P-660H-T Series ADSL2+ 4-port Security Gateway P-660HW-T Series 802.11g Wireless ADSL2+ 4-port Security Gateway Quick Start Guide Version 3.
P-660HW-T and P-660H-T Series Quick Start Guide Overview The P-660HW-T is an ADSL Internet gateway with IEEE 802.11g wireless capability and a 4-port built-in switch. The P-660H-T is an ADSL Internet gateway with a 4-port built-in switch. You may need your Internet access information. Both model series are referred to as the “Prestige” in this guide. See your User’s Guide for background information on all features. This guide is divided into the following sections.
P-660HW-T and P-660H-T Series Quick Start Guide P-660H-T Series P-660HW-T Series 1 DSL: Connect the Prestige to a telephone jack using a telephone wire. 2 LAN: Use an Ethernet cable to connect a computer to a LAN 10/100M port for initial configuration and/or Internet access. 3 POWER: Use the included power adaptor to connect the POWER socket to an appropriate power source (see the User’s Guide for power adaptors specifications by region).
P-660HW-T and P-660H-T Series Quick Start Guide After you’ve made the connections, push in the power button to turn on the Prestige. Look at the front panel LEDs. The PWR/SYS LED blinks while performing system testing. The PWR/SYS and/or WLAN LEDs then turn steady on if the testing is successful. The LAN LED turns on if the LAN port is properly connected.
P-660HW-T and P-660H-T Series Quick Start Guide Note: If you do not see the next screen, then please read Section 6.1 on page 10 2 Click Login. 3 Type a new password (retype it to confirm) and click Apply. Otherwise click Ignore. You then see the main web configurator screen 4 In the MAIN MENU screen, click WIZARD SETUP. The P-660H-T main screen is the same as this P660HW-T one, but it does not have a wireless LAN link. 2.3.
P-660HW-T and P-660H-T Series Quick Start Guide 1 From the Mode drop-down list box, select Routing (default) if you want to use routing features such as NAT. 2 The next wizard screen varies depending on the Encapsulation you chose in the first wizard screen. From the Network Address Translation drop-down list box, select SUA Only if you have one public IP address, Full Feature if you have more than one public IP address (for translation) or None to disable NAT. • PPPoE.
P-660HW-T and P-660H-T Series Quick Start Guide Note: You will only see the next two screens in Routing mode. • PPPoA • RFC1483 3 Verify your LAN and WAN settings. 4 Click Save Settings in the screen shown in step 3 to go to the final wizard screen.The Prestige automatically tests the connection to the computer(s) connected to the LAN port. To test the connection from the Prestige to the ISP, click Start Diagnose. Otherwise click Return to Main Menu to go back to the main screen.
P-660HW-T and P-660H-T Series Quick Start Guide Note: Wireless clients and the Prestige must use the same SSID, channel ID, WEP or WPA-PSK key (if enabled). 1 Click the Wireless LAN link under Advanced Setup. 2 Click 802.1x/WPA. Select Authentication Required, then select WPAPSK and then type a Preshared Key. 3 Click Advanced Setup, Wireless LAN, Wireless. In the ESSID field, enter up to 32 printable characters to uniquely identify the Prestige.
P-660HW-T and P-660H-T Series Quick Start Guide Click Advanced Setup and then NAT to open the NAT-Mode screen. Select SUA Only if you have one public IP address and Full Feature if you have multiple public IP addresses (for address translation). If you have servers on your LAN, configure an SUA server set to have them visible to the outside. From the NAT Mode screen click Edit Details and fill in the fields as shown. 5 Firewall The firewall is already enabled by default on the Prestige.
P-660HW-T and P-660H-T Series Quick Start Guide 6 Troubleshooting PROBLEM CORRECTIVE ACTION None of the LEDs turn on when Make sure that you have the correct power adaptor connected to the Prestige, it you connect the Prestige’s is plugged into an appropriate power source and the Prestige is turned on. power. Check all cable connections. If the LEDs still do not turn on, you may have a hardware problem. In this case, you should contact your local vendor. Cannot access the Prestige from my computer.
P-660HW-T and P-660H-T Series Quick Start Guide 4 Select Internet Protocol (TCP/IP) (under the General tab in Windows XP) and click Properties. 5 The Internet Protocol TCP/IP Properties screen opens (the General tab in Windows XP). 6 Select the Obtain an IP address automatically and Obtain DNS server address automatically options. 7 Click OK to close the Internet Protocol (TCP/IP) Properties window. 8 Click Close (OK in Windows 2000/NT) to close the Local Area Connection Properties window.
