NBG2105 Wireless Mini Travel Router Version 1.00 Edition 1, 11/2012 Quick Start Guide User’s Guide Default Login Details LAN IP Address 192.168.1.1 (Router Mode) 192.168.1.2 (Other Modes) Password www.zyxel.
IMPORTANT! READ CAREFULLY BEFORE USE. KEEP THIS GUIDE FOR FUTURE REFERENCE. Screenshots and graphics in this book may differ slightly from your product due to differences in your product firmware or your computer operating system. Every effort has been made to ensure that the information in this manual is accurate. Related Documentation • Quick Start Guide The Quick Start Guide shows how to connect the NBG2105 and access the Web Configurator. It contains information on setting up your wireless network.
Contents Overview Contents Overview User’s Guide ....................................................................................................................................... 11 Introduction .............................................................................................................................................13 Introducing the Web Configurator ...........................................................................................................19 Operation Modes .......
Contents Overview 4 NBG2105 User’s Guide
Table of Contents Table of Contents Contents Overview ..............................................................................................................................3 Table of Contents .................................................................................................................................5 Part I: User’s Guide ......................................................................................... 11 Chapter 1 Introduction...........................................
Table of Contents 3.5.1 Setting Client Mode .................................................................................................................27 3.5.2 Navigation Panel .....................................................................................................................27 3.6 WISP + UR Mode ..............................................................................................................................29 3.6.1 Setting WISP + UR Mode ...............................
Table of Contents 7.2 Welcome Screen ...............................................................................................................................51 7.3 WAN Interface Setup ........................................................................................................................51 7.3.1 Static IP ...................................................................................................................................51 7.3.2 DHCP Client .............................
Table of Contents 10.4.3 PPPoE ...................................................................................................................................76 Chapter 11 Quality of Service (QoS).....................................................................................................................79 11.1 Overview .........................................................................................................................................79 11.2 QoS Setup Screen ..............
Table of Contents Chapter 15 Management......................................................................................................................................105 15.1 Overview .......................................................................................................................................105 15.2 What You Can Do .........................................................................................................................105 15.3 NTP Screen ...................
Table of Contents 10 NBG2105 User’s Guide
P ART I User’s Guide 11
C HAPT ER 1 Introduction 1.1 Overview This chapter introduces the main features and applications of the NBG2105. The NBG2105 extends the range of your existing wired network without additional wiring, providing easy network access to mobile users. You can set up a wireless network with other IEEE 802.11b/g/ n compatible devices. A range of services such as a firewall and content filtering are also available for secure Internet computing. 1.
Chapter 1 Introduction • Change the password. Use a password that’s not easy to guess and that consists of different types of characters, such as numbers and letters. • Write down the password and put it in a safe place. • Back up the configuration (and make sure you know how to restore it). Restoring an earlier working configuration may be useful if the device becomes unstable or even crashes. If you forget your password, you will have to reset the NBG2105 to its factory default settings.
Chapter 1 Introduction Note: You must activate WPS in the NBG2105 and in another wireless device within two minutes of each other. For more information on using WPS, see Section 8.2 on page 59. 1.7 The Clone MAC Button Your NBG2105 can clone the MAC address of the computer connected to the NBG2105. It is recommended that you clone the MAC address prior to hooking up the WAN port or connecting to an AP or wireless router with Internet access.
Chapter 1 Introduction 1.8 General Hardware Features Figure 1 General Hardware Features Micro USB LEDs WPS Ethernet Operation Mode Switch Clone MAC The following table describes the LEDs. Note: WPS is only available with WPA2-PSK security protocol. Table 1 General Hardware Features FEATURE DESCRIPTION Ethernet Connect this to your Ethernet network. LEDs These show the status of your NBG2105.
Chapter 1 Introduction Table 1 General Hardware Features (continued) FEATURE DESCRIPTION Operation Mode Switch Slide this to Router to put the NBG2105 into router or AP mode. Slide this to Client to put the NBG2105 into WLAN client mode. Slide this to WISP+UR to put the NBG2105 into WISP+UR mode. Clone MAC Push this for 2 to 5 seconds to clone the first client's MAC address. Push this for more than 5 seconds to reset the NBG2105’s MAC address to the factory default.
Chapter 1 Introduction Table 2 Top Panel LEDs (continued) LED COLOR STATUS DESCRIPTION WLAN Blue On The NBG2105 is ready, but is not sending/receiving data through the wireless LAN. Blinking The NBG2105 is sending/receiving data through the wireless LAN. Off WPS/MAC Clone Blue The wireless LAN is not ready, has failed, or is disabled. On WPS/MAC clone is ready. Blinking The NBG2105 is negotiating a WPS connection with a wireless client or cloning a MAC address.
C HAPT ER 2 Introducing the Web Configurator 2.1 Overview This chapter describes how to access the NBG2105 Web Configurator and provides an overview of its screens. The Web Configurator is an HTML-based management interface that allows easy setup and management of the NBG2105 via Internet browser. Use Internet Explorer 6.0 and later versions, Mozilla Firefox 3 and later versions, or Safari 2.0 and later versions. The recommended screen resolution is 1024 by 768 pixels.
Chapter 2 Introducing the Web Configurator 2 Launch your web browser. 3 The NBG2105 is in Router mode by default. Type "http://192.168.1.1" as the website address. If the NBG2105 isn’t in Router mode, the IP address is 192.168.1.2. See Chapter 3 on page 21 for more information about the modes of the NBG2105. Your computer must be in the same subnet in order to access this website address. 2.2.1 Login Screen The Web Configurator initially displays the following login screen.
C HAPT ER 3 Operation Modes 3.1 Overview This chapter introduces the operation modes available on your NBG2105 and how to configure them. The operation mode is a pre-defined combination of routing, access point (AP) and wireless client functions to match your network topology and requirements. Use the Operation Mode switch on the right-side panel (see Section 1.8 on page 16) of the NBG2105 to select the operation mode. Use the Router Operation Mode screen to configure the selected mode. 3.
Chapter 3 Operation Modes Figure 4 Router Mode Application 3.3.1 Setting Router Mode Select Router mode if your device routes traffic between a local network and another network such as the Internet. To set Router mode: 1 Make sure the power LED is on (not blinking). 2 Slide the Operation Mode Switch to Router. See Section 1.8 on page 16. 3 The NBG2105 restarts after you slide the Operation Mode Switch. 3.3.2 Navigation Panel Use the sub-menus on the navigation panel to configure NBG2105 features.
