P-2002 Series VoIP Analog Telephone Adaptor User’s Guide Version 3.
P-2002 Series User’s Guide Copyright Copyright © 2005 by ZyXEL Communications Corporation. The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the prior written permission of ZyXEL Communications Corporation. Published by ZyXEL Communications Corporation.
P-2002 Series User’s Guide Federal Communications Commission (FCC) Interference Statement This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operations. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules.
P-2002 Series User’s Guide Federal Communications Commission (FCC) Interference Statement 5
P-2002 Series User’s Guide Safety Warnings For your safety, be sure to read and follow all warning notices and instructions. • To reduce the risk of fire, use only No. 26 AWG (American Wire Gauge) or larger telecommunication line cord. • Do NOT open the device or unit. Opening or removing covers can expose you to dangerous high voltage points or other risks. ONLY qualified service personnel can service the device. Please contact your vendor for further information.
P-2002 Series User’s Guide ZyXEL Limited Warranty ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in materials or workmanship for a period of up to two years from the date of purchase.
P-2002 Series User’s Guide Customer Support Please have the following information ready when you contact customer support. • • • • Product model and serial number. Warranty Information. Date that you received your device. Brief description of the problem and the steps you took to solve it. TELEPHONEA WEB SITE SALES E-MAIL FAX FTP SITE support@zyxel.com.tw +886-3-578-3942 sales@zyxel.com.tw +886-3-578-2439 www.zyxel.com ZyXEL Communications Corp. www.europe.zyxel.
P-2002 Series User’s Guide TELEPHONEA WEB SITE SALES E-MAIL FAX FTP SITE support@zyxel.co.uk +44 (0) 1344 303044 08707 555779 (UK only) www.zyxel.co.uk sales@zyxel.co.uk +44 (0) 1344 303034 ftp.zyxel.co.uk METHOD SUPPORT E-MAIL REGULAR MAIL LOCATION UNITED KINGDOM ZyXEL Communications UK Ltd.,11 The Courtyard, Eastern Road, Bracknell, Berkshire, RG12 2XB, United Kingdom (UK) a. “+” is the (prefix) number you enter to make an international telephone call.
P-2002 Series User’s Guide 10 Customer Support
P-2002 Series User’s Guide Table of Contents Copyright .................................................................................................................. 3 Federal Communications Commission (FCC) Interference Statement ............... 4 Safety Warnings ....................................................................................................... 6 ZyXEL Limited Warranty.......................................................................................... 7 Customer Support....
P-2002 Series User’s Guide 3.2 General Setup ....................................................................................................35 3.2.1 Domain Name ...........................................................................................35 3.3 General Setup Configuration ..............................................................................35 3.4 Configuring Password ........................................................................................36 3.
P-2002 Series User’s Guide 5.6 Voice Coding ......................................................................................................54 5.6.1 G.711 .........................................................................................................55 5.6.2 G.729 ........................................................................................................55 5.7 PSTN Call Setup Signaling ................................................................................55 5.
P-2002 Series User’s Guide Chapter 8 Phone Book ............................................................................................................ 75 8.1 Phone Book Introduction ....................................................................................75 8.1.1 Speed Dial ................................................................................................75 8.1.1.1 Peer-to-Peer Calls ...........................................................................75 8.1.
P-2002 Series User’s Guide 12.8 Problems with Voice Service ............................................................................98 12.9 Pop-up Windows, JavaScripts and Java Permissions .....................................99 12.9.1 Internet Explorer Pop-up Blockers ..........................................................99 12.9.1.1 Disable Pop-up Blockers ...............................................................99 12.9.1.2 Enable Pop-up Blockers with Exceptions ..............................
P-2002 Series User’s Guide 16 Table of Contents
P-2002 Series User’s Guide List of Figures Figure 1 LEDs ........................................................................................................ 26 Figure 2 Internet Telephony Service Provider Application ..................................... 27 Figure 3 IP-PBX Application .................................................................................. 27 Figure 4 Peer-to-peer Calling .................................................................................
P-2002 Series User’s Guide Figure 39 Configuration ......................................................................................... 89 Figure 40 Configuration Upload Successful ........................................................... 90 Figure 41 Network Temporarily Disconnected ....................................................... 90 Figure 42 Reset Warning Message ........................................................................ 91 Figure 43 Restart Screen ............................
P-2002 Series User’s Guide List of Tables Table 1 LED Descriptions ...................................................................................... 26 Table 2 Web Configurator Screens Summary ....................................................... 32 Table 3 Common Screen Command Buttons ........................................................ 33 Table 4 System General ........................................................................................ 36 Table 5 Password ........................
P-2002 Series User’s Guide Table 39 Troubleshooting Telephone .................................................................... 98 Table 40 Troubleshooting Voice Service ............................................................... 98 Table 41 Device Specifications .............................................................................. 107 Table 42 Feature Specifications ............................................................................ 108 Table 43 Power Adaptor Specifications .......
P-2002 Series User’s Guide Preface Congratulations on your purchase of the Prestige 2002 Series VoIP Analog Telephone Adaptor. Note: Register your product online to receive e-mail notices of firmware upgrades and information at www.zyxel.com for global products, or at www.us.zyxel.com for North American products. Your Prestige is easy to install and configure.
P-2002 Series User’s Guide • Mouse action sequences are denoted using a comma. For example, “click the Apple icon, Control Panels and then Modem” means first click the Apple icon, then point your mouse pointer to Control Panels and then click Modem. • For brevity’s sake, we will use “e.g.,” as a shorthand for “for instance”, and “i.e.,” for “that is” or “in other words” throughout this manual. • The Prestige 2002 series may be referred to as the Prestige or the device in this user’s guide.
P-2002 Series User’s Guide CHAPTER 1 Introducing the Prestige This chapter introduces the main features and applications of the Prestige. 1.1 Prestige VoIP Analog Telephone Adaptor Overview The Prestige is a SIP-based VoIP analog telephone adaptor (ATA). Sending voice signals over the Internet is called Voice over IP or VoIP. Session Initiated Protocol (SIP) is an internationally recognized standard for implementing VoIP.
P-2002 Series User’s Guide Auto-crossover 10/100 Mbps Ethernet Interfaces The Ethernet interfaces automatically adjust to either a crossover or straight-through Ethernet cable. PSTN Lifeline The Prestige 2002L has a LINE port for connecting a PSTN line. You can receive incoming PSTN phone calls even while someone else connected to the Prestige is making VoIP phone calls. You can dial a (prefix) number to make an outgoing PSTN call. You can still make PSTN phone calls if the Prestige 2002L loses power.
P-2002 Series User’s Guide Comfort Noise Generation The Prestige generates background noise to fill moments of silence when the other device in a call stops transmitting because the other party is not speaking (as total silence could easily be mistaken for a lost connection). Echo Cancellation The Prestige supports G.168, an ITU-T standard for eliminating the echo caused by the sound of your voice reverberating in the telephone receiver while you talk.
P-2002 Series User’s Guide Figure 1 LEDs Table 1 LED Descriptions LED COLOR STATUS DESCRIPTION PWR/VoIP Green On The Prestige is receiving power. Blinking The Prestige is self-testing. On The VoIP SIP registration was successful. Off The Prestige is not receiving power. On The Prestige has an Ethernet connection with the cable/DSL modem. Blinking The Prestige is sending/receiving data to/from the cable/DSL modem.
P-2002 Series User’s Guide Figure 2 Internet Telephony Service Provider Application 1.5.2 Make Calls via IP-PBX If your company has an IP-PBX (Internet Protocol Private Branch Exchange), you can use the Prestige to make and receive VoIP telephone calls through it. In this example, you use your analog phone (A in the figure) and the Prestige (B) changes the call into VoIP and sends it to the IP-PBX. The IP-PBX forwards calls to PSTN phones (C) to the PSTN network.
P-2002 Series User’s Guide The following figure shows a basic example of how you would make a peer-to-peer VoIP call. You use your analog phone (A in the figure) and the Prestige (B) changes the call into VoIP. The Prestige then sends your call through your modem or router (C) and the Internet to the peer VoIP device (D).
