P-2302R Series VoIP Station Gateway Quick Start Guide Version 3.
P-2302R Series Overview This Quick Start Guide covers the Prestige (P-2302R) and (P-2302RL) models. It explains how to use your Prestige to make phone calls through the Internet. See your User’s Guide for more information on all features. The P-2302RL’s lifeline feature adds regular phone services (that do not use the Internet). The following figure shows your Prestige (A) connected to the modem or router that provides your Internet connection (B). C is your voice service provider.
P-2302R Series 2 Hardware Connections 1 LAN: Connect a computer or an Ethernet switch to this port with an Ethernet cable. 2 WAN: Connect a broadband modem or router to this port with an Ethernet cable. 3 LINE: (P-2302RL only). Use telephone wire to connect this port to the telephone jack. This is a FXO (Foreign Exchange Office) port. 4 Phone 1-2: Connect one or more analog telephones to these ports using telephone wire. These are FXS (Foreign Exchange Station) ports.
P-2302R Series 3 Initial Configuration In this section you will access your Prestige and configure it for Internet access and making phone calls through the Internet. Instructions are also provided for configuring the P-2302RL to make regular calls. 1 Launch your web browser. Enter “192.168.1.1” as the web site address. 2 Click Login. See Section 5.1 on page 10 if this screen does not open. 3 Type a new password (and retype it to confirm) and click Apply. Otherwise click Ignore.
P-2302R Series 3.1 General Setup (Optional) This screen is optional. You can just click Next. System Name is for identifying the Prestige. You can enter your computer's "Computer Name". Domain Name: Manually enter a domain name if you want to. You can also leave it blank or set to whatever may have displayed automatically. 3.2 Internet Access Setup If you were given Internet access settings, enter them in the fields. Otherwise leave the default settings and just click Next.
P-2302R Series 3.2.2 PPP over Ethernet If you are not using Ethernet encapsulation and are given a username and password, you are using PPP over Ethernet encapsulation. Enter the information provided. Select Nailed-Up Connection when you want your connection up all the time (this could be expensive if your ISP bills you for Internet usage time instead of a flat monthly fee). To not have the connection up all the time, specify an idle time-out period (in seconds) in Idle Timeout. 3.
P-2302R Series 3.4 SIP Account 1 Setup Note: You should have a voice account already set up. Fill in the fields with information from your voice service provider. Leave the default settings in fields for which no information was provided (except if otherwise specified). Note: This screen configures SIP account 1. See the User’s Guide for details on using the VoIP screens to configure SIP account 2. If you have a SIP account like 1234@VoIPprovider.com,“1234” would be the SIP Number and “VoIP-provider.
P-2302R Series 3.5 Speed Dial Configuration Click PHONE BOOK in the navigation panel and then Speed Dial. Speed dial provides shortcuts for dialing frequently used (VoIP) phone numbers. You can use speed dial entries for peer-topeer calls or SIP numbers that use letters. Select a speed dial key combination. Enter the SIP number of the party you will call and a name to identify them. Select Use Proxy if calls to this party use your SIP account.
P-2302R Series 3.6 Lifeline Configuration (P2302RL) Click PHONE BOOK in the navigation panel and then Lifeline. PSTN Pre-fix Number: If you want to make a regular call when the PWR/VoIP LED is orange, dial the prefix number that you configure here and the phone number. If the PWR/VoIP LED is green or off, make regular calls without a prefix number. Relay to PSTN: Enter phone numbers that should use the regular phone service (without the prefix number). Do this for emergency numbers.
P-2302R Series 5 Troubleshooting PROBLEM CORRECTIVE ACTION None of the LEDs turn Make sure that you have the correct power adaptor connected to the Prestige and an on when you connect appropriate power source. Make sure that the power source is turned on. Check all cable the Prestige’s power. connections. If the LEDs still do not turn on, you may have a hardware problem. In this case, you should contact your local vendor. Cannot access the Prestige from my computer.
P-2302R Series 4 Select Internet Protocol (TCP/IP) (under the General tab in Win XP) and click Properties. 5 The Internet Protocol TCP/IP Properties screen opens (the General tab in Windows XP). 6 Select the Obtain an IP address automatically and Obtain DNS server address automatically options. 7 Click OK to close the Internet Protocol (TCP/IP) Properties window. 8 Click Close (OK in Windows 2000/NT) to close the Local Area Connection Properties window. 9 Close the Network Connections screen.