Chapter 3 Operation Modes Figure 5 Navigation Panel: Router Mode The following table describes the sub-menus. Table 5 Navigation Panel: Router Mode MENU FUNCTION Wizard The Web Configurator’s wizard setup helps you configure your device in router mode for the first time. Network LAN Use this to configure LAN IP address and subnet mask and DHCP server settings. WAN Use this allows you to configure ISP parameters, WAN IP address assignment, DNS servers and the WAN MAC address.
Chapter 3 Operation Modes Table 5 Navigation Panel: Router Mode (continued) MENU MAC Filtering FUNCTION Use this to allow or deny wireless stations based on their MAC addresses from connecting to the NBG2105. Firewall Port Filtering Use this to apply filtering based on UDP or TCP port numbers. IP Filtering Use this to apply filtering based on IP addresses. MAC Filtering Use this to apply filtering based on MAC addresses. URL Filtering Use this to apply filtering based on URLs.
Chapter 3 Operation Modes Figure 6 Access Point Mode Application 3.4.1 Setting Access Point Mode Select Access Point Mode if your device bridges traffic between clients on the same network. To set Access Point mode: 1 Make sure the power LED is on (not blinking). 2 Slide the Operation Mode Switch to Router. See Section 1.8 on page 16. 3 The NBG2105 restarts after you slide the Operation Mode Switch. 4 In the Web Configuator, click Management > Operation, select AP and then click Apply Changes. 3.
Chapter 3 Operation Modes Figure 7 Navigation Panel: Access Point Mode The following table describes the sub-menus. Table 6 Navigation Panel: Access Point Mode MENU FUNCTION Wizard The Web Configurator’s wizard setup helps you configure your device in AP mode for the first time. Network LAN Use this to configure LAN IP address and subnet mask and DHCP server settings. Wireless LAN Basic Use this to turn the wireless connection on or off and make other basic configuration changes.
Chapter 3 Operation Modes Table 6 Navigation Panel: Access Point Mode (continued) MENU FUNCTION Status Status Use this to view system, wireless, local and WAN network information, as well as general information about the NBG2105. Statistics Use this to show the number of packets sent and received on the Wireless LAN and Ethernet WAN interfaces. Log Use this to look at all of the NBG2105’s logs in one location. 3.
Chapter 3 Operation Modes Figure 9 Navigation Panel: Client Mode The following table describes the sub-menus. Table 7 Navigation Panel: Client Mode MENU FUNCTION Wizard The Web Configurator’s wizard setup helps you configure your device in client mode for the first time. Network LAN Use this to configure LAN IP address and subnet mask. Wireless LAN Site Survey Use this to scan for and connect to a wireless network automatically.
Chapter 3 Operation Modes 3.6 WISP + UR Mode In WISP (Wireless ISP) + UR (Universal Repeater) mode, your NBG2105 can act as a wireless client to wirelessly connect to the Internet or an existing network via an access point. In addition, it can provide Wi-Fi function to the clients on the LAN side. Use this mode if you want to wirelessly connect to the Internet or have an access point or wireless router in your network. In WISP + UR mode, the IP address of the device on the local network is 192.168.1.2.
Chapter 3 Operation Modes Figure 11 Navigation Panel: WISP+UR Mode The following table describes the sub-menus. Table 8 Navigation Panel: WISP+UR Mode MENU FUNCTION Wizard The Web Configurator’s wizard setup helps you configure your device in WISP+UR mode for the first time. Network LAN Use this to configure LAN IP address and subnet mask. WAN Use this allows you to configure ISP parameters, WAN IP address assignment, DNS servers and the WAN MAC address.
Chapter 3 Operation Modes Table 8 Navigation Panel: WISP+UR Mode (continued) MENU MAC Filtering FUNCTION Use this to allow or deny wireless stations based on their MAC addresses from connecting to the NBG2105. Firewall Port Filtering Use this to apply filtering based on UDP or TCP port numbers. IP Filtering Use this to apply filtering based on IP addresses. MAC Filtering Use this to apply filtering based on MAC addresses. URL Filtering Use this to apply filtering based on URLs.
Chapter 3 Operation Modes 32 NBG2105 User’s Guide
C HAPT ER 4 Router Setup Wizard 4.1 Overview This chapter provides information on the wizard setup screens in the Web Configurator. The Web Configurator’s wizard setup helps you configure your device in router mode for the first time. 4.2 Welcome Screen Launch your web browser and type "http://192.168.1.1" as the website address. Type "admin" (default) as the user name and "1234" (default) as the password. Click Login. Click Wizard in router mode to open the Welcome screen.
Chapter 4 Router Setup Wizard 4.3.1 WAN Access Type: Static IP Select Static IP as the WAN Access Type to setup a static IP Configuration on the WAN port. Complete the fields described. Click Next to proceed with the Wireless Network Name (SSID) screen. Figure 13 WAN Access Type: Static IP The following table describes the labels in this screen. Table 9 WAN Access Type: Static IP LABEL DESCRIPTION WAN Access Type Select Static IP to enable manual configuration of all NBG2105 IP settings.
Chapter 4 Router Setup Wizard The following table describes the labels in this screen. Table 10 WAN Access Type: DHCP Client LABEL DESCRIPTION WAN Access Type Select DHCP Client to make the NBG2105 get its IP configuration from a DHCP server. Cancel Click this to cancel the wizard. Back Click this to go back to the previous step in the wizard. Next Click this to go to the next step in the wizard. 4.3.
Chapter 4 Router Setup Wizard The following table describes the labels in this screen. Table 11 WAN Access Type: PPPoE LABEL DESCRIPTION WAN Access Type Select PPPoE to make the NBG2105 get its IP configuration via PPPoE. User Name Enter the user name provided by your ISP. Password Enter the password provided by your ISP. Cancel Click this to cancel the wizard. Back Click this to go back to the previous step in the wizard. Next Click this to go to the next step in the wizard. 4.
Chapter 4 Router Setup Wizard 4.5.1 Encryption: None Choose None in the Encryption field to let wireless devices within range access your wireless network. Complete the fields described. Click Finished to save the configuration end exit the wizard. Figure 17 Encryption: None The following table describes the labels in this screen. Table 13 Encryption: None LABEL DESCRIPTION Encryption Select None to have no wireless LAN security configured.
Chapter 4 Router Setup Wizard The following table describes the labels in this screen. Table 14 Encryption: WEP LABEL DESCRIPTION Encryption Select WEP to allow clients to associate this network with WEP authentication. Key Length Select 64-bit or 128-bit. This dictates the length of the security key that the network is going to use. Key Format Select Hex to enter hexadecimal characters as a WEP key. Select ASCII to enter ASCII characters as WEP key.
