User guide
Table Of Contents
- Part1
- Part2
- Part2
- Part3
- Part4
- Part5
- Dynamic Link Aggregation
- Link Aggregation ID
- RADIUS
- Configuring RADIUS Server Settings
- Configuring IEEE802.1x
- Supported MIBs
- SNMP Traps
- Configuring SNMP
- Setting Up Login Accounts
- Requirements for Using SSH
- HTTPS Example
- Internet Explorer Warning Messages
- Netscape Navigator Warning Messages
- Login Screen
- Strict Priority Queuing (SPQ)
- Weighted Round Robin Scheduling (WRR)
- DiffServ
- DSCP and Per-Hop Behavior
- DHCP “Relay Agent Information Option”
- DHCP Relay Agent Circuit ID Sub-option Format
- Part6
- Part7
- Switch Configuration File
- Access Priority
- The Console Port
- Telnet
- List of Available Commands
- Detailed Command Information
- Logging Out
- User Mode
- Enable Mode
- Configure Mode
- config-vlan Commands
- interface Commands
- show system-information
- show hardware-monitor
- show ip
- show logging
- show interface
- show mac address-table
- Backing up Configuration
- Restoring Configuration
- Using a Different Configuration File
- Resetting to the Factory Default
- no mirror-port
- no https timeout
- no trunk
- no port-access-authenticator
- no ssh
- interface
- bpdu-control
- broadcast-limit
- bandwidth-limit
- mirror
- gvrp
- ingress-check
- frame-type
- vlan-trunking
- spq
- wrr
- egress set
- qos priority
- name
- speed-duplex
- Static Entries (SVLAN Table)
- Dynamic Entries (DVLAN Table)
- GARP Status
- GARP Timer
- GVRP Timer
- Enable GVRP
- Disable GVRP
- Set Port VID
- Set Acceptable Frame Type
- Enable or Disable Port GVRP
- Modify Static VLAN
- Delete VLAN ID

Dimension GS-3012 Gigabit Ethernet Switch
Command Examples 29-3
Figure 29-4 show logging Command Example
If you clear a log (by entering
y at the “Clear Error Log (y/n):” prompt), you cannot view it
again.
29.2.5 show interface
Syntax:
show interface [port-number]
This command displays statistics of a port. The following example shows that port 10 is up and the related
information.
Figure 29-5 show interface Command Example
GS-3012# show interface 10
Port Info Port NO. :10
Link :100M/F
Statuss :FORWARDING
LACP :Disabled
TxPkts :69
RxPkts :4
Errors :0
Tx KBs/s :1.684
Rx KBs/s :1.684
Up Time : 0:02:12
TX Packet Tx Packets :69
Multicast :0
Broadcast :0
Pause :0
Tagged :0
RX Packet Tx Packets :4
Multicast :0
Broadcast :4
Pause :0
Control :0
TX Collison Single :0
Multiple :0
Excessive :0
Late :0
Error Packet RX CRC :0
Length :0
Runt :0
Distribution 64 :4
65 to 127 :74
128 to 255 :18
256 to 511 :0
512 to 1023 :0
1024 to 1518 :44
Giant :0
GS-3012#
GS-3012# show logging
50 Thu Jan 1 00:01:54 1970 PP05 -WARN SNMP TRAP 3: link up
51 Thu Jan 1 00:03:04 1970 PINI -WARN SNMP TRAP 0: cold start
52 Thu Jan 1 00:03:04 1970 PP0e -WARN SNMP TRAP 24: Event On Trap
53 Thu Jan 1 00:03:04 1970 PINI INFO main: init completed
54 Thu Jan 1 00:00:02 1970 PINI -WARN SNMP TRAP 0: cold start
55 Thu Jan 1 00:00:02 1970 PP0e -WARN SNMP TRAP 24: Event On Trap
56 Thu Jan 1 00:00:02 1970 PINI INFO main: init completed
57 Thu Jan 1 00:00:02 1970 PINI -WARN SNMP TRAP 0: cold start
58 Thu Jan 1 00:00:02 1970 PP0e -WARN SNMP TRAP 24: Event On Trap
59 Thu Jan 1 00:00:02 1970 PINI INFO main: init completed
Clear Error Log (y/n):