P-660H/HW-D Series User’s Guide 197 Chapter 13 Bandwidth Management
P-660H/HW-D Series User’s Guide CHAPTER 14 Dynamic DNS Setup This chapter discusses how to configure your ZyXEL Device to use Dynamic DNS. 14.1 Dynamic DNS Overview Dynamic DNS allows you to update your current dynamic IP address with one or many dynamic DNS services so that anyone can contact you (in NetMeeting, CU-SeeMe, etc.). You can also access your FTP server or Web site on your own computer using a domain name (for instance myhost.dhs.
P-660H/HW-D Series User’s Guide Figure 109 Dynamic DNS The following table describes the fields in this screen. Table 79 Dynamic DNS LABEL DESCRIPTION Dynamic DNS Setup Active Dynamic DNS Select this check box to use dynamic DNS. Service Provider This is the name of your Dynamic DNS service provider. Dynamic DNS Type Select the type of service that you are registered for from your Dynamic DNS service provider.
P-660H/HW-D Series User’s Guide Table 79 Dynamic DNS (continued) LABEL DESCRIPTION Dynamic DNS server auto detect IP Address Select this option only when there are one or more NAT routers between the ZyXEL Device and the DDNS server. This feature has the DDNS server automatically detect and use the IP address of the NAT router that has a public IP address. Note: The DDNS server may not be able to detect the proper IP address if there is an HTTP proxy server between the ZyXEL Device and the DDNS server.
P-660H/HW-D Series User’s Guide 201 Chapter 14 Dynamic DNS Setup
P-660H/HW-D Series User’s Guide CHAPTER 15 Remote Management Configuration This chapter provides information on configuring remote management. 15.1 Remote Management Overview Remote management allows you to determine which services/protocols can access which ZyXEL Device interface (if any) from which computers. Note: When you configure remote management to allow management from the WAN, you still need to configure a firewall rule to allow access.
P-660H/HW-D Series User’s Guide • The IP address in the Secured Client IP field does not match the client IP address. If it does not match, the ZyXEL Device will disconnect the session immediately. • There is already another remote management session with an equal or higher priority running. You may only have one remote management session running at one time. • There is a firewall rule that blocks it. 15.1.
P-660H/HW-D Series User’s Guide The following table describes the labels in this screen. Table 80 Remote Management: WWW LABEL DESCRIPTION Port You may change the server port number for a service if needed, however you must use the same port number in order to use that service for remote management. Access Status Select the interface(s) through which a computer may access the ZyXEL Device using this service.
P-660H/HW-D Series User’s Guide Figure 112 Remote Management: Telnet The following table describes the labels in this screen. Table 81 Remote Management: Telnet LABEL DESCRIPTION Port You may change the server port number for a service if needed, however you must use the same port number in order to use that service for remote management. Access Status Select the interface(s) through which a computer may access the ZyXEL Device using this service.
P-660H/HW-D Series User’s Guide Figure 113 Remote Management: FTP The following table describes the labels in this screen. Table 82 Remote Management: FTP LABEL DESCRIPTION Port You may change the server port number for a service if needed, however you must use the same port number in order to use that service for remote management. Access Status Select the interface(s) through which a computer may access the ZyXEL Device using this service.
P-660H/HW-D Series User’s Guide Figure 114 SNMP Management Model An SNMP managed network consists of two main types of component: agents and a manager. An agent is a management software module that resides in a managed device (the ZyXEL Device). An agent translates the local management information from the managed device into a form compatible with SNMP. The manager is the console through which network administrators perform network management functions.
P-660H/HW-D Series User’s Guide 15.6.2 SNMP Traps The ZyXEL Device will send traps to the SNMP manager when any one of the following events occurs: Table 83 SNMP Traps TRAP NAME DESCRIPTION 0 coldStart (defined in RFC-1215) A trap is sent after booting (power on). 1 warmStart (defined in RFC-1215) A trap is sent after booting (software reboot). 6 whyReboot (defined in ZYXELMIB) A trap is sent with the reason of restart before rebooting when the system is going to restart (warm start).
P-660H/HW-D Series User’s Guide The following table describes the labels in this screen. Table 84 Remote Management: SNMP LABEL DESCRIPTION SNMP Port You may change the server port number for a service if needed, however you must use the same port number in order to use that service for remote management. Access Status Select the interface(s) through which a computer may access the ZyXEL Device using this service.