Chapter 4 Router Setup Wizard The following table describes the labels in this screen. Table 15 Encryption: WPA-PSK, WPA2-PSK or WPA2-PSK Mixed LABEL DESCRIPTION Encryption Select WPA-PSK, WPA2-PSK or WPA2-PSK Mixed to allow clients to associate this network with WPA-PSK, WPA2-PSK or either WPA-PSK or WPA2-PSK authentication. Pre-Shared Key Format Select Passphrase to make the NBG2105 generate a key from a phrase typed into the Pre-Shared Key field.
Chapter 4 Router Setup Wizard 40 NBG2105 User’s Guide
C HAPT ER 5 AP Setup Wizard 5.1 Overview This chapter provides information on the wizard setup screens in the Web Configurator. The Web Configurator’s wizard setup helps you configure your device in AP mode for the first time. 5.2 Welcome Screen Launch your web browser and type "http://192.168.1.2" as the website address. Type "admin" (default) as the user name and "1234" (default) as the password. Click Login. Click Wizard in router mode to open the Welcome screen.
Chapter 5 AP Setup Wizard Figure 21 Wireless Network Name (SSID) The following table describes the labels in this screen. Table 16 Wireless Network Name (SSID) LABEL DESCRIPTION Wireless Network Name (SSID) Enter a descriptive name (up to 32 printable 7-bit ASCII characters) for the wireless LAN. If you change this field on the NBG2105, make sure all wireless stations use the same SSID in order to access the network. Cancel Click this to cancel the wizard.
Chapter 5 AP Setup Wizard The following table describes the labels in this screen. Table 17 Encryption: None LABEL DESCRIPTION Encryption Select None to have no wireless LAN security configured. If you do not enable any wireless security on your NBG2105, your network is accessible to any wireless networking device that is within range. Cancel Click this to cancel the wizard. Back Click this to go back to the previous step in the wizard. Finished Click this to finish the wizard. 5.4.
Chapter 5 AP Setup Wizard 5.4.3 Encryption: WPA-PSK, WPA2-PSK or WPA2-PSK Mixed Choose WPS-PSK, WPA2-PSK or WPA2-PSK Mixed in the Encryption field to protect your wireless network with WPA-PSK, WPA2-PSK or both at the same time. Complete the fields described. Click Finished to save the configuration end exit the wizard. Figure 24 Encryption: WPA2-PSK Mixed Note: Although only the WPA2-PSK Mixed screen is shown, all fields are the same for WPA-PSK, WPA2-PSK or WPA2-PSK Mixed screens.
C HAPT ER 6 Client Setup Wizard 6.1 Overview This chapter provides information on the wizard setup screens in the Web Configurator. The Web Configurator’s wizard setup helps you configure your device in Client mode for the first time. 6.2 Welcome Screen Launch your web browser and type "http://192.168.1.2" as the website address. Type "admin" (default) as the user name and "1234" (default) as the password. Click Login. Click Wizard in client mode to open the Welcome screen.
Chapter 6 Client Setup Wizard Figure 26 Wireless Network Name Setup The following table describes the labels in this screen. Table 20 Wireless Network Name Setup 46 LABEL DESCRIPTION Wireless Network Name (SSID) Enter the SSID of the AP to which you want the NBG2105 in client mode to connect. Channel Enter the channel number used by the wireless device to which the NBG2105 is connecting. This is optional if the AP does not broadcast and hides the SSID.
Chapter 6 Client Setup Wizard Table 20 Wireless Network Name Setup (continued) LABEL DESCRIPTION Back Click this to go back to the previous step in the wizard. Next Click this to open a screen to configure wireless security options. 6.4 Wireless Security Configure the wireless security settings on your NBG2105 in the following screen. The fields that show up depend on the kind of security you select. 6.4.
Chapter 6 Client Setup Wizard Figure 28 Encryption: WEP The following table describes the labels in this screen. Table 22 Encryption: WEP LABEL DESCRIPTION Encryption Select WEP to allow clients to associate this network with WEP authentication. Key Length Select 64-bit or 128-bit. This dictates the length of the security key that the network is going to use. Key Format Select Hex to enter hexadecimal characters as a WEP key. Select ASCII to enter ASCII characters as WEP key.
Chapter 6 Client Setup Wizard Figure 29 Encryption: WPA2-PSK Note: Although only the WPA2-PSK screen is shown, all fields are the same for the WPA-PSK screen. The following table describes the labels in this screen. Table 23 Encryption: WPA-PSK or WPA2-PSK LABEL DESCRIPTION Encryption Select WPA-PSK or WPA2-PSK to allow clients to associate this network with WPA or WPA2 authentication.
Chapter 6 Client Setup Wizard 50 NBG2105 User’s Guide
C HAPT ER 7 WISP+UR Setup Wizard 7.1 Overview This chapter provides information on the wizard setup screens in the Web Configurator. The Web Configurator’s wizard setup helps you configure the wireless network name and wireless network security in WISP+UR mode for the first time. 7.2 Welcome Screen Launch your web browser and type "http://192.168.1.2" as the website address. Type "admin" (default) as the user name and "1234" (default) as the password. Click Login.
Chapter 7 WISP+UR Setup Wizard Figure 31 WAN: Static IP The following table describes the labels in this screen. Table 24 WAN: Static IP LABEL DESCRIPTION WAN Access Type Select Static IP to enable manual configuration of all NBG2105 IP settings. Internet IP Address Enter the Internet-facing IP address. Subnet Mask Enter the subnet mask of the NBG2105 WAN interface. Default Gateway Enter the IP address of a default gateway to the Internet. DNS Enter the IP address of the DNS server.
Chapter 7 WISP+UR Setup Wizard Table 25 WAN: DHCP Client (continued) LABEL DESCRIPTION Back Click this to go back to the previous step in the wizard. Next Click this to open a screen to configure wireless security options. 7.3.3 PPPoE The NBG2105 supports PPPoE (Point-to-Point Protocol over Ethernet). PPPoE is an IETF standard (RFC 2516) specifying how a personal computer (PC) interacts with a broadband modem (DSL, cable, wireless, etc.) connection.
Chapter 7 WISP+UR Setup Wizard 7.4 Wireless Network Name Setup Name your wireless network by entering an SSID or by clicking Site Survey and selecting one of the detected devices. Click Next to proceed with the Wireless Security Mode screen. Figure 34 Wireless Network Name Setup The following table describes the labels in this screen.
Chapter 7 WISP+UR Setup Wizard Table 27 Wireless Network Name Setup (continued) LABEL DESCRIPTION Encrypt This displays the data encryption and authentication method used by this wireless device. Signal This displays the strength of the wireless signal. The signal strength mainly depends on the antenna output power and the distance between your NBG2105 and this device. Select Click this to select a device. Cancel Click this to cancel the wizard.
