s MAC address
should match. Enter “0” for the bit(s) of the matched traffic’s MAC address, which can be
of any hexadecimal character(s). For example, if you set the MAC address to
00:13:49:00:00:00 and the mask to ff:ff:ff:00:00:00, a packet with a MAC address of
00:13:49:12:34:56 matches this criteria.
Exclude Select this option to exclude the packets that match the specified criteria from this
classifier.
Others
IP Protocol This field is available only when you select IPv4 or IPv6 in the Ether Type field.
If you select IPv4, select this option and select the protocol (service type) from TCP/
UDP, TCP, UDP or ICMP.If you select IPv6, select this option and select the protocol
(service type) from TCP/UDP, TCP, UDP or ICMPv6.
TCP ACK This field is available only when you select TCP in the IP protocol field.
If you select this option, the matched TCP packets must contain the ACK (Acknowledge)
flag.
Packet Length This field is available only when you select IPv4 or IPv6 in the Ether Type field.
Select this option and enter the minimum and maximum packet length (from 46 to 1500)
in the fields provided.
IPP/DS Field Select IPP/TOS to specify an IP precedence range and type of services.
Select DSCP to specify a DiffServ Code Point (DSCP) range.
IP Precedence
Range
Enter a range from 0 to 7 for IP precedence. 0 is the lowest priority and 7 is the highest.
Type of
Service
Select a type of service from the drop-down list box.
Available options are: Normal service, Minimize delay, Maximize throughput,
Maximize reliability and Minimize monetary cost.
DSCP Range Select this option and specify a DSCP (DiffServ Code Point) number between 0 and 63 in
the field provided.
802.1P Select this option and select a priority level (between 0 and 7) from the drop-down list
box.
"0" is the lowest priority level and "7" is the highest.
VLAN ID Select this option and enter the source VLAN ID in this field.
Exclude Select this option to exclude the packets that match the specified criteria from this
classifier.
Action
Forward To Select the interface through which traffic that matches the rule is forwarded out. If you
select Unchange, the AMG1302/AMG1202-TSeries forwards traffic of this class according
to the default routing table.
If traffic of this class comes from a WAN interface and is in a queue that forwards traffic
through the LAN/WLAN interface, the AMG1302/AMG1202-TSeries ignores the setting
here.
IPP/DS Field Select IPP/TOS to specify an IP precedence range and type of services.
Select DSCP to specify a DiffServ Code Point (DSCP) range.
Table 44 QoS > Class Setup Add/Edit (continued)
LABEL DESCRIPTION