User's Manual

ManualsBrandsZyXEL Communications ManualsComputers & AccessoriesWLAN USB Adapter

Table Of Contents

User’s Guide
Copyright
Federal Communications Commission (FCC) Interference Statement
ZyXEL Limited Warranty
Customer Support
Table of Contents
List of Figures
List of Tables
Preface
1. Getting Started
- 1.1.1 Application Overview
- 1.2 ZyXEL G-220 v2 Hardware and Utility Installation
- 1.4 Windows XP Users Only
  - 1.6.1 Site Survey
  - 1.7.1 Change ZyXEL G-220 v2 Mode
2. Wireless LAN Network
- 2.1.1 SSID
- 2.1.2 Channel
- 2.1.3 Transmission Rate (Tx Rate)
- 2.2.1 Data Encryption with WEP
- 2.2.2 IEEE 802.1x
  - 2.2.2.1 EAP Authentication
- 2.2.3 WPA(2)
  - 2.2.3.1 Encryption
  - 2.2.3.2 User Authentication
- 2.2.4 WPA(2)-PSK Application Example
- 2.2.5 WPA(2) with RADIUS Application Example
- 2.3 Encryption Type
- 2.4 Preamble Type
3. Wireless Station Mode Configuration
- 3.2 The Link Info Screen
  - 3.2.1 Trend Chart
- 3.3 The Site Survey Screen
- 3.4 The Profile Screen
  - 3.4.1 Adding a New Profile
- 3.5 The Adapter Screen
4. Access Point Mode Configuration
- 4.1.1 Additional Setup Requirements
- 4.2 The Link Info Screen
- 4.3 The Configuration Screen
- 4.4 The MAC Filter Screen
5. Maintenance
6. Troubleshooting
- 6.1 Problems Starting the ZyXEL Utility Program
- 6.2 Problem Connecting to an Access Point
- 6.3 Problem with the Link Status
- 6.4 Problems Communicating With Other Computers
A. Product Specifications
B. Access Point Mode Setup Example
- Configuring the Computer on Which You Install the ZyXEL G- 220 v2
- Configuring the Wireless Station Computer
C. Disable Windows XP Wireless LAN Configuration Tool
- Via the Wireless Network System Tray Icon
- Via the Control Panel
D. Management with Wireless Zero Configuration
- Activating Wireless Zero Configuration
- Connecting to a Wireless Network
- Security Settings
- Association
- Authentication
- Ordering the Preferred Networks
E. Types of EAP Authentication
- EAP-MD5 (Message-Digest Algorithm 5)
- EAP-TLS (Transport Layer Security)
- EAP-TTLS (Tunneled Transport Layer Service)
- PEAP (Protected EAP)
- LEAP
- Dynamic WEP Key Exchange
- WPA(2)
- Encryption
- User Authentication
- WPA(2)-PSK Application Example
- WPA(2) with RADIUS Application Example
- Security Parameters Summary
F. Setting up Your Computer’s IP Address
- Windows 95/98/Me
- Installing Components
- Configuring
- Verifying Settings
- Windows 2000/NT/XP
- Verifying Settings
- Macintosh OS 8/9
- Verifying Settings
- Macintosh OS X
- Verifying Settings
Index
- A
- C
- D
- E
- F
- G
- H
- I
- L
- M
- N
- O
- P
- Q
- R
- S
- T
- U
- V
- W
- Z

ZyXEL G-220 v2 User’s Guide

50 Chapter 3 Wireless Station Mode Configuration

Figure 27 Station Mode: Profile: Activate the Profile

3.5 The Adapter Screen

To set the advanced features on the ZyXEL G-220 v2, click the Adapter tab.

Figure 28 Station Mode: Adapter

The following table describes the labels in this screen.

Table 14 Station Mode: Adapter

LABEL DESCRIPTION

Adapter Setting

Transmission Rate Select a transmission speed from the drop-down list box. Choose from Fully Auto

(default), 1 Mbps, 2 Mbps, 5.5 Mbps, 6 Mbps, 9 Mbps, 11 Mbps, 12 Mbps, 18

Mbps, 24 Mbps, 36 Mbps, 48 Mbps, and 54 Mbps.

Preamble Type Select a preamble type. Choices are Long, Short and Auto.The default setting is

Auto.

Refer to Section 2.4 on page 31 for more information