Chapter 7 WISP+UR Setup Wizard 7.5.2 Encryption: WEP Choose WEP in the Encryption field to protect your wireless network with Wired Equivalent Privacy. Complete the fields described. Click Finished to save the configuration end exit the wizard. Figure 36 Encryption: WEP The following table describes the labels in this screen. Table 29 Encryption: WEP LABEL DESCRIPTION Encryption Select WEP to allow clients to associate this network with WEP authentication. Key Length Select 64-bit or 128-bit.
Chapter 7 WISP+UR Setup Wizard Figure 37 Encryption: WPA2-PSK Note: Although only the WPA2-PSK screen is shown, all fields are the same for the WPA-PSK screen. The following table describes the labels in this screen. Table 30 Encryption: WPA-PSK or WPA2-PSK LABEL DESCRIPTION Encryption Select WPA-PSK or WPA2-PSK to allow clients to associate this network with WPA or WPA2 authentication.
Chapter 7 WISP+UR Setup Wizard 58 NBG2105 User’s Guide
C HAPT ER 8 Tutorials 8.1 Overview This chapter provides tutorials for setting up your NBG2105. • Set Up a Wireless Network with WPS • Configure Wireless Security without WPS 8.2 Set Up a Wireless Network with WPS This section gives you an example of how to set up wireless network using WPS. This example uses the NBG2105 as the AP and NWD210N as the wireless client which connects to a notebook. Note: The wireless client must be a WPS-aware device (for example, a WPS USB adapter or PCI card).
Chapter 8 Tutorials Note: Your NBG2105 has a WPS button located on its panel, as well as a WPS button in its configuration utility. Both buttons have exactly the same function; you can use one or the other. Note: It doesn’t matter which button is pressed first. You must press the second button within two minutes of pressing the first one. The NBG2105 sends the proper configuration settings to the wireless client. This may take up to two minutes.
Chapter 8 Tutorials 3 Click Start buttons (or button next to the PIN field) on both the wireless client utility screen and the NBG2105’s Wireless LAN > WPS screen within two minutes. The NBG2105 authenticates the wireless client and sends the proper configuration settings to the wireless client. This may take up to two minutes. Then the wireless client is able to communicate with the NBG2105 securely.
Chapter 8 Tutorials The instructions require that your hardware is connected (see the Quick Start Guide) and you are logged into the Web Configurator through your LAN connection (see Section 2.2 on page 19). 62 1 Make sure your NBG2105 is turned on and working as an AP or wireless router. 2 Open the Wireless LAN > Basic screen in the NBG2105’s Web Configurator. 3 Confirm that Disable Wireless LAN Interface is not selected. 4 Enter SSID_Example3 as the SSID and select 6 as the channel.
Chapter 8 Tutorials 7 Open the Status screen. Verify your wireless and wireless security settings under Wireless Network. 8.3.1 Configure Your Notebook Note: We use the ZyXEL NWD2205 wireless adapter utility screens as an example for the wireless client. The screens may vary for different models. 1 The NBG2105 supports IEEE 802.11b, IEEE 802.11g and IEEE 802.11n wireless clients. Make sure that your notebook or computer’s wireless adapter supports one of these standards.
Chapter 8 Tutorials 64 4 Select SSID_Example3 and click Connect. 5 Select AES and type the security key in the following screen. Click Next. 6 The Confirm Save window appears. Check your settings and click Save to continue.
Chapter 8 Tutorials 7 Check the status of your wireless connection in the screen below. If your wireless connection is weak or you have no connection, see the Troubleshooting section of this User’s Guide. If your connection is successful, open your Internet browser and enter http://www.zyxel.com or the URL of any other web site in the address bar. If you are able to access the web site, your wireless connection is successfully configured.
Chapter 8 Tutorials 66 NBG2105 User’s Guide
P ART II Technical Reference 67
C HAPT ER 9 LAN 9.1 Overview This chapter describes how to configure LAN settings. A Local Area Network (LAN) is a shared communication system to which many computers are attached. A LAN is a computer network limited to the immediate area, usually the same building or floor of a building. The LAN screens can help you configure a LAN DHCP server and manage IP addresses. Figure 40 LAN Example 9.2 What You Can Do • Use the LAN Interface Setup screen to change the IP address for your NBG2105 (Section 9.
Chapter 9 LAN 9.3.1 IP Pool Setup The NBG2105 is pre-configured with a pool of IP addresses starting from 192.168.1.100 to 192.168.1.200. This configuration leaves 98 IP addresses (excluding the NBG2105 itself) under 192.168.1.99 for other server computers, for instance, servers for mail, FTP, TFTP, web, etc., that you may have. 9.3.2 LAN TCP/IP The NBG2105 has built-in DHCP server capability that assigns IP addresses and DNS servers to systems that support DHCP client capability. 9.
Chapter 9 LAN Table 31 Network > LAN (continued) LABEL DESCRIPTION Show Clients Click this to show the IP addresses that have been issued by the DHCP server. This field is not configurable when DHCP server is disabled. Apply Changes Click this to save changes back to the NBG2105. Reset Click this to begin configuring this screen afresh. 9.4.1 Active DHCP Client Screen Use this screen to view which DHCP clients have accepted their IP configuration from the NBG2105.
Chapter 9 LAN 72 NBG2105 User’s Guide
C HAPTER 10 WAN 10.1 Overview This chapter discusses the NBG2105’s WAN screens. Use these screens to configure your NBG2105 for Internet access. A WAN (Wide Area Network) connection is an outside connection to another network or the Internet. It connects your private networks such as a LAN (Local Area Network) and other networks, so that a computer in one location can communicate with computers in other locations. 10.
Chapter 10 WAN WAN IP Address The WAN IP address is an IP address for the NBG2105, which makes it accessible from an outside network. It is used by the NBG2105 to communicate with other devices in other networks. It can be static (fixed) or dynamically assigned by the ISP each time the NBG2105 tries to access the Internet.
Chapter 10 WAN Figure 43 Network > WAN: Static IP The following table describes the labels in this screen. Table 33 Network > WAN: Static IP LABEL DESCRIPTION WAN Access Type Select Static IP to enable manual configuration of all NBG2105 IP settings. Internet IP Address Enter the Internet-facing IP address. Subnet Mask Enter the subnet mask of the NBG2105 WAN interface. Default Gateway Enter the IP address of a default gateway to the Internet.