P-2002 Series User’s Guide CHAPTER 2 Introducing the Web Configurator This chapter describes how to access the Prestige web configurator and provides an overview of its screens. 2.1 Web Configurator Overview The web configurator is an HTML-based management interface that allows easy Prestige setup and management via Internet browser. Use Internet Explorer 6.0 and later or Netscape Navigator 7.0 and later versions. The recommended screen resolution is 1024 by 768 pixels.
P-2002 Series User’s Guide Figure 5 Web Configurator IP Address 4 Type "1234" (default) as the password and click Login. In some versions, the default password appears automatically - if this is the case, click Login. Figure 6 Enter Password 5 You should see a screen asking you to change your password (highly recommended) as shown next. Type a new password (and retype it to confirm) and click Apply or click Ignore.
P-2002 Series User’s Guide 2.3 Resetting the Prestige If you forget your password or cannot access the web configurator, you will need to reload the factory-default configuration file or use the RESET button on the back of the Prestige. Uploading this configuration file replaces the current configuration file with the factorydefault configuration file. This means that you will lose all configurations that you had previously. The password will also be reset to “1234”. 2.3.
P-2002 Series User’s Guide Figure 8 Web Configurator The following table describes the navigation panel and sub-menus. Table 2 Web Configurator Screens Summary LINK TAB FUNCTION SYSTEM General Use this screen to configure general system settings. Password Use this screen to change your password. Time Setting Use this screen to change your Prestige’s time and date. Ethernet Use this screen to configure your Prestige’s Ethernet interface settings.
P-2002 Series User’s Guide 2.5 Common Screen Command Buttons The following table shows common command buttons found on many web configurator screens. Table 3 Common Screen Command Buttons Apply Click Apply to save your changes back to the Prestige. Reset/Cancel Click Reset or Cancel to begin configuring this screen afresh.
P-2002 Series User’s Guide 34 Chapter 2 Introducing the Web Configurator
P-2002 Series User’s Guide CHAPTER 3 System Screens This chapter provides information on the System screens. 3.1 System Overview This chapter describes the SYSTEM screens. 3.2 General Setup General Setup contains administrative and system-related information. System Name is for identification purposes. However, because some ISPs check this name you should enter your computer's "Computer Name". • In Windows 95/98 click Start, Settings, Control Panel, Network.
P-2002 Series User’s Guide Figure 9 System General Table 4 System General LABEL DESCRIPTION System Name This is for identification purposes. Enter your computer's "Computer Name". Domain Name The Domain Name entry is what is propagated to the DHCP clients on the LAN. If you leave this blank, the domain name obtained by DHCP from the ISP is used. Administrator Inactivity Timer Type how many minutes a management session can be left idle before the session times out. The default is 5 minutes.
P-2002 Series User’s Guide Table 5 Password LABEL DESCRIPTION Old Password Type the default password or the existing password you use to access the system in this field. Use up to 32 ASCII characters. New Password Type the new password in this field. Retype to Confirm Type the new password again in this field. Apply Click Apply to save your changes back to the Prestige. Reset Click Reset to begin configuring this screen afresh. 3.
P-2002 Series User’s Guide Figure 11 Time Setting The following table describes the labels in this screen. Table 7 Time Setting 38 LABEL DESCRIPTION Time Protocol Select the time service protocol that your time server sends when you turn on the Prestige. Not all time servers support all protocols, so you may have to check with your ISP/network administrator or use trial and error to find a protocol that works. The main difference between them is the format.
P-2002 Series User’s Guide Table 7 Time Setting (continued) LABEL DESCRIPTION Time Zone Choose the Time Zone of your location. This will set the time difference between your time zone and Greenwich Mean Time (GMT). Daylight Savings Select this option if you use daylight savings time. Daylight saving is a period from late spring to early fall when many countries set their clocks ahead of normal local time by one hour to give more daytime light in the evening.
P-2002 Series User’s Guide 40 Chapter 3 System Screens
P-2002 Series User’s Guide CHAPTER 4 Ethernet Screens This chapter describes how to configure the Prestige’s Ethernet and management IP addresses settings. 4.1 ETHERNET Overview The Prestige has two Ethernet ports. Connect the LAN Ethernet port to a cable/DSL modem or router or an Ethernet LAN switch, which in turn connects you to the Internet or your company’s IP-PBX. Connect the PC Ethernet port to your computer.
P-2002 Series User’s Guide 4.1.3 PPPoE Encapsulation Point-to-Point Protocol over Ethernet (PPPoE) functions as a dial-up connection. PPPoE is an IETF (Internet Engineering Task Force) draft standard specifying how a host personal computer interacts with a broadband modem (for example DSL, cable, wireless, etc.) to achieve access to high-speed data networks. For the service provider, PPPoE offers an access and authentication method that works with existing access control systems (for instance, Radius).
P-2002 Series User’s Guide Figure 12 ETHERNET Table 8 ETHERNET LABEL DESCRIPTION Get IP Address Automatically Select this option if you have a dynamic IP address. Use Fixed IP Address Select this option if the ISP assigned you a static IP address. IP Address Type the (static) IP address assigned to you by your ISP. Subnet Mask Type the subnet mask assigned to you by your ISP (if given). Default Gateway Enter the gateway IP address assigned to you by your ISP (if given).
P-2002 Series User’s Guide 4.3 Configuring the Ethernet Management Port Click ETHERNET in the navigation panel and then Mgnt Port to open the following screen. Use the ETHERNET Mgnt Port screen to configure a static IP address through which you can manage the Prestige. Note: The management port is a separate logical Ethernet interface that you can access from a computer connected to either of the Prestige’s physical Ethernet interfaces.
P-2002 Series User’s Guide CHAPTER 5 Introduction to VoIP This chapter provides background information on VoIP and SIP. 5.1 Introduction to VoIP VoIP is the sending of voice signals over the Internet Protocol. This allows you to make phone calls and send faxes over the Internet at a fraction of the cost of using the traditional circuitswitched telephone network. You can also use servers to run telephone service applications like PBX services and voice mail.
P-2002 Series User’s Guide 5.2.2 SIP Call Progression The following figure displays the basic steps in the setup and tear down of a SIP call. A calls B. Table 10 SIP Call Progression A B 1. INVITE 2. Ringing 3. OK 4. ACK 5.Dialogue (voice traffic) 6. BYE 7. OK 1 A sends a SIP INVITE request to B. This message is an invitation for B to participate in a SIP telephone call. 2 B sends a response indicating that the telephone is ringing. 3 B sends an OK response after the call is answered.
P-2002 Series User’s Guide Figure 14 SIP User Agent 5.2.3.2 SIP Proxy Server A SIP proxy server receives requests from clients and forwards them to another server. In the following example, you want to use client device A to call someone who is using client device C. 1 The client device (A in the figure) sends a call invitation to the SIP proxy server (B). 2 The SIP proxy server forwards the call invitation to C. Figure 15 SIP Proxy Server 5.2.3.
P-2002 Series User’s Guide Figure 16 SIP Redirect Server 5.2.3.4 SIP Register Server A SIP register server maintains a database of SIP identity-to-IP address (or domain name) mapping. The register server checks your user name and password when you register. 5.2.4 RTP When you make a VoIP call using SIP, the RTP (Real time Transport Protocol) is used to handle voice data transfer. See RFC 1889 for details on RTP. 5.
P-2002 Series User’s Guide NAT may be implemented on a device that is between your Prestige and the Internet. 5.3.1 NAT Example See the following figure. The Prestige (X) sends packets to the Internet. The Prestige’s IP address is 10.0.0.3. This is a private or internal IP address. The NAT router maps the private source IP address to a public source IP address (a.b.c.d). The public source IP address is also known as the external IP address.
P-2002 Series User’s Guide The following table summarizes how these NAT types handle outgoing and incoming packets. Read the following sections for more details and examples. Table 11 NAT Types FULL CONE Incoming Any external host Packets can send packets to the mapped external IP address and port. RESTRICTED CONE Only external hosts with an IP address to which the internal host has already sent a packet can send packets to the mapped external IP address and port.