P-660H/HW-D Series User’s Guide Figure 116 Remote Management: DNS The following table describes the labels in this screen. Table 85 Remote Management: DNS LABEL DESCRIPTION Port The DNS service port number is 53. Access Status Select the interface(s) through which a computer may send DNS queries to the ZyXEL Device. Secured Client IP A secured client is a “trusted” computer that is allowed to send DNS queries to the ZyXEL Device.
P-660H/HW-D Series User’s Guide Figure 117 Remote Management: ICMP The following table describes the labels in this screen. Table 86 Remote Management: ICMP LABEL DESCRIPTION ICMP Internet Control Message Protocol is a message control and error-reporting protocol between a host server and a gateway to the Internet. ICMP uses Internet Protocol (IP) datagrams, but the messages are processed by the TCP/IP software and directly apparent to the application user.
P-660H/HW-D Series User’s Guide Follow the procedure below to configure your ZyXEL Device to be managed by CNM Access. See the Command Interpreter appendix for information on the command structure and how to access the CLI (Command Line Interface) on the ZyXEL Device. Note: In this example a.b.c.d is the IP address of CNM Access. You must change this value to reflect your actual management server IP address or domain name. See Table 87 on page 212 for detailed descriptions of the commands.
P-660H/HW-D Series User’s Guide 213 Chapter 15 Remote Management Configuration
P-660H/HW-D Series User’s Guide CHAPTER 16 Universal Plug-and-Play (UPnP) This chapter introduces the UPnP feature in the web configurator. 16.1 Introducing Universal Plug and Play Universal Plug and Play (UPnP) is a distributed, open networking standard that uses TCP/IP for simple peer-to-peer network connectivity between devices. A UPnP device can dynamically join a network, obtain an IP address, convey its capabilities and learn about other devices on the network.
P-660H/HW-D Series User’s Guide 16.1.3 Cautions with UPnP The automated nature of NAT traversal applications in establishing their own services and opening firewall ports may present network security issues. Network information and configuration may also be obtained and modified by users in some network environments. When a UPnP device joins a network, it announces its presence with a multicast message. For security reasons, the ZyXEL Device allows multicast messages on the LAN only.
P-660H/HW-D Series User’s Guide The following table describes the fields in this screen. Table 88 Configuring UPnP LABEL DESCRIPTION Active the Universal Plug and Select this check box to activate UPnP. Be aware that anyone could use Play (UPnP) Feature a UPnP application to open the web configurator's login screen without entering the ZyXEL Device's IP address (although you must still enter the password to access the web configurator).
P-660H/HW-D Series User’s Guide Figure 120 Add/Remove Programs: Windows Setup: Communication 3 In the Communications window, select the Universal Plug and Play check box in the Components selection box. Figure 121 Add/Remove Programs: Windows Setup: Communication: Components 4 Click OK to go back to the Add/Remove Programs Properties window and click Next. 5 Restart the computer when prompted.
P-660H/HW-D Series User’s Guide 16.3.2 Installing UPnP in Windows XP Follow the steps below to install the UPnP in Windows XP. 1 Click start and Control Panel. 2 Double-click Network Connections. 3 In the Network Connections window, click Advanced in the main menu and select Optional Networking Components …. Figure 122 Network Connections 4 The Windows Optional Networking Components Wizard window displays. Select Networking Service in the Components selection box and click Details.
P-660H/HW-D Series User’s Guide Figure 124 Networking Services 6 Click OK to go back to the Windows Optional Networking Component Wizard window and click Next. 16.4 Using UPnP in Windows XP Example This section shows you how to use the UPnP feature in Windows XP. You must already have UPnP installed in Windows XP and UPnP activated on the ZyXEL Device. Make sure the computer is connected to a LAN port of the ZyXEL Device. Turn on your computer and the ZyXEL Device. 16.4.
P-660H/HW-D Series User’s Guide Figure 125 Network Connections 3 In the Internet Connection Properties window, click Settings to see the port mappings there were automatically created. Figure 126 Internet Connection Properties 4 You may edit or delete the port mappings or click Add to manually add port mappings.
P-660H/HW-D Series User’s Guide Figure 127 Internet Connection Properties: Advanced Settings Figure 128 Internet Connection Properties: Advanced Settings: Add Note: When the UPnP-enabled device is disconnected from your computer, all port mappings will be deleted automatically. 5 Select Show icon in notification area when connected option and click OK. An icon displays in the system tray.
P-660H/HW-D Series User’s Guide 6 Double-click on the icon to display your current Internet connection status. Figure 130 Internet Connection Status 16.4.2 Web Configurator Easy Access With UPnP, you can access the web-based configurator on the ZyXEL Device without finding out the IP address of the ZyXEL Device first. This comes helpful if you do not know the IP address of the ZyXEL Device. Follow the steps below to access the web configurator. 1 Click Start and then Control Panel.