Chapter 10 WAN Figure 44 Network > WAN: DHCP Client The following table describes the labels in this screen. Table 34 Network > WAN: DHCP Client LABEL DESCRIPTION WAN Access Type Select DHCP Client to make the NBG2105 get its IP configuration from a DHCP server. MTU Size Enter the MTU (Maximum Transmission Unit) size for each packet. If a larger packet arrives, the NBG2105 divides it into smaller fragments.
Chapter 10 WAN Operationally, PPPoE saves significant effort for both you and the ISP or carrier, as it requires no specific configuration of the broadband modem at the customer site. By implementing PPPoE directly on the NBG2105 (rather than individual computers), the computers on the LAN do not need PPPoE software installed, since the NBG2105 does that part of the task. Furthermore, with NAT, all of the LANs’ computers will have access.
Chapter 10 WAN 78 NBG2105 User’s Guide
C HAPTER 11 Quality of Service (QoS) 11.1 Overview Quality of Service (QoS) refers to both a network’s ability to deliver data with minimum delay, and the networking methods used to control the use of bandwidth. Without QoS, all traffic data is equally likely to be dropped when the network is congested. This can cause a reduction in network performance and make the network inadequate for time-critical application such as video-ondemand.
Chapter 11 Quality of Service (QoS) The following table describes the labels in this screen. Table 36 Network > QoS LABEL DESCRIPTION QoS Setup Enable QoS Select this to enable QoS. Upstream bandwidth (Kbps) This shows the amount of upstream bandwidth for the WAN interface that you can allocate using QoS. The NBG2105 automatically sets this number to the WAN interface’s actual upstream transmission speed.
C HAPTER 12 Dynamic DNS (DDNS) 12.1 Overview DDNS services let you use a domain name with a dynamic IP address. 12.2 What You Need To Know The following terms and concepts may help as you read through this chapter. What is DDNS? Dynamic Domain Name Service (DDNS) services let you use a fixed domain name with a dynamic IP address. Users can always use the same domain name instead of a different dynamic IP address that changes each time to connect to the NBG2105 or a server in your network.
Chapter 12 Dynamic DNS (DDNS) The following table describes the labels in this screen. Table 37 Network > Dynamic DNS 82 LABEL DESCRIPTION Enable DDNS Click this to enable dynamic DNS. Service Provider Select the name of your Dynamic DNS service provider. Domain Name Enter the domain name assigned by your service provider to your NBG2105. Username/Email Enter the user name assigned by your service provider to your NBG2105.
C HAPTER 13 Wireless LAN 13.1 Overview This chapter discusses how to configure the wireless network settings in your NBG2105. See the appendices for more detailed information about wireless networks. The following figure provides an example of a wireless network. Figure 48 Example of a Wireless Network The wireless network is the part in the blue circle. In this wireless network, devices A and B are called wireless clients.
Chapter 13 Wireless LAN • Use the Site Survey screen to scan for and connect to a wireless network automatically. (Section 13.6 on page 92) • Use the WPS screen to quickly set up a wireless network with strong security, without having to configure security settings manually (Section 13.8 on page 95). • Use the MAC Filtering screen to allow or deny wireless stations based on their MAC addresses from connecting to the NBG2105 (Section 13.9 on page 97). 13.1.
Chapter 13 Wireless LAN WEP Data Encryption WEP (Wired Equivalent Privacy) encryption scrambles all data packets transmitted between the NBG2105 and the AP or other wireless stations to keep network communications private. Both the wireless stations and the access points must use the same WEP key for data encryption and decryption. Authentication Type The IEEE 802.11b/g/n standard describes a simple authentication method between the wireless stations and AP.
Chapter 13 Wireless LAN MAC Address Filter Every wireless client has a unique identification number, called a MAC address.1 A MAC address is usually written using twelve hexadecimal characters2; for example, 00A0C5000002 or 00:A0:C5:00:00:02. To get the MAC address for each wireless client, see the appropriate User’s Guide or other documentation. You can use the MAC address filter to tell the AP which wireless clients are allowed or not allowed to use the wireless network.
Chapter 13 Wireless LAN The following table describes the labels in this screen. Table 38 Wireless LAN > Basic LABEL DESCRIPTION Disable Wireless LAN Interface Select this to disable the wireless LAN interface. Network Mode Select the frequency band and wireless network mode for your network. SSID Enter the SSID (Service Set IDentity) to identify the service set with which wireless clients are associated.
Chapter 13 Wireless LAN The following table describes the labels in this screen. Table 39 Wireless LAN > Basic: Show Active Clients LABEL DESCRIPTION MAC Address This shows the MAC addresses of wireless clients associated with the NBG2105. Mode This shows which wireless standard a wireless client is using to connect to the NBG2105. Tx Packet This shows how many packets have been transmitted by the NBG2105 since association.
Chapter 13 Wireless LAN Table 40 Wireless LAN > Advanced (continued) LABEL DESCRIPTION Beacon Interval Enter a value to configure how often beacon frames are broadcast. Preamble Type Select Short Preamble for better performance or Long Preamble for better compatibility. 20/40MHz Coexist Select Enabled to allow the NBG2105 to adjust the channel bandwidth automatically. RF Output Power Set the output power of the NBG2105 in this field.
Chapter 13 Wireless LAN The following table describes the labels in this screen. Table 41 Wireless LAN > Security: Disabled LABEL DESCRIPTION Encryption Select Disabled to allow any client to associate this network without authentication. Apply Changes Click this to save changes back to the NBG2105. Reset Click this to begin configuring this screen afresh. 13.5.
Chapter 13 Wireless LAN Table 42 Wireless LAN > Security: WEP (continued) LABEL DESCRIPTION Apply Changes Click this to save changes back to the NBG2105. Reset Click this to begin configuring this screen afresh. 13.5.3 WPA-PSK/WPA2-PSK/WPA2-PSK Mixed Select WPA-PSK, WPA2-PSK or WPA2-PSK Mixed from the Encryption list. Figure 54 Wireless LAN > Security: WPA2-PSK Mixed The following table describes the labels in this screen.
Chapter 13 Wireless LAN 13.6 Site Survey Screen Use this screen to scan for and connect to a wireless network automatically. Go to Wireless LAN > Site Survey to open the following screen. This screen is available only when the NBG2105 is in WISP+UR or Client mode. Figure 55 Wireless LAN > Site Survey The following table describes the labels in this screen.
Chapter 13 Wireless LAN Table 44 Wireless LAN > Site Survey (continued) LABEL DESCRIPTION Encrypt This displays the data encryption and authentication method used by this wireless device. Signal This displays the strength of the wireless signal. The signal strength mainly depends on the antenna output power and the distance between your NBG2105 and this device. Select Click this to select a device. Next Click this to open a screen to configure wireless security options. 13.