P-2002 Series User’s Guide Figure 19 Full Cone NAT Example 5.3.2.2 Restricted Cone NAT As in full cone NAT, a restricted cone NAT router maps all outgoing packets from an internal IP address and port to a single IP address and port on the external network. In the following example, the NAT router maps the source address of all packets sent from internal IP address 1 and port A to IP address 2 and port B on the external network.
P-2002 Series User’s Guide 5.3.2.3 Port Restricted Cone NAT As in full cone NAT, a port restricted cone NAT router maps all outgoing packets from an internal IP address and port to a single IP address and port on the external network. In the following example, the NAT router maps the source address of all packets sent from internal IP address 1 and port A to IP address 2 and port B on the external network.
P-2002 Series User’s Guide Figure 22 Symmetric NAT 5.4 NAT and SIP Some NAT routers are not SIP-friendly and will stop your voice sessions. The Prestige must register its public IP address with a SIP register server. If there is a NAT router between the Prestige and the SIP register server, the Prestige probably has a private IP address. The Prestige lists its IP address in the SIP message that it sends to the SIP register server. NAT does not translate this IP address in the SIP message.
P-2002 Series User’s Guide 5.4.3 STUN STUN (Simple Traversal of User Datagram Protocol (UDP) through Network Address Translators) allows the Prestige to find the presence and types of NAT routers and/or firewalls between it and the public Internet. STUN also allows the Prestige to find the public IP address that NAT assigned, so the Prestige can embed it in the SIP data stream. STUN does not work with symmetric NAT routers (see Section 5.3.2.4 on page 52) or firewalls. See RFC 3489 for details on STUN.
P-2002 Series User’s Guide 5.6.1 G.711 G.711 is a Pulse Code Modulation (PCM) waveform codec. G.711 provides very good sound quality but requires 64kbps of bandwidth. 5.6.2 G.729 G.729 is an Analysis-by-Synthesis (AbS) hybrid waveform codec that uses a filter based on information about how the human vocal tract produces sounds. G.729 provides good sound quality and reduces the required bandwidth to 8kbps. 5.
P-2002 Series User’s Guide 56 Chapter 5 Introduction to VoIP
P-2002 Series User’s Guide CHAPTER 6 VoIP Screens This chapter describes how to configure advanced VoIP and QoS settings. 6.1 VoIP Introduction VoIP is the sending of voice signals over the Internet Protocol. This chapter covers the configuration of the VoIP screens. 6.2 VoIP Configuration Click VoIP in the navigation panel to display the following screen. Use this screen to configure the Prestige’s VoIP settings.
P-2002 Series User’s Guide Figure 24 VoIP Table 12 VoIP 58 LABEL DESCRIPTION SIP Account You can configure the Prestige to use multiple SIP accounts. Select one to configure its settings on the Prestige. Active Select this check box to have the Prestige use this SIP account. Clear the check box to have the Prestige not use this SIP account. SIP Number Enter your SIP number in this field (use the number or text that comes before the @ symbol in a full SIP URI).
P-2002 Series User’s Guide Table 12 VoIP (continued) LABEL DESCRIPTION SIP Server Port Enter the SIP server’s listening port for SIP in this field. Leave this field set to the default if your VoIP service provider did not give you a server port number for SIP. REGISTER Server Address Enter the SIP register server’s address in this field. If you were not given a register server address, then enter the address from the SIP Server Address field again here.
P-2002 Series User’s Guide 2 Press a number from 1101~1108 on your phone followed by the “#” key. 3 Play your desired music or voice recording into the receiver’s mouthpiece. Press the “#” key. 4 You can continue to add, listen to, or delete tones, or you can hang up the receiver when you are done. 6.3.0.2 Listening to Custom Tones Do the following to listen to a custom tone: 1 Pick up the phone and press “****” on your phone’s keypad and wait for the message that says you are in the configuration menu.
P-2002 Series User’s Guide Figure 25 VoIP Advanced Chapter 6 VoIP Screens 61
P-2002 Series User’s Guide The following table describes the labels in this screen. Table 13 VoIP Advanced LABEL DESCRIPTION Advanced VoIP Settings This read-only field displays the number of the SIP account that you are configuring. The changes that you save in this page affect the Prestige’s settings with the SIP account displayed here. SIP Server Settings 62 URL Type Select SIP to have the Prestige include the domain name with the SIP number in the SIP messages that it sends.
P-2002 Series User’s Guide Table 13 VoIP Advanced (continued) LABEL DESCRIPTION Server Port Enter the STUN server’s listening port for STUN requests in this field. Leave this field set to the default if your VoIP service provider did not give you a server port number for STUN. Use NAT Enable this feature to use a NAT router’s public IP address and SIP port number in the Prestige’s SIP messages. You must also configure the NAT router to forward traffic with this port number to the Prestige.
P-2002 Series User’s Guide Table 13 VoIP Advanced (continued) LABEL DESCRIPTION Fax Option Use this field to set how the Prestige handles fax messages. You can select either the Fax Pass-through or the T.38 fax methods. Select Fax Pass-through to have the Prestige send fax messages over G.711. The peer devices must also use G.711. Select T.38 to have the Prestige send fax messages over the IP network as UDP or TCP/IP packets.
P-2002 Series User’s Guide 6.5.2.1 DSCP and Per-Hop Behavior DiffServ defines a new DS (Differentiated Services) field to replace the Type of Service (TOS) field in the IP header. The DS field contains a 2-bit unused field and a 6-bit DSCP field which can define up to 64 service levels. The following figure illustrates the DS field. DSCP is backward compatible with the three precedence bits in the ToS octet so that nonDiffServ compliant, ToS-enabled network device will not conflict with the DSCP mapping.
P-2002 Series User’s Guide Figure 27 QoS The following table describes the labels in this screen. Table 14 QoS 66 LABEL DESCRIPTION SIP TOS Priority Type a priority for voice transmissions. The Prestige applies Type of Service priority tags with this priority to voice traffic that it transmits. RTP TOS Priority Type a priority for voice transmissions. The Prestige applies Type of Service priority tags with this priority to RTP traffic that it transmits.
P-2002 Series User’s Guide CHAPTER 7 Phone This chapter covers how to adjust the Prestige’s phone settings. 7.1 Phone Introduction You can configure the volume, echo cancellation and VAD settings for each individual phone port on the Prestige. You can also select which SIP account to use for making outgoing calls. 7.1.1 Voice Activity Detection/Silence Suppression Voice Activity Detection (VAD) detects whether or not speech is present.
P-2002 Series User’s Guide Figure 28 Phone Port The following table describes the labels in this screen. Table 15 Phone Port 68 LABEL DESCRIPTION Phone Port Settings Use this field to select the phone port that you want to configure. Speaking Volume Use this field to set the loudness that the Prestige uses for the speech signal that it sends to the peer device. -1 is the quietest and 1 is the loudest.
P-2002 Series User’s Guide Table 15 Phone Port (continued) LABEL DESCRIPTION Apply Click Apply to save your changes back to the Prestige. Reset Click Reset to begin configuring this screen afresh. 7.3 Supplementary Phone Services Overview Supplementary services such as call hold, call waiting, call transfer, … are generally available from your voice service provider.
P-2002 Series User’s Guide After pressing the flash key, if you do not issue the sub-command before the default subcommand timeout (2 seconds) expires or issue an invalid sub-command, the current operation will be aborted. Table 16 European Flash Key Commands COMMAND SUB-COMMAND Flash DESCRIPTION Put a current call on hold to place a second call. Switch back to the call (if there is no second call). Flash 0 Drop the call presently on hold or reject an incoming call which is waiting for answer.
P-2002 Series User’s Guide • Put the first call on hold and answer the second call. Press the flash key and then “2”. 7.3.2.3 European Call Transfer Do the following to transfer an incoming call (that you have answered) to another phone. 1 Press the flash key to put the caller on hold. 2 When you hear the dial tone, dial “*98#” followed by the number to which you want to transfer the call. to operate the Intercom. 3 After you hear the ring signal or the second party answers it, hang up the phone. 7.3.2.
