User guide
Table Of Contents
- Part1
- Part2
- Part2
- Part3
- Part4
- Part5
- Dynamic Link Aggregation
- Link Aggregation ID
- RADIUS
- Configuring RADIUS Server Settings
- Configuring IEEE802.1x
- Supported MIBs
- SNMP Traps
- Configuring SNMP
- Setting Up Login Accounts
- Requirements for Using SSH
- HTTPS Example
- Internet Explorer Warning Messages
- Netscape Navigator Warning Messages
- Login Screen
- Strict Priority Queuing (SPQ)
- Weighted Round Robin Scheduling (WRR)
- DiffServ
- DSCP and Per-Hop Behavior
- DHCP “Relay Agent Information Option”
- DHCP Relay Agent Circuit ID Sub-option Format
- Part6
- Part7
- Switch Configuration File
- Access Priority
- The Console Port
- Telnet
- List of Available Commands
- Detailed Command Information
- Logging Out
- User Mode
- Enable Mode
- Configure Mode
- config-vlan Commands
- interface Commands
- show system-information
- show hardware-monitor
- show ip
- show logging
- show interface
- show mac address-table
- Backing up Configuration
- Restoring Configuration
- Using a Different Configuration File
- Resetting to the Factory Default
- no mirror-port
- no https timeout
- no trunk
- no port-access-authenticator
- no ssh
- interface
- bpdu-control
- broadcast-limit
- bandwidth-limit
- mirror
- gvrp
- ingress-check
- frame-type
- vlan-trunking
- spq
- wrr
- egress set
- qos priority
- name
- speed-duplex
- Static Entries (SVLAN Table)
- Dynamic Entries (DVLAN Table)
- GARP Status
- GARP Timer
- GVRP Timer
- Enable GVRP
- Disable GVRP
- Set Port VID
- Set Acceptable Frame Type
- Enable or Disable Port GVRP
- Modify Static VLAN
- Delete VLAN ID
Dimension GS-3012 Gigabit Ethernet Switch
Introducing the Web Configurator 4-5
Table 4-3 Navigation Panel Sub-link Descriptions
LABEL DESCRIPTION
Bandwidth Control This link takes you to screens where you can cap the maximum bandwidth allowed from
specified source(s) to specified destination(s).
Broadcast Storm
Control
This link takes you to a screen to set up broadcast filters.
Mirroring This link takes you to screens where you can copy traffic from one port or ports to another
port in order that you can examine the traffic from the first port without interference
Link Aggregation This link takes you to a screen where you can logically trunk physical links to form one
logical, higher-bandwidth link.
Port Authentication This link takes you to a screen where you can configure RADIUS (Remote Authentication
Dial-In User Service), a protocol for user authentication that allows you to use an external
server to validate an unlimited number of users.
Port Security This link takes you to a screen where you can activate MAC address learning and set the
maximum number of MAC addresses to learn on a port.
Access Control This link takes you to screens where you can change the system login password and
configure SNMP and remote management.
Queuing Method This link takes you to a screen where you can configure SPQ or WRR with associated
queue weights for each port.
Classifier This link takes you to a screen where you can configure classifiers.
Policy Rule This link takes you to a screen where you can configure policy rules.
DHCP Relay This link takes you to a screen where you can configure DHCP relay information.
Routing Protocol
Static Routing This link takes you to screens where you can configure static routes. A static route
defines how the GS-3012 should forward traffic by configuring the TCP/IP parameters
manually.
Management
Maintenance This link takes you to screens where you can perform firmware and configuration file
maintenance as well as reboot the system.
Diagnostic This link takes you to screens where you can view system logs and test port(s).
Cluster Management This link takes you to a screen where you can configure clustering management and view
its status.
MAC Table This link takes you to a screen where you can view the MAC addresses (and types) of
devices attached to what ports and VLAN IDs.
ARP Table This link takes you to a screen where you can view the MAC addresses – IP address
resolution table.
4.3.1 Change Your Password
After you log in for the first time, it is recommended you change the default Administrator password in the
Logins screen. Click Advanced Application, Access Control and then Logins to display the next screen.