Chapter 13 Wireless LAN Figure 57 Wireless LAN > Site Survey: WEP The following table describes the labels in this screen. Table 46 Wireless LAN > Site Survey: WEP LABEL DESCRIPTION Encryption Select WEP to associate with the selected AP using WEP authentication. Key Type Select Open, Shared or Both. This field specifies whether the NBG2105 must provide a WEP key to login to the selected access point. Key Length Select 64-bit or 128-bit.
Chapter 13 Wireless LAN Figure 58 Wireless LAN > Site Survey: WPA2-PSK The following table describes the labels in this screen. Table 47 Wireless LAN > Site Survey: WPA-PSK or WPA2-PSK LABEL DESCRIPTION Encryption Select WPA-PSK or WPA2-PSK to associate with the selected AP using WPA-PSK or WPA2-PSK. Authentication Mode Personal (Pre-Shared Key) is selected to use a simple common password for authentication.
Chapter 13 Wireless LAN Figure 59 Wireless LAN > WPS (Router, AP, or WISP+UR mode) The following table describes the labels in this screen. Table 48 Wireless LAN > WPS (Router, AP, or WISP+UR mode) LABEL DESCRIPTION Disable WPS Select this to turn off the WPS feature. Apply Changes Click this to save changes back to the NBG2105. Reset Click this to begin configuring this screen afresh.
Chapter 13 Wireless LAN Figure 60 Wireless LAN > WPS (Client mode) The following table describes the labels in this screen. Table 49 Wireless LAN > WPS (Client mode) LABEL DESCRIPTION Disable WPS Select this to turn off the WPS feature. Apply Changes Click this to save changes back to the NBG2105. Reset Click this to begin configuring this screen afresh. Self PIN Number This is the WPS PIN (Personal Identification Number) of the NBG2105.
Chapter 13 Wireless LAN Figure 61 Wireless LAN > MAC Filtering The following table describes the labels in this screen. Table 50 Wireless LAN > MAC Filtering LABEL DESCRIPTION Wireless Access Control Mode Select Disable to turn off MAC address filtering, or define the filter action for the list of MAC addresses in the Current Access Control List. Select Allow Listed to permit access to the NBG2105, MAC addresses not listed will be denied access to the NBG2105.
C HAPTER 14 Firewall 14.1 Overview This chapter shows you how to enable and configure the NBG2105 firewall settings. The NBG2105 firewall is a packet filtering firewall and restricts access based on the source/ destination computer network address of a packet and the type of application. 14.2 What You Can Do • Use the Port Filtering screen to apply filtering based on UDP or TCP port numbers (Section 14.4 on page 100). • Use the IP Filtering screen to apply filtering based on IP addresses (Section 14.
Chapter 14 Firewall 5 For local services that are enabled, protect against misuse. Protect by configuring the services to communicate only with specific peers, and protect by configuring rules to block packets for the services at specific interfaces. 6 Keep the NBG2105 in a secured (locked) room. 14.4 Port Filtering Screen Click Firewall > Port Filtering to apply filtering based on UDP or TCP port numbers. Figure 62 Firewall > Port Filtering The following table describes the labels in this screen.
Chapter 14 Firewall 14.5 IP Filtering Screen Click Firewall > IP Filtering to apply filtering based on IP addresses. Figure 63 Firewall > IP Filtering The following table describes the labels in this screen. Table 52 Firewall > IP Filtering LABEL DESCRIPTION Enable IP Filtering Click this to apply filtering based on IP addresses. Local IP Address Enter the source IP address of outgoing packets or the destination IP address of incoming packets that this rule matches.
Chapter 14 Firewall Figure 64 Firewall > MAC Filtering The following table describes the labels in this screen. Table 53 Firewall > MAC Filtering LABEL DESCRIPTION Enable MAC Filtering Click this to apply filtering based on MAC addresses. MAC Address Enter the source MAC address of outgoing packets or the destination MAC address of incoming packets that this rule matches. Comment Enter a description of this rule. Apply Changes Click this to save changes back to the NBG2105.
Chapter 14 Firewall Figure 65 Firewall > URL Filtering The following table describes the labels in this screen. Table 54 Firewall > URL Filtering LABEL DESCRIPTION Enable URL Filtering Click this to apply filtering based on URLs. URL Address Enter the URL that this rule matches. Comment Enter a description of this rule. Apply Changes Click this to save changes back to the NBG2105. Reset Click this to begin configuring this screen afresh.
Chapter 14 Firewall 104 NBG2105 User’s Guide
C HAPTER 15 Management 15.1 Overview This chapter describes the Management screens. 15.2 What You Can Do • Use the NTP screen to change your NBG2105’s time and date (Section 15.3 on page 105). • Use the Password screen to change your NBG2105’s system password (Section 15.4 on page 106). • Use the Upgrade Firmware screen to upload firmware to your NBG2105 (Section 15.5 on page 107).
Chapter 15 Management Figure 66 Management > NTP The following table describes the labels in this screen. Table 55 Management > NTP LABEL DESCRIPTION Current Time Enter the current time, or click Copy Computer Time to use your computer to set the time. Copy Computer Time Click this to use your computer to set the time. Time Zone Select Choose the time zone of your location. This will set the time difference between your time zone and Greenwich Mean Time (GMT).
Chapter 15 Management Figure 67 Management > Password The following table describes the labels in this screen. Table 56 Management > Password LABEL DESCRIPTION User Name Enter your new user name. New Password Enter your new system password. Note that as you type a password, the screen displays an asterisk (*) for each character you type. Confirmed Password Enter the new password again in this field. Apply Changes Click this to save changes back to the NBG2105.
Chapter 15 Management The following table describes the labels in this screen. Table 57 Management > Upgrade Firmware LABEL DESCRIPTION Firmware Version This shows the current firmware version installed on the NBG2105. Browse... Click Browse... to find the .bin file you want to upload. Remember that you must decompress compressed (.zip) files before you can upload them. Upload Click Upload to begin the upload process. This process may take up to two minutes.
Chapter 15 Management Table 58 Management > Backup/Restore (continued) LABEL Upload DESCRIPTION Click this to begin the upload process. Note: Do not turn off the NBG2105 while configuration file upload is in progress. After you see a “configuration upload successful” screen, you must then wait one minute before logging into the NBG2105 again. The NBG2105 automatically restarts in this time causing a temporary network disconnect.
Chapter 15 Management Select the language you prefer and click Apply Changes. The Web Configurator language changes after a while without restarting the NBG2105. Figure 71 Management > Language 15.9 Restart Screen System restart allows you to reboot the NBG2105 without turning the power off. Click Maintenance > Reboot to open the following screen. Figure 72 Maintenance > Reboot Click Reboot to have the NBG2105 restart. This does not affect the NBG2105's configuration.