P-2002 Series User’s Guide If you have another call, press the flash key to switch back and forth between caller A and B by putting either one on hold. If you hang up the phone but a caller is still on hold, there will be a remind ring. 7.3.3.2 USA Call Waiting This allows you to place a call on hold while you answer another incoming call on the same telephone (directory) number. If there is a second call to your telephone number, you will hear a call waiting tone.
P-2002 Series User’s Guide Figure 29 Phone Common The following table describes the labels in this screen. Table 18 Phone Common LABEL DESCRIPTION Country Code Use the drop-down list box to select the country where your Prestige is located. Immediate Dial Use immediate dial to have the Prestige make calls right away instead of waiting for the dialing interval (the time period it waits to make sure you are done pressing the keys). In order to use immediate dial, enable it here.
P-2002 Series User’s Guide 74 Chapter 7 Phone
P-2002 Series User’s Guide CHAPTER 8 Phone Book This chapter covers how to configure the Prestige’s phone book. 8.1 Phone Book Introduction You can use the phone book feature to configure speed dial entries, call forwarding tables and the lifeline settings. 8.1.1 Speed Dial Speed dial provides shortcuts for dialing frequently used (VoIP) phone numbers. 8.1.1.1 Peer-to-Peer Calls You can call another VoIP device directly without going through a SIP server.
P-2002 Series User’s Guide Figure 30 Speed Dial The following table describes the labels in this screen. Table 19 Speed Dial LABEL DESCRIPTION Add New Entry Use this section of the screen to edit and save new or existing speed dial phone book entries. Speed Dial Select a speed dial key combination from the drop-down list box. After configuring the speed dial entry and adding it to the phonebook, dial this speed dial key combination to use the speed dial entry to make a call.
P-2002 Series User’s Guide Table 19 Speed Dial (continued) LABEL DESCRIPTION Speed Dial This is the entry’s speed dial key combination. Press this key combination on a telephone attached to the Prestige in order to call the party named in this entry. Name This is the descriptive name of the party that you will use this speed dial entry to call. SIP Number This is the SIP number of the party that you will call. Type This field displays Use Proxy if calls to this party use one of your SIP accounts.
P-2002 Series User’s Guide Figure 31 Call Forward The following table describes the labels in this screen.
P-2002 Series User’s Guide Table 20 Call Forward LABEL DESCRIPTION Table Number Select which call forwarding table you want to configure. You can configure a different call forwarding table for each SIP account or use the same call forwarding table for both. The following applies to the number fields in this screen. For a SIP number, use the number or text that comes before the @ symbol in a full SIP URI. You can use up to 127 ASCII characters.
P-2002 Series User’s Guide 8.4 Lifeline Configuration (Prestige 2002L) Click PHONEBOOK in the navigation panel and then Lifeline to display the following screen. Figure 32 Lifeline The following table describes the labels in this screen. Table 21 Lifeline 80 LABEL DESCRIPTION PSTN Pre-fix Number Specify the prefix number for dialing regular calls.
P-2002 Series User’s Guide CHAPTER 9 Logs This chapter contains information about the Prestige’s Logs screen. Refer to the Appendices for example log message explanations. 9.1 Viewing Logs The web configurator allows you to look at all of the Prestige’s logs in one location. Click LOGS in the navigation panel to open the View Log screen. Use the View Log screen to display the Prestige’s logs. Log entries in red indicate system error logs.
P-2002 Series User’s Guide Table 22 View Log (continued) LABEL DESCRIPTION Destination This field lists the destination IP address and the port number of the incoming packet. Note This field displays additional information about the log entry. 9.2 Log Message Descriptions The following tables provide descriptions of example log messages. Table 23 System Error Logs LOG MESSAGE DESCRIPTION WAN connection is down. A WAN connection is down. You cannot access the network through this interface.
P-2002 Series User’s Guide Table 24 System Maintenance Logs (continued) LOG MESSAGE DESCRIPTION Too large ICMP packet has been dropped The device dropped an ICMP packet that was too large. Configuration Change: PC = 0x%x, Task ID = 0x%x The device is saving configuration changes. Table 25 SIP Logs LOG MESSAGE DESCRIPTION SIP Registration Success by SIP:SIP Phone Number The listed SIP account was successfully registered with a SIP register server.
P-2002 Series User’s Guide Table 27 FSM Logs: Caller Side LOG MESSAGE DESCRIPTION VoIP Call Start Ph[Phone Port Number] <- Outgoing Call Number Someone used a phone connected to the listed phone port to initiate a VoIP call to the listed destination. VoIP Call Established Ph[Phone Port] -> Outgoing Call Number Someone used a phone connected to the listed phone port to make a VoIP call to the listed destination.
P-2002 Series User’s Guide CHAPTER 10 Maintenance This chapter displays system information such as ZyNOS firmware, port IP addresses and port traffic statistics. 10.1 Maintenance Overview The maintenance screens can help you view system information, upload new firmware, manage configuration and restart your Prestige. 10.2 Status Screen Click MAINTENANCE in the navigation panel to open the Status screen, where you can use to monitor your Prestige.
P-2002 Series User’s Guide The following table describes the labels in this screen. Table 30 System Status LABEL DESCRIPTION System Name This is the System Name you chose in the SYSTEM General screen. It is for identification purposes Model Name The model name identifies your device type. The model name should also be on a sticker on your device. If you are uploading firmware, be sure to upload firmware for this exact model name.
P-2002 Series User’s Guide Figure 35 Firmware Upload The following table describes the labels in this screen. Table 31 Firmware Upload LABEL DESCRIPTION File Path Type in the location of the file you want to upload in this field or click Browse... to find it. Browse... Click Browse... to find the .bin file you want to upload. Remember that you must decompress compressed (.zip) files before you can upload them. Upload Click Upload to begin the upload process. This process may take up to two minutes.
P-2002 Series User’s Guide Figure 37 Network Temporarily Disconnected After two minutes, log in again and check your new firmware version in the System Status screen. If the upload was not successful, the following screen will appear. Click Return to go back to the F/W Upload screen. Figure 38 Firmware Upload Error 10.4 Configuration Screen Click MAINTENANCE in the navigation panel and then the Configuration tab.
P-2002 Series User’s Guide Figure 39 Configuration 10.4.1 Backup Configuration Backup Configuration allows you to back up (save) the device’s current configuration to a file on your computer. Once your device is configured and functioning properly, it is highly recommended that you back up your configuration file before making configuration changes. The backup configuration file will be useful in case you need to return to your previous settings.
P-2002 Series User’s Guide Note: Do not turn off the device while configuration file upload is in progress. After you see a “configuration upload successful” screen, you must then wait one minute before logging into the device again. Figure 40 Configuration Upload Successful The device automatically restarts in this time causing a temporary network disconnect. In some operating systems, you may see the following icon on your desktop.
P-2002 Series User’s Guide Figure 42 Reset Warning Message You can also press the RESET button on the rear panel to reset the factory defaults of your Prestige. For more information on the RESET button, see Section 2.3 on page 31. 10.5 Restart Screen System restart allows you to reboot the Prestige without turning the power off. Click MAINTENANCE in the navigation panel and then Restart. Click Restart to have the Prestige reboot. This does not affect the Prestige's configuration.
P-2002 Series User’s Guide 92 Chapter 10 Maintenance
P-2002 Series User’s Guide C H A P T E R 11 Phone Usage This chapter describes how to use a phone connected to your Prestige for basic tasks. 11.1 Dialing a Telephone Number The VoIP/PWR LED turns orange when your SIP account is registered. Dial a SIP number like “12345” on your phone’s keypad. Use speed dial entries (see Section 8.2 on page 75) for peer-to-peer calls or SIP numbers that use letters. Dial the speed dial entry on your telephone’s keypad.
