User's Manual

ManualsBrandsZyXEL Communications ManualsComputers & AccessoriesWLAN USB Adapter

100

Table Of Contents

User’s Guide
Copyright
Federal Communications Commission (FCC) Interference Statement
ZyXEL Limited Warranty
Customer Support
Table of Contents
List of Figures
List of Tables
Preface
1. Getting Started
- 1.1.1 Application Overview
- 1.2 ZyXEL G-220 v2 Hardware and Utility Installation
- 1.4 Windows XP Users Only
  - 1.6.1 Site Survey
  - 1.7.1 Change ZyXEL G-220 v2 Mode
2. Wireless LAN Network
- 2.1.1 SSID
- 2.1.2 Channel
- 2.1.3 Transmission Rate (Tx Rate)
- 2.2.1 Data Encryption with WEP
- 2.2.2 IEEE 802.1x
  - 2.2.2.1 EAP Authentication
- 2.2.3 WPA(2)
  - 2.2.3.1 Encryption
  - 2.2.3.2 User Authentication
- 2.2.4 WPA(2)-PSK Application Example
- 2.2.5 WPA(2) with RADIUS Application Example
- 2.3 Encryption Type
- 2.4 Preamble Type
3. Wireless Station Mode Configuration
- 3.2 The Link Info Screen
  - 3.2.1 Trend Chart
- 3.3 The Site Survey Screen
- 3.4 The Profile Screen
  - 3.4.1 Adding a New Profile
- 3.5 The Adapter Screen
4. Access Point Mode Configuration
- 4.1.1 Additional Setup Requirements
- 4.2 The Link Info Screen
- 4.3 The Configuration Screen
- 4.4 The MAC Filter Screen
5. Maintenance
6. Troubleshooting
- 6.1 Problems Starting the ZyXEL Utility Program
- 6.2 Problem Connecting to an Access Point
- 6.3 Problem with the Link Status
- 6.4 Problems Communicating With Other Computers
A. Product Specifications
B. Access Point Mode Setup Example
- Configuring the Computer on Which You Install the ZyXEL G- 220 v2
- Configuring the Wireless Station Computer
C. Disable Windows XP Wireless LAN Configuration Tool
- Via the Wireless Network System Tray Icon
- Via the Control Panel
D. Management with Wireless Zero Configuration
- Activating Wireless Zero Configuration
- Connecting to a Wireless Network
- Security Settings
- Association
- Authentication
- Ordering the Preferred Networks
E. Types of EAP Authentication
- EAP-MD5 (Message-Digest Algorithm 5)
- EAP-TLS (Transport Layer Security)
- EAP-TTLS (Tunneled Transport Layer Service)
- PEAP (Protected EAP)
- LEAP
- Dynamic WEP Key Exchange
- WPA(2)
- Encryption
- User Authentication
- WPA(2)-PSK Application Example
- WPA(2) with RADIUS Application Example
- Security Parameters Summary
F. Setting up Your Computer’s IP Address
- Windows 95/98/Me
- Installing Components
- Configuring
- Verifying Settings
- Windows 2000/NT/XP
- Verifying Settings
- Macintosh OS 8/9
- Verifying Settings
- Macintosh OS X
- Verifying Settings
Index
- A
- C
- D
- E
- F
- G
- H
- I
- L
- M
- N
- O
- P
- Q
- R
- S
- T
- U
- V
- W
- Z

ZyXEL G-220 v2 User’s Guide

98 Appendix F Setting up Your Computer’s IP Address

Figure 67 Windows 95/98/Me: TCP/IP Properties: DNS Configuration

4 Click the Gateway tab.

• If you do not know your gateway’s IP address, remove previously

installed gateways.

• If you have a gateway IP address, type it in the New gateway field

and click Add.

5 Click OK to save and close the TCP/IP Properties window.

6 Click OK to close the Network window. Insert the Windows CD if prompted.

7 Restart your computer when prompted.

Verifying Settings

1 Click Start and then Run.

2 In the Run window, type "winipcfg" and then click OK to open the IP Configuration

window.

3 Select your network adapter. You should see your computer's IP address, subnet mask

and default gateway.

Windows 2000/NT/XP

1 For Windows XP, click start, Control Panel. In Windows 2000/NT, click Start,

Settings, Control Panel.