C HAPTER 16 Status 16.1 Overview This chapter describes how to show the general status of the NBG2105 as well as statistics and logs collected by the NBG2105. 16.2 What You Can Do • Use the Status screen to view system, wireless, local and WAN network information, as well as general information about the NBG2105. • Use the Statistics screen to show the number of packets sent and received on the Wireless LAN and Ethernet WAN interfaces.
Chapter 16 Status Figure 73 Status > Status (Router) The following table describes the labels in this screen. Table 60 Status > Status (Router) LABEL DESCRIPTION System Information Running Time This shows how long the NBG2105 has been running. Firmware Version This shows the currently running firmware version. Firmware Build Time This shows when the currently running firmware was compiled. Operation Mode This shows which mode the NBG2105 is in.
Chapter 16 Status Table 60 Status > Status (Router) (continued) LABEL DESCRIPTION Local MAC Address This shows the LAN Ethernet adapter MAC Address of your device. WAN Information Attain IP Protocol This shows how the WAN interface gets its IP configuration. WAN IP Address This shows the WAN interface’s IP address. Subnet Mask This shows the WAN interface’s subnet mask. Default Gateway This shows the WAN interface’s gateway IP address.
Chapter 16 Status Table 61 Status > Status (AP) (continued) LABEL DESCRIPTION Channel Selection This shows the channel number. Encryption This shows the type of wireless encryption the NBG2105 is using. BSSID This shows the wireless adapter MAC Address of your device. LAN Information Attain IP Protocol This shows how the LAN interface gets its IP configuration. Router IP Address This shows the LAN interface’s IP address. Subnet Mask This shows the LAN interface’s subnet mask.
Chapter 16 Status Table 62 Status > Status (Client) (continued) LABEL DESCRIPTION Operation Mode This shows which mode the NBG2105 is in. WLAN Information Channel Bandwidth This shows which frequency band and wireless mode your network uses. SSID This shows the wireless network name of the AP to which the NBG2105 is connecting. Channel Selection This shows the channel number. Encryption This shows the type of wireless encryption the NBG2105 is using.
Chapter 16 Status Figure 76 Status > Status (WISP+UR) The following table describes the labels in this screen. Table 63 Status > Status (WISP+UR) LABEL DESCRIPTION System Information Running Time This shows how long the NBG2105 has been running. Firmware Version This shows the currently running firmware version. Firmware Build Time This shows when the currently running firmware was compiled. Operation Mode This shows which mode the NBG2105 is in.
Chapter 16 Status Table 63 Status > Status (WISP+UR) (continued) LABEL DESCRIPTION BSSID This shows the wireless adapter MAC Address of your device. State This shows what stage the NBG2105 is at with respect to connecting to access points. LAN Information Attain IP Protocol This shows how the LAN interface gets its IP configuration. Router IP Address This shows the LAN interface’s IP address. Subnet Mask This shows the LAN interface’s subnet mask.
Chapter 16 Status Figure 79 Status > Statistics (WISP+UR) Table 64 Status > Statistics LABEL DESCRIPTION Wireless LAN Sent Packets This shows the number of packets sent through the wireless LAN interface. Received Packets This shows the number of packets received on the wireless LAN interface. Ethernet WAN Sent Packets This shows the number of packets sent through the Ethernet WAN interface. Received Packets This shows the number of packets received on the Ethernet WAN interface.
Chapter 16 Status Figure 80 Status > Log The following table describes the labels in this screen. Table 65 Status > Log LABEL DESCRIPTION Enable Log Select this to enable logging. system all Select this to log all events, including wireless events. wireless Select this to log only wireless events. Apply Changes Click this to save changes back to the NBG2105. Refresh Click this to update the screen. Clear Click this to delete the log.
Chapter 16 Status 120 NBG2105 User’s Guide
C HAPTER 17 Troubleshooting 17.1 Overview This chapter offers some suggestions to solve problems you might encounter. The potential problems are divided into the following categories. • Power, Hardware Connections, and LEDs • NBG2105 Access and Login • Internet Access • Resetting the NBG2105 to Its Factory Defaults • Wireless LAN Connections 17.2 Power, Hardware Connections, and LEDs The NBG2105 does not turn on. None of the LEDs turn on.
Chapter 17 Troubleshooting 17.3 NBG2105 Access and Login I don’t know the IP address of my NBG2105. 1 The default IP address of the NBG2105 in Router mode is 192.168.1.1. The default IP address of the NBG2105 in other modes is 192.168.1.2. 2 If you changed the IP address and have forgotten it, you might get the IP address of the NBG2105 (in Router or WISP+UR mode) by looking up the IP address of the default gateway for your computer.
Chapter 17 Troubleshooting • If there is a DHCP server on your network, make sure your computer is using a dynamic IP address. See Section 9.4 on page 70. • If there is no DHCP server on your network, make sure your computer’s IP address is in the same subnet as the NBG2105. See Section 9.4 on page 70. 5 Reset the device to its factory defaults, and try to access the NBG2105 with the default IP address. See Section 1.5 on page 14.
Chapter 17 Troubleshooting 3 If the NBG2105 is in Router or WISP+UR mode make sure you entered your ISP account information correctly in the wizard or the WAN screen. These fields are case-sensitive, so make sure [Caps Lock] is not on. 4 If you are trying to access the Internet wirelessly, make sure the wireless settings in the wireless client are the same as the settings in the AP. 5 Disconnect all the cables from your device, and follow the directions in the Quick Start Guide again.
Chapter 17 Troubleshooting You will lose all of your changes when you push the RESET button. To reset the NBG2105: 1 Make sure the power LED is on. 2 Press the RESET button for longer than five seconds to set the NBG2105 back to its factory-default configurations. If the NBG2105 restarts automatically, wait for the NBG2105 to finish restarting, and log in to the Web Configurator. The password is “1234”. If the NBG2105 does not restart automatically, disconnect and reconnect the NBG2105’s power.
Chapter 17 Troubleshooting What factors may cause intermittent or unstabled wireless connection? How can I solve this problem? The following factors may cause interference: • Obstacles: walls, ceilings, furniture, and so on. • Building Materials: metal doors, aluminum studs. • Electrical devices: microwaves, monitors, electric motors, cordless phones, and other wireless devices.
A PPENDIX A Pop-up Windows, JavaScript and Java Permissions In order to use the web configurator you need to allow: • Web browser pop-up windows from your device. • JavaScript (enabled by default). • Java permissions (enabled by default). Note: The screens used below belong to Internet Explorer version 6, 7 and 8. Screens for other Internet Explorer versions may vary. Internet Explorer Pop-up Blockers You may have to disable pop-up blocking to log into your device.