P-2002 Series User’s Guide 11.5 Auto Firmware Upgrade During auto-provisioning, the Prestige checks to see if there is a newer firmware version. If newer firmware is available, the Prestige plays a recording when you pick up your phone’s handset. Press “*99#” to upgrade the Prestige’s firmware. Press “#99#” to not upgrade the Prestige’s firmware.
P-2002 Series User’s Guide CHAPTER 12 Troubleshooting This chapter covers potential problems and the corresponding remedies. 12.1 Problems Starting Up the Prestige Table 33 Troubleshooting the Start-Up of Your Prestige PROBLEM CORRECTIVE ACTION None of the Make sure that the Prestige’s power adaptor is connected to the Prestige and an LEDs turn on appropriate power source. Check that the power source is turned on. when I turn on Disconnect the Prestige’s power and reconnect it. the Prestige.
P-2002 Series User’s Guide 12.3 Problems with the LAN Interface Table 35 Troubleshooting the LAN Interface PROBLEM CORRECTIVE ACTION I cannot access the Prestige from the LAN. If the LAN or PC LED is off, see Table 34 on page 95. Make sure that the IP address and the subnet mask of the Prestige and your computer(s) are on the same subnet. I cannot ping any computer on the LAN. If the LAN and PC LEDs are both off, see Table 34 on page 95.
P-2002 Series User’s Guide 12.5 Problems with the Web Configurator Table 37 Troubleshooting the Web Configurator PROBLEM CORRECTIVE ACTION I cannot access the If the Prestige’s Ethernet IP address or management IP address has changed, web configurator. then enter the new one as the URL. Your computer’s IP address must be on the same subnet as the Prestige’s Ethernet IP address or management IP address (whichever you use to access the Prestige). See Section 12.
P-2002 Series User’s Guide 12.7 Problems with Telephone or Telephone Port Table 39 Troubleshooting Telephone PROBLEM CORRECTIVE ACTION There is no dial tone or I can’t make or receive calls. or There is beeping instead of the dial tone. Check the telephone connections and telephone wire. Beeping means that there is not a SIP account registered for the phone to use. You can check the Prestige’s IP addresses and VoIP status in the Maintenance Status screen.
P-2002 Series User’s Guide 12.9 Pop-up Windows, JavaScripts and Java Permissions In order to use the web configurator you need to allow: • Web browser pop-up windows from your device. • JavaScripts (enabled by default). • Java permissions (enabled by default). Note: Internet Explorer 6 screens are used here. Screens for other Internet Explorer versions may vary. 12.9.1 Internet Explorer Pop-up Blockers You may have to disable pop-up blocking to log into your device.
P-2002 Series User’s Guide Figure 45 Internet Options 3 Click Apply to save this setting. 12.9.1.2 Enable Pop-up Blockers with Exceptions Alternatively, if you only want to allow pop-up windows from your device, see the following steps. 1 In Internet Explorer, select Tools, Internet Options and then the Privacy tab. 2 Select Settings…to open the Pop-up Blocker Settings screen.
P-2002 Series User’s Guide Figure 46 Internet Options 3 Type the IP address of your device (the web page that you do not want to have blocked) with the prefix “http://”. For example, http://192.168.1.1. 4 Click Add to move the IP address to the list of Allowed sites.
P-2002 Series User’s Guide Figure 47 Pop-up Blocker Settings 5 Click Close to return to the Privacy screen. 6 Click Apply to save this setting. 12.9.2 JavaScripts If pages of the web configurator do not display properly in Internet Explorer, check that JavaScripts are allowed. 1 In Internet Explorer, click Tools, Internet Options and then the Security tab.
P-2002 Series User’s Guide Figure 48 Internet Options 2 Click the Custom Level... button. 3 Scroll down to Scripting. 4 Under Active scripting make sure that Enable is selected (the default). 5 Under Scripting of Java applets make sure that Enable is selected (the default). 6 Click OK to close the window.
P-2002 Series User’s Guide Figure 49 Security Settings - Java Scripting 12.9.3 Java Permissions 1 From Internet Explorer, click Tools, Internet Options and then the Security tab. 2 Click the Custom Level... button. 3 Scroll down to Microsoft VM. 4 Under Java permissions make sure that a safety level is selected. 5 Click OK to close the window.
P-2002 Series User’s Guide Figure 50 Security Settings - Java 12.9.3.1 JAVA (Sun) 1 From Internet Explorer, click Tools, Internet Options and then the Advanced tab. 2 make sure that Use Java 2 for
P-2002 Series User’s Guide Figure 51 Java (Sun) 106 Chapter 12 Troubleshooting
P-2002 Series User’s Guide APPENDIX A Product Specifications See also the introduction chapter for a general overview of the key features. Specification Tables Table 41 Device Specifications Default Management IP Address 192.168.5.1 Default Management Subnet Mask 255.255.255.
P-2002 Series User’s Guide Table 42 Feature Specifications 108 Voice Functions SIP (RFC 3261) version 2 SDP (RFC 2327) RTP (RFC 1889) RTCP (RFC 1890) G.168 Echo Cancellation VAD (Voice Activity Detection) Silence Suppression CNG (Comfort Noise Generation) VLAN tag support QoS Supports TOS and Diffserv Tagging RTP Voice Highest Priority Codec: G.711 (PCM), G.
P-2002 Series User’s Guide Table 42 Feature Specifications (continued) Protocol Support PPP over Ethernet (RFC 2516) Transparent bridging for unsupported network layer protocols DHCP Client Management Embedded Web Configurator CLI (Command Line Interpreter) Remote Management via Telnet or Web SNMP manageable FTP/TFTP for firmware downloading, configuration backup and restoration Syslog Built-in Diagnostic Tools for FLASH memory, RAM and LAN port Static Routes 16 IP and 4 Bridge Hardware Features Rest
P-2002 Series User’s Guide Table 43 Power Adaptor Specifications (continued) NORTH AMERICAN PLUG STANDARDS AC Power Adapter Model AA-121A25 Input Power AC120Volts/60Hz/19W Output Power AC 12Volts/ 1.25A Power Consumption 14W Safety Standards UL, CUL (UL 1310, CSA C22.2 No.223) EUROPEAN PLUG STANDARDS AC Power Adapter Model AA-121A3BN Input Power AC230Volts/50Hz/140mA Output Power AC12Volts/1.
P-2002 Series User’s Guide APPENDIX B Setting up Your Computer’s IP Address All computers must have a 10M or 100M Ethernet adapter card and TCP/IP installed. Windows 95/98/Me/NT/2000/XP, Macintosh OS 7 and later operating systems and all versions of UNIX/LINUX include the software components you need to install and use TCP/ IP on your computer. Windows 3.1 requires the purchase of a third-party TCP/IP application package.
P-2002 Series User’s Guide Figure 52 WIndows 95/98/Me: Network: Configuration Installing Components The Network window Configuration tab displays a list of installed components. You need a network adapter, the TCP/IP protocol and Client for Microsoft Networks. If you need the adapter: 1 In the Network window, click Add. 2 Select Adapter and then click Add. 3 Select the manufacturer and model of your network adapter and then click OK. If you need TCP/IP: 1 In the Network window, click Add.
P-2002 Series User’s Guide 3 Select Microsoft from the list of manufacturers. 4 Select Client for Microsoft Networks from the list of network clients and then click OK. 5 Restart your computer so the changes you made take effect. Configuring 1 In the Network window Configuration tab, select your network adapter's TCP/IP entry and click Properties 2 Click the IP Address tab. • • If your IP address is dynamic, select Obtain an IP address automatically.
P-2002 Series User’s Guide Figure 54 Windows 95/98/Me: TCP/IP Properties: DNS Configuration 4 Click the Gateway tab. • • If you do not know your gateway’s IP address, remove previously installed gateways. If you have a gateway IP address, type it in the New gateway field and click Add. 5 Click OK to save and close the TCP/IP Properties window. 6 Click OK to close the Network window. Insert the Windows CD if prompted. 7 Turn on your Prestige and restart your computer when prompted.