P-660H/HW-D Series User’s Guide Figure 131 Network Connections 4 An icon with the description for each UPnP-enabled device displays under Local Network. 5 Right-click on the icon for your ZyXEL Device and select Invoke. The web configurator login screen displays.
P-660H/HW-D Series User’s Guide Figure 132 Network Connections: My Network Places 6 Right-click on the icon for your ZyXEL Device and select Properties. A properties window displays with basic information about the ZyXEL Device.
P-660H/HW-D Series User’s Guide 225 Chapter 16 Universal Plug-and-Play (UPnP)
P-660H/HW-D Series User’s Guide CHAPTER 17 System Use this screen to configure the ZyXEL Device’s time and date settings. 17.1 General Setup 17.1.1 General Setup and System Name General Setup contains administrative and system-related information. System Name is for identification purposes. However, because some ISPs check this name you should enter your computer's "Computer Name". • In Windows 95/98 click Start, Settings, Control Panel, Network.
P-660H/HW-D Series User’s Guide Figure 134 System General Setup The following table describes the labels in this screen. Table 89 System General Setup LABEL DESCRIPTION General Setup System Name Choose a descriptive name for identification purposes. It is recommended you enter your computer’s “Computer name” in this field. This name can be up to 30 alphanumeric characters long. Spaces are not allowed, but dashes “-” and underscores "_" are accepted.
P-660H/HW-D Series User’s Guide Table 89 System General Setup LABEL DESCRIPTION Admin Password If you log in with the admin password, you can configure the advanced features as well as the wizard setup on the ZyXEL Device. Old Password Type the default admin password (1234) or the existing password you use to access the system for configuring advanced features. New Password Type your new system password (up to 30 characters).
P-660H/HW-D Series User’s Guide The following table describes the fields in this screen. Table 90 System Time Setting LABEL DESCRIPTION Current Time and Date Current Time This field displays the time of your ZyXEL Device. Each time you reload this page, the ZyXEL Device synchronizes the time with the time server. Current Date This field displays the date of your ZyXEL Device. Each time you reload this page, the ZyXEL Device synchronizes the date with the time server.
P-660H/HW-D Series User’s Guide Table 90 System Time Setting (continued) LABEL DESCRIPTION Start Date Configure the day and time when Daylight Saving Time starts if you selected Enable Daylight Saving. The o'clock field uses the 24 hour format. Here are a couple of examples: Daylight Saving Time starts in most parts of the United States on the first Sunday of April. Each time zone in the United States starts using Daylight Saving Time at 2 A.M. local time.
P-660H/HW-D Series User’s Guide 231 Chapter 17 System
P-660H/HW-D Series User’s Guide CHAPTER 18 Logs This chapter contains information about configuring general log settings and viewing the ZyXEL Device’s logs. Refer to the appendix for example log message explanations. 18.1 Logs Overview The web configurator allows you to choose which categories of events and/or alerts to have the ZyXEL Device log and then display the logs or have the ZyXEL Device send them to an administrator (as e-mail) or to a syslog server. 18.1.
P-660H/HW-D Series User’s Guide Figure 136 View Log The following table describes the fields in this screen. Table 91 View Log LABEL DESCRIPTION Display The categories that you select in the Log Settings screen display in the drop-down list box. Select a category of logs to view; select All Logs to view logs from all of the log categories that you selected in the Log Settings page. Time This field displays the time the log was recorded. Message This field states the reason for the log.
P-660H/HW-D Series User’s Guide Alerts are e-mailed as soon as they happen. Logs may be e-mailed as soon as the log is full. Selecting many alert and/or log categories (especially Access Control) may result in many emails being sent. Figure 137 Log Settings The following table describes the fields in this screen. Table 92 Log Settings LABEL DESCRIPTION E-mail Log Settings Mail Server Enter the server name or the IP address of the mail server for the e-mail addresses specified below.
P-660H/HW-D Series User’s Guide Table 92 Log Settings LABEL DESCRIPTION Send Log To The ZyXEL Device sends logs to the e-mail address specified in this field. If this field is left blank, the ZyXEL Device does not send logs via e-mail. Send Alerts To Alerts are real-time notifications that are sent as soon as an event, such as a DoS attack, system error, or forbidden web access attempt occurs. Enter the E-mail address where the alert messages will be sent.