Appendix A Pop-up Windows, JavaScript and Java Permissions Figure 82 Internet Options: Privacy 3 Click Apply to save this setting. Enable Pop-up Blockers with Exceptions Alternatively, if you only want to allow pop-up windows from your device, see the following steps. 128 1 In Internet Explorer, select Tools, Internet Options and then the Privacy tab. 2 Select Settings…to open the Pop-up Blocker Settings screen.
Appendix A Pop-up Windows, JavaScript and Java Permissions Figure 83 Internet Options: Privacy 3 Type the IP address of your device (the web page that you do not want to have blocked) with the prefix “http://”. For example, http://192.168.167.1. 4 Click Add to move the IP address to the list of Allowed sites.
Appendix A Pop-up Windows, JavaScript and Java Permissions 5 Click Close to return to the Privacy screen. 6 Click Apply to save this setting. JavaScript If pages of the web configurator do not display properly in Internet Explorer, check that JavaScript are allowed. 1 In Internet Explorer, click Tools, Internet Options and then the Security tab. Figure 85 Internet Options: Security 130 2 Click the Custom Level... button. 3 Scroll down to Scripting.
Appendix A Pop-up Windows, JavaScript and Java Permissions Figure 86 Security Settings - Java Scripting Java Permissions 1 From Internet Explorer, click Tools, Internet Options and then the Security tab. 2 Click the Custom Level... button. 3 Scroll down to Microsoft VM. 4 Under Java permissions make sure that a safety level is selected. 5 Click OK to close the window.
Appendix A Pop-up Windows, JavaScript and Java Permissions Figure 87 Security Settings - Java JAVA (Sun) 1 From Internet Explorer, click Tools, Internet Options and then the Advanced tab. 2 Make sure that Use Java 2 for
Appendix A Pop-up Windows, JavaScript and Java Permissions Mozilla Firefox Mozilla Firefox 2.0 screens are used here. Screens for other versions may vary slightly. The steps below apply to Mozilla Firefox 3.0 as well. You can enable Java, Javascript and pop-ups in one screen. Click Tools, then click Options in the screen that appears. Figure 89 Mozilla Firefox: TOOLS > Options Click Content to show the screen below. Select the check boxes as shown in the following screen.
Appendix A Pop-up Windows, JavaScript and Java Permissions Opera Opera 10 screens are used here. Screens for other versions may vary slightly. Allowing Pop-Ups From Opera, click Tools, then Preferences. In the General tab, go to Choose how you prefer to handle pop-ups and select Open all pop-ups. Figure 91 Opera: Allowing Pop-Ups Enabling Java From Opera, click Tools, then Preferences. In the Advanced tab, select Content from the leftside menu. Select the check boxes as shown in the following screen.
Appendix A Pop-up Windows, JavaScript and Java Permissions Figure 92 Opera: Enabling Java To customize JavaScript behavior in the Opera browser, click JavaScript Options. Figure 93 Opera: JavaScript Options Select the items you want Opera’s JavaScript to apply.
Appendix A Pop-up Windows, JavaScript and Java Permissions 136 NBG2105 User’s Guide
A PPENDIX B Legal Information Copyright Copyright © 2012 by ZyXEL Communications Corporation. The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the prior written permission of ZyXEL Communications Corporation. Published by ZyXEL Communications Corporation.
Appendix B Legal Information 率 輻 理 率 不 更 率 率 率 更 不 立 率 療 輻 Notices Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device is designed for the WLAN 2.4 GHz and/or 5 GHz networks throughout the EC region and Switzerland, with restrictions in France. Ce produit est conçu pour les bandes de fréquences 2,4 GHz et/ou 5 GHz conformément à la législation Européenne.
Appendix B Legal Information [Spanish] Por medio de la presente ZyXEL declara que el equipo cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. [Greek] ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ ZyXEL ΔΗΛΩΝΕΙ ΟΤΙ εξοπλισμός ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕC.
Appendix B Legal Information 2400-2483.5 100 5150-5350 200 5470-5725 1000 V V V Belgium The Belgian Institute for Postal Services and Telecommunications (BIPT) must be notified of any outdoor wireless link having a range exceeding 300 meters. Please check http://www.bipt.be for more details. Draadloze verbindingen voor buitengebruik en met een reikwijdte van meer dan 300 meter dienen aangemeld te worden bij het Belgisch Instituut voor postdiensten en telecommunicatie (BIPT). Zie http://www.bipt.
Appendix B Legal Information List of national codes COUNTRY ISO 3166 2 LETTER CODE COUNTRY ISO 3166 2 LETTER CODE Austria AT Malta MT Belgium BE Netherlands NL Cyprus CY Poland PL PT Czech Republic CR Portugal Denmark DK Slovakia SK Estonia EE Slovenia SI Finland FI Spain ES France FR Sweden SE Germany DE United Kingdom GB Greece GR Iceland IS Hungary HU Liechtenstein LI Ireland IE Norway NO Italy IT Switzerland CH Latvia LV Bulgaria BG Lithuania
Appendix B Legal Information 142 NBG2105 User’s Guide
Index Index A D Address Assignment 74 Advanced Encryption Standard 85 DDNS 81 see also Dynamic DNS AP 13 disclaimer 137 AP mode 24 menus 26 navigation 25 setting 25 wizard 41 DNS Server 74 AP+Bridge 13 Dynamic DNS 81 authentication type 85 auto 85 open system 85 shared key 85 E documentation related 2 Domain Name System. See DNS.
Index L Q LAN 69 QoS 79 LAN overview 69 Quality of Service 79 Local Area Network 69 Quick Start Guide 2 M R MAC address 86 cloning 74 registration product 138 MAC address filter 86 related documentation 2 managing the device good habits 13 using the web configurator. See web configurator. using the WPS. See WPS.
Index W WAN (Wide Area Network) 73 warranty 138 note 138 Web Configurator how to access 19 Overview 19 web configurator 13 WEP (Wired Equivalent Privacy) 85 Wi-Fi Protected Access 85 wireless ISP 29 Wireless network basic guidelines 83 channel 84 example 83 MAC address filter 86 overview 83 security 84 SSID 84 Wireless security 84 overview 84 type 84 Wireless tutorial 59 WISP 29 WISP+UR mode 29 example 29 menus 30 navigation 29 setting 29 wizard 51 WLAN button 14 WPA 85 vs WPA-PSK 85 WPA2 85 vs WPA2-PSK 85
Index 146 NBG2105 User’s Guide