P-2002 Series User’s Guide Figure 55 Windows XP: Start Menu 2 In the Control Panel, double-click Network Connections (Network and Dial-up Connections in Windows 2000/NT). Figure 56 Windows XP: Control Panel 3 Right-click Local Area Connection and then click Properties.
P-2002 Series User’s Guide Figure 57 Windows XP: Control Panel: Network Connections: Properties 4 Select Internet Protocol (TCP/IP) (under the General tab in Win XP) and then click Properties. Figure 58 Windows XP: Local Area Connection Properties 5 The Internet Protocol TCP/IP Properties window opens (the General tab in Windows XP). • 116 If you have a dynamic IP address click Obtain an IP address automatically.
P-2002 Series User’s Guide • • If you have a static IP address click Use the following IP Address and fill in the IP address, Subnet mask, and Default gateway fields. Click Advanced. Figure 59 Windows XP: Internet Protocol (TCP/IP) Properties 6 If you do not know your gateway's IP address, remove any previously installed gateways in the IP Settings tab and click OK.
P-2002 Series User’s Guide Figure 60 Windows XP: Advanced TCP/IP Properties 7 In the Internet Protocol TCP/IP Properties window (the General tab in Windows XP): • • Click Obtain DNS server address automatically if you do not know your DNS server IP address(es). If you know your DNS server IP address(es), click Use the following DNS server addresses, and type them in the Preferred DNS server and Alternate DNS server fields.
P-2002 Series User’s Guide Figure 61 Windows XP: Internet Protocol (TCP/IP) Properties 8 Click OK to close the Internet Protocol (TCP/IP) Properties window. 9 Click Close (OK in Windows 2000/NT) to close the Local Area Connection Properties window. 10 Close the Network Connections window (Network and Dial-up Connections in Windows 2000/NT). 11Turn on your Prestige and restart your computer (if prompted). Verifying Settings 1 Click Start, All Programs, Accessories and then Command Prompt.
P-2002 Series User’s Guide Figure 62 Macintosh OS 8/9: Apple Menu 2 Select Ethernet built-in from the Connect via list. Figure 63 Macintosh OS 8/9: TCP/IP 3 For dynamically assigned settings, select Using DHCP Server from the Configure: list.
P-2002 Series User’s Guide 4 For statically assigned settings, do the following: • • • • From the Configure box, select Manually. Type your IP address in the IP Address box. Type your subnet mask in the Subnet mask box. Type the IP address of your Prestige in the Router address box. 5 Close the TCP/IP Control Panel. 6 Click Save if prompted, to save changes to your configuration. 7 Turn on your Prestige and restart your computer (if prompted).
P-2002 Series User’s Guide Figure 65 Macintosh OS X: Network 4 For statically assigned settings, do the following: • • • • From the Configure box, select Manually. Type your IP address in the IP Address box. Type your subnet mask in the Subnet mask box. Type the IP address of your Prestige in the Router address box. 5 Click Apply Now and close the window. 6 Turn on your Prestige and restart your computer (if prompted). Verifying Settings Check your TCP/IP properties in the Network window.
P-2002 Series User’s Guide APPENDIX C IP Subnetting IP Addressing Routers “route” based on the network number. The router that delivers the data packet to the correct destination host uses the host ID. IP Classes An IP address is made up of four octets (eight bits), written in dotted decimal notation, for example, 192.168.1.1. IP addresses are categorized into different classes. The class of an address depends on the value of its first octet. • Class “A” addresses have a 0 in the left most bit.
P-2002 Series User’s Guide Since the first octet of a class “A” IP address must contain a “0”, the first octet of a class “A” address can have a value of 0 to 127. Similarly the first octet of a class “B” must begin with “10”, therefore the first octet of a class “B” address has a valid range of 128 to 191. The first octet of a class “C” address begins with “110”, and therefore has a range of 192 to 223.
P-2002 Series User’s Guide Since the mask is always a continuous number of ones beginning from the left, followed by a continuous number of zeros for the remainder of the 32 bit mask, you can simply specify the number of ones instead of writing the value of each octet. This is usually specified by writing a “/” followed by the number of bits in the mask after the address. For example, 192.1.1.0 /25 is equivalent to saying 192.1.1.0 with mask 255.255.255.128.
P-2002 Series User’s Guide Note: In the following charts, shaded/bolded last octet bit values indicate host ID bits “borrowed” to form network ID bits. The number of “borrowed” host ID bits determines the number of subnets you can have. The remaining number of host ID bits (after “borrowing”) determines the number of hosts you can have on each subnet. Table 49 Subnet 1 IP/SUBNET MASK NETWORK NUMBER LAST OCTET BIT VALUE IP Address 192.168.1. 0 IP Address (Binary) 11000000.10101000.00000001.
P-2002 Series User’s Guide Example: Four Subnets The above example illustrated using a 25-bit subnet mask to divide a class “C” address space into two subnets. Similarly to divide a class “C” address into four subnets, you need to “borrow” two host ID bits to give four possible combinations of 00, 01, 10 and 11. The subnet mask is 26 bits (11111111.11111111.11111111.11000000) or 255.255.255.192.
P-2002 Series User’s Guide Table 54 Subnet 4 IP/SUBNET MASK NETWORK NUMBER LAST OCTET BIT VALUE IP Address 192.168.1. 192 IP Address (Binary) 11000000.10101000.00000001. 11000000 Subnet Mask (Binary) 11111111.11111111.11111111. 11000000 Subnet Address: 192.168.1.192 Lowest Host ID: 192.168.1.193 Broadcast Address: 192.168.1.255 Highest Host ID: 192.168.1.254 Example Eight Subnets Similarly use a 27-bit mask to create 8 subnets (001, 010, 011, 100, 101, 110).
P-2002 Series User’s Guide Subnetting With Class A and Class B Networks. For class “A” and class “B” addresses the subnet mask also determines which bits are part of the network number and which are part of the host ID. A class “B” address has two host ID octets available for subnetting and a class “A” address has three host ID octets (see Table 44 on page 123) available for subnetting. The following table is a summary for class “B” subnet planning. Table 57 Class B Subnet Planning Appendix C NO.
P-2002 Series User’s Guide 130 Appendix C
P-2002 Series User’s Guide APPENDIX D PPPoE PPPoE in Action An ADSL modem bridges a PPP session over Ethernet (PPP over Ethernet, RFC 2516) from your computer to an ATM PVC (Permanent Virtual Circuit) which connects to a DSL Access Concentrator where the PPP session terminates (see Figure 66 on page 132). One PVC can support any number of PPP sessions from your LAN. PPPoE provides access control and billing functionality in a manner similar to dial-up services using PPP.
P-2002 Series User’s Guide Figure 66 Single-Computer per Router Hardware Configuration How PPPoE Works The PPPoE driver makes the Ethernet appear as a serial link to the computer and the computer runs PPP over it, while the modem bridges the Ethernet frames to the Access Concentrator (AC). Between the AC and an ISP, the AC is acting as a L2TP (Layer 2 Tunneling Protocol) LAC (L2TP Access Concentrator) and tunnels the PPP frames to the ISP. The L2TP tunnel is capable of carrying multiple PPP sessions.
P-2002 Series User’s Guide APPENDIX E Internal SPTGEN Internal SPTGEN Overview Internal SPTGEN (System Parameter Table Generator) is a configuration text file useful for efficient configuration of multiple Prestiges. Internal SPTGEN lets you configure, save and upload multiple menus at the same time using just one configuration text file – eliminating the need to configure each Prestige.
P-2002 Series User’s Guide If you enter a parameter that is invalid in the Input column, the Prestige will not save the configuration and the command line will display the Field Identification Number. Figure 69 on page 134, shown next, is an example of what the Prestige displays if you enter a value other than “0” or “1” in the Input column of Field Identification Number 1000000 (refer to Figure 68 on page 133).
