User guide
Table Of Contents
- Part1
- Part2
- Part2
- Part3
- Part4
- Part5
- Dynamic Link Aggregation
- Link Aggregation ID
- RADIUS
- Configuring RADIUS Server Settings
- Configuring IEEE802.1x
- Supported MIBs
- SNMP Traps
- Configuring SNMP
- Setting Up Login Accounts
- Requirements for Using SSH
- HTTPS Example
- Internet Explorer Warning Messages
- Netscape Navigator Warning Messages
- Login Screen
- Strict Priority Queuing (SPQ)
- Weighted Round Robin Scheduling (WRR)
- DiffServ
- DSCP and Per-Hop Behavior
- DHCP “Relay Agent Information Option”
- DHCP Relay Agent Circuit ID Sub-option Format
- Part6
- Part7
- Switch Configuration File
- Access Priority
- The Console Port
- Telnet
- List of Available Commands
- Detailed Command Information
- Logging Out
- User Mode
- Enable Mode
- Configure Mode
- config-vlan Commands
- interface Commands
- show system-information
- show hardware-monitor
- show ip
- show logging
- show interface
- show mac address-table
- Backing up Configuration
- Restoring Configuration
- Using a Different Configuration File
- Resetting to the Factory Default
- no mirror-port
- no https timeout
- no trunk
- no port-access-authenticator
- no ssh
- interface
- bpdu-control
- broadcast-limit
- bandwidth-limit
- mirror
- gvrp
- ingress-check
- frame-type
- vlan-trunking
- spq
- wrr
- egress set
- qos priority
- name
- speed-duplex
- Static Entries (SVLAN Table)
- Dynamic Entries (DVLAN Table)
- GARP Status
- GARP Timer
- GVRP Timer
- Enable GVRP
- Disable GVRP
- Set Port VID
- Set Acceptable Frame Type
- Enable or Disable Port GVRP
- Modify Static VLAN
- Delete VLAN ID
Dimension GS-3012 Gigabit Ethernet Switch
Introduction to CLI 28-19
Table 28-3 Command Summary: Configure Mode
COMMAND DESCRIPTION
ssh <socket-number>
Allows SSH access on the
specified service port.
https <socket-
number>
Allows HTTPS access on the
specified service port.
remote-
management
<index> start-addr
<ip> end-addr <ip>
service
<telnet|ftp|http
|icmp|snmp>
Specifies a group of trusted
computer(s) from which an
administrator may use a service to
manage the switch.
admin-password <pw-string>
<confirm-string>
Changes the administrator
password.
default-
management
<in-band|out-of-
band>
Specifies through which traffic flow
the switch is to send packets.
ssh known-hosts <host-
ip> <1024|ssh-
rsa|ssh-dsa> <key>
Adds a remote host to which the
switch can access using SSH
service.
https cert-regeneration
<rsa|dsa>
Re-generates a certificate.
timeout <0-65535>
Sets the HTTPS timeout period.
multi-login
Enables multi-login.
dhcp-relay
Enables DHCP relay.
helper-address
<svr_ip> [svr2_ip]
[svr3_ip]
Sets the IP addresses of up to 3
DHCP servers.
option
Allows the switch to add DHCP
relay agent information.
information
Allows the switch to add system
name to agent information.
28.9.4 config-vlan Commands
The following table lists the config-vlan commands in configuration mode.
Table 28-4 Command Summary: config-vlan Commands
COMMAND DESCRIPTION
vlan <1-4094>
Creates a new VLAN group.
name <name-str>
Specifies a name for identification
purposes.
normal <port-list>
Specifies the port(s) to dynamically join
this VLAN group using GVRP