P-2002 Series User’s Guide Figure 71 Internal SPTGEN FTP Download Example c:\ftp 192.168.1.1 220 PPP FTP version 1.0 ready at Sat Jan 1 03:22:12 2000 User (192.168.1.1:(none)): 331 Enter PASS command Password: 230 Logged in ftp>bin 200 Type I OK ftp> get rom-t ftp>bye c:\edit rom-t (edit the rom-t text file by a text editor and save it) Note: You can rename your “rom-t” file when you save it to your computer but it must be named “rom-t” when you upload it to your Prestige.
P-2002 Series User’s Guide Table 58 Abbreviations Used in the Example Internal SPTGEN Screens Table ABBREVIATION MEANING FIN Field Identification Number (not seen in SMT screens) FN Field Name PVA Parameter Values Allowed INPUT An example of what you may enter * Applies to the Prestige. The following are Internal SPTGEN screens associated with the SMT screens of your Prestige.
P-2002 Series User’s Guide Table 60 Menu 4 Internet Access Setup (continued) 40000002 = Active 40000003 = ISP's Name 40000004 = Encapsulation <2(PPPOE) | 3(RFC 1483)| 4(PPPoA )| 5(ENET ENCAP)> = 2 40000008 = Service Name = any 40000009 = My Login = test@pqa 40000010 = My Password = 1234 40000011 = Single User Account <0(No) | 1(Yes)> = 1 40000012 = IP Address Assignment <0(Static)|1(D = 1 ynamic)> 40000013 = IP Address = 0.0.0.
P-2002 Series User’s Guide Table 61 Menu 12 / Menu 12.1.1 IP Static Route Setup FIN FN PVA INPUT 120101001 = IP Static Route set #1, Name = 120101002 = IP Static Route set #1, Active <0(No) |1(Yes)> = 0 120101003 = IP Static Route set #1, Destination IP address = 0.0.0.0 120101004 = IP Static Route set #1, Destination IP subnetmask = 0 120101005 = IP Static Route set #1, Gateway = 0.0.0.
P-2002 Series User’s Guide Table 61 Menu 12 (continued) 120104004 = IP Static Route set #4, Destination IP subnetmask = 0 120104005 = IP Static Route set #4, Gateway = 0.0.0.0 120104006 = IP Static Route set #4, Metric = 0 120104007 = IP Static Route set #4, Private <0(No) |1(Yes)> = 0 / Menu 12.1.
P-2002 Series User’s Guide Table 61 Menu 12 (continued) 120108002 = IP Static Route set #8, Active <0(No) |1(Yes)> 120108003 = IP Static Route set #8, Destination IP address = 0.0.0.0 120108004 = IP Static Route set #8, Destination IP subnetmask = 0 120108005 = IP Static Route set #8, Gateway = 0.0.0.
P-2002 Series User’s Guide Table 62 Menu 15 SUA Server Setup (continued) 150000023 = SUA Server #6 Protocol 150000024 = SUA Server #6 Port Start = 0 150000025 = SUA Server #6 Port End = 0 150000026 = SUA Server #6 Local IP address = 0.0.0.0 150000027 = SUA Server #7 Active <0(No) | 1(Yes)> = 0 150000028 = SUA Server #7 Protocol <0(All)|6(TCP)|17(U DP)> = 0.0.0.
P-2002 Series User’s Guide Table 63 Menu 21.1 Filter Set #1 / Menu 21 Filter set #1 FIN FN PVA INPUT 210100001 = Filter Set 1, Name = / Menu 21.1.1.1 set #1, rule #1 FIN FN PVA INPUT 210101001 = IP Filter Set 1,Rule 1 Type <2(TCP/IP)> = 2 210101002 = IP Filter Set 1,Rule 1 Active <0(No)|1(Yes)> = 1 210101003 = IP Filter Set 1,Rule 1 Protocol = 6 210101004 = IP Filter Set 1,Rule 1 Dest IP address = 0.0.0.
P-2002 Series User’s Guide Table 63 Menu 21.1 Filter Set #1 (continued) 210102009 = IP Filter Set 1,Rule 2 Src Subnet Mask = 0 210102010 = IP Filter Set 1,Rule 2 Src Port = 0 210102011 = IP Filter Set 1,Rule 2 Src Port Comp <0(none)|1(equal) |2(not equal)|3(less)|4( greater)> = 0 210102013 = IP Filter Set 1,Rule 2 Act Match <1(check next)|2(forward)| 3(drop)> = 3 210102014 = IP Filter Set 1,Rule 2 Act Not Match <1(check next)|2(forward)| 3(drop)> = 1 / Menu 21.1.1.
P-2002 Series User’s Guide Table 63 Menu 21.1 Filter Set #1 (continued) 210104006 = IP Filter Set 1,Rule 4 Dest Port = 137 210104007 = IP Filter Set 1,Rule 4 Dest Port Comp 210104008 = IP Filter Set 1,Rule 4 Src IP address = 0.0.0.
P-2002 Series User’s Guide Table 63 Menu 21.1 Filter Set #1 (continued) 210106001 = IP Filter Set 1,Rule 6 Type <2(TCP/IP)> = 2 210106002 = IP Filter Set 1,Rule 6 Active <0(No)|1(Yes)> = 1 210106003 = IP Filter Set 1,Rule 6 Protocol = 17 210106004 = IP Filter Set 1,Rule 6 Dest IP address = 0.0.0.
P-2002 Series User’s Guide Table 64 Menu 21.1 Filer Set #2 (continued) 210201007 = IP Filter Set 2, Rule 1 Dest Port Comp <0(none)|1(equal)|2 = 1 (not equal)|3(less)|4(gr eater)> 210201008 = IP Filter Set 2, Rule 1 Src IP address = 0.0.0.
P-2002 Series User’s Guide Table 64 Menu 21.1 Filer Set #2 (continued) 210202014 = IP Filter Set 2, Rule 2 Act Not Match <1(check = 1 next)|2(forward)|3( drop)> / Menu 21.1.2.3 Filter set #2, rule #3 FIN FN PVA INPUT 210203001 = IP Filter Set 2, Rule 3 Type <0(none)|2(TCP/IP)> = 2 210203002 = IP Filter Set 2, Rule 3 Active <0(No)|1(Yes)> 210203003 = IP Filter Set 2, Rule 3 Protocol = 6 210203004 = IP Filter Set 2, Rule 3 Dest IP address = 0.0.0.
P-2002 Series User’s Guide Table 64 Menu 21.1 Filer Set #2 (continued) 210204007 = IP Filter Set 2, Rule 4 Dest Port Comp <0(none)|1(equal)|2 = 1 (not equal)|3(less)|4(gr eater)> 210204008 = IP Filter Set 2, Rule 4 Src IP address = 0.0.0.
P-2002 Series User’s Guide Table 64 Menu 21.1 Filer Set #2 (continued) 210205014 = IP Filter Set 2, Rule 5 Act Not Match <1(check = 1 next)|2(forward)|3( drop)> / Menu 21.1.2.6 Filter set #2, rule #6 FIN FN PVA INPUT 210206001 = IP Filter Set 2, Rule 6 Type <0(none)|2(TCP/IP)> = 2 210206002 = IP Filter Set 2, Rule 6 Active <0(No)|1(Yes)> 210206003 = IP Filter Set 2, Rule 6 Protocol = 17 210206004 = IP Filter Set 2, Rule 6 Dest IP address = 0.0.0.
P-2002 Series User’s Guide Table 65 Menu 23 System Menus (continued) FIN FN 230000000 = System Password PVA INPUT = 1234 Table 66 Menu 24.10 Time and Date Setting / Menu 24.
P-2002 Series User’s Guide Table 67 Menu 24.11 Remote Management Control (continued) 241100014 = DNS Service Access 241100015 = DNS Service Secured IP address <0(all)|1(none)|2(L = 0 an)|3(Wan)> = 0.0.0.0 Table 68 Menu 98 VoIP and Auto Upgrade Menus / Menu 98.1.
P-2002 Series User’s Guide Table 68 Menu 98 VoIP and Auto Upgrade Menus (continued) 980101022 = SIP #1 DTMF Key Type <0(RFC_2833) = 0 |1(PCM) |2(SIP_INFO) |3(RFC_2833_LIKE_SI P_INFO)> 980101023 = SIP #1 Transport Type <0(UDP) |1(TCP)> = 0 980101024 = SIP #1 Hide Caller ID <0(No) |1(Yes)> = 0 980101025 = SIP #1 Auto Redial 980101026 = SIP #1 STUN Server Active 980101027 = SIP #1 STUN Server Address 980101028 = SIP #1 STUN Server Port <1024~65535> = 0 980101029 = SIP #1 Call Forward Inde
P-2002 Series User’s Guide Table 68 Menu 98 VoIP and Auto Upgrade Menus (continued) 980102017 = SIP #2 Domain Name = sipserver.
P-2002 Series User’s Guide Table 68 Menu 98 VoIP and Auto Upgrade Menus (continued) 980301006 = Phone #1 Voice Active Detection Support <0(No) |1(Yes)> = 0 980301007 = Phone #1 Dialing Short Interval = 3 980301008 = Phone #1 Dialing Long Interval = 8 980301009 = Phone #1 Flash Max Interval = 1000 980301010 = Phone #1 Flash Min Interval = 100 / Menu 98.3.
P-2002 Series User’s Guide Table 68 Menu 98 VoIP and Auto Upgrade Menus (continued) / Menu 98.7.1 Phone Book (Speed Dial) #1 Setup FIN FN PVA INPUT 980701001 = Phone Book #1 Active <0(No) |1(Yes)> = 0 980701002 = Phone Book #1 SIP Number = 980701003 = Phone Book #1 SIP IP/URL = 980701004 = Phone Book #1 Name = 980701005 = Phone Book #1 Type 980701006 = Phone Book #1 Speed Number <0(Proxy) |1(NonProxy)> = 0 = / Menu 98.7.
P-2002 Series User’s Guide Table 68 Menu 98 VoIP and Auto Upgrade Menus (continued) 980705003 = Phone Book #5 SIP IP/URL = 980705004 = Phone Book #5 Name = 980705005 = Phone Book #5 Type 980705006 = Phone Book #5 Speed Number <0(Proxy) |1(NonProxy)> = 0 = / Menu 98.7.
P-2002 Series User’s Guide Table 68 Menu 98 VoIP and Auto Upgrade Menus (continued) / Menu 98.7.10 Phone Book (Speed Dial) #10 Setup FIN FN PVA INPUT 980710001 = Phone Book #10 Active <0(No) |1(Yes)> = 0 980710002 = Phone Book #10 SIP Number = 980710003 = Phone Book #10 SIP IP/URL = 980710004 = Phone Book #10 Name = 980710005 = Phone Book #10 Type 980710006 = Phone Book #10 Speed Number <0(Proxy) |1(NonProxy)> = 0 = / Menu 98.
P-2002 Series User’s Guide Table 68 Menu 98 VoIP and Auto Upgrade Menus (continued) 981101011 = Call Forward #1 Table[3] caller = 981101012 = Call Forward #1 Table[3] dest = 981101013 = Call Forward #1 Table[3] flag = 0 981101014 = Call Forward #1 Table[4] caller = 981101015 = Call Forward #1 Table[4] dest = 981101016 = Call Forward #1 Table[4] flag = 0 981101017 = Call Forward #1 Table[5] caller = 981101018 = Call Forward #1 Table[5] dest = 981101019 = Call Forward #1 Table[5] flag
P-2002 Series User’s Guide Table 68 Menu 98 VoIP and Auto Upgrade Menus (continued) 981102014 = Call Forward #2 Table[4] caller = 981102015 = Call Forward #2 Table[4] dest = 981102016 = Call Forward #2 Table[4] flag = 0 981102017 = Call Forward #2 Table[5] caller = 981102018 = Call Forward #2 Table[5] dest = 981102019 = Call Forward #2 Table[5] flag = 0 981102020 = Call Forward #2 Table[6] caller = 981102021 = Call Forward #2 Table[6] dest = 981102022 = Call Forward #2 Table[6] flag
P-2002 Series User’s Guide 160 Appendix E
P-2002 Series User’s Guide Index Numerics B 110V AC 6 230V AC 6 64kbps 62 8kbps 62 Backup Configuration 89 Basement 6 Block 79 Busy 79 BYE Request 46 A Abnormal Working Conditions 7 AbS 55 AC 6 Accept 79 Accessories 6 ACK Message 46 Acts of God 7 Administrator Inactivity Timer 36 ADPCM 108 Advanced Setup Call Forwarding 79 Airflow 6 ALG 53 Alternative Subnet Mask Notation 125 American Wire Gauge 6 Analog Telephone Adaptor 23 Analysis-by-Synthesis 55 Application Layer Gateway 53 ATA 23 Authentication Pa
P-2002 Series User’s Guide Contact Information 8 Contacting Customer Support 8 Copyright 3 Correcting Interference 4 Corrosive Liquids 6 CoS 64 Covers 6 Customer Support 8 D Damage 6 Dampness 6 Danger 6 Date 38 Daylight Savings 39 Dealer 4 Deep 107 Default Management IP Address 107 Default Management Subnet Mask 107 Default Password 30, 107 Defective 7 Denmark, Contact Information 8 DHCP 35 DHCP Client 109 DHCP Clients 35 Diagnostic Tools 109 Dialing Interval 68 Dialing Type 108 Differentiated Services 65
P-2002 Series User’s Guide Flashing 69 Foreign Exchange Office 107 Foreign Exchange Station 107 Forward to Number 79 France, Contact Information 8 FSM Logs 84 FTP 109 Full Cone NAT 50 Functionally Equivalent 7 FXO 107 FXS 107 G G.168 67 G.168 Active 68 G.168 Echo Cancellation 108 G.711 24, 55, 62, 108 G.
P-2002 Series User’s Guide Lifeline 23, 24, 75, 108 Lifeline Logs 84 Lifeline Screen 80 Lightning 6 LINE Port 24 Line Ports 107 Liquids, Corrosive 6 Listening Port 58, 63 Listening Volume 68 Log Message Descriptions 82 Logs 81 Loop Start Signaling 108 M Maintenance 85 Management 109 Management IP Address 29 Management IP Address, Default 107 Management Subnet Mask, Default 107 Manual Firmware Upgrades 25 Materials 7 Merchantability 7 Message Waiting Indication 55, 63 MGNT Port 86 Mgnt Port Screen 44 Min-S
P-2002 Series User’s Guide PHONE 1 and 2 Ports 59, 73 Phone Book 75 Phone Common Screen 73 Phone Port Screen 68 Phone Port Settings 68, 73, 79 Phone Ports 107 Phone Settings. 67 Photocopying 3 Point to Point Calling 108 Point to Point Calls 27 Point-to-Point Protocol over Ethernet 42 Polarity Reversal 108 Pool 6 Pop-up Blockers 99 Pop-up Blocking 29 Pop-up Windows 99 Port 48 Port Restricted Cone NAT 52 Postage Prepaid.
P-2002 Series User’s Guide RFC 1889 48, 108 RFC 1890 108 RFC 2327 108 RFC 2516 109 RFC 3261 108 RFC 3489 54 RFC 3842 55 RFC 867 38 RFC 868 38 RFC3489 108 Rights 3 Rights, Legal 7 Ringer Equivalence Number 24 Ringing Voltage 107 Risk 6 Risks 6 RJ-45 107 RMA 7 RTCP (RFC 1890) 108 RTP 48 RTP (RFC 1889) 108 RTP Logs 83 RTP Port Range 62 S Safety Warnings 6 SDP (RFC 2327) 108 Separation Between Equipment and Receiver 4 Serial Number 8 Server 38 Server, Outbound Proxy 54 Service 6, 7 Service Pack 2 99 Service P
P-2002 Series User’s Guide T V Table Number 79 Tampering 7 Telecommunication Line Cord.
P-2002 Series User’s Guide Z ZyNOS 3 ZyNOS Firmware Version 86 ZyXEL Communications Corporation 3 ZyXEL Home Page 4 ZyXEL Limited Warranty Note 7 ZyXEL Network Operating System 3 168 Index
