V500 Series IP Phone Models: V500-T1 V501-T1 Quick Start Guide Version 1.00 01/2009 Edition 3 CONTENTS ENGLISH 3 DEUTSCH 17 ESPAÑOL 35 FRANÇAIS 51 ITALIANO 69 NEDERLANDS 87 РУССКИЙ 103 简体中文 123 繁體中文 139 Copyright © 2008. All rights reserved.
ENGLISH Overview At the time of writing, this Quick Start Guide covers the following models: • V500-T1: IP Phone. • V501-T1: IP Phone with Power over Ethernet (PoE). This Quick Start Guide shows you how to set up and use your V500. It includes the following sections: • Hardware and Connections - introduces the physical features of the V500 and shows you how to connect it to your network.
ENGLISH 1 Hardware and Connections 1 Handset 2 LCD screen 3 Account keys 4 Softkeys 5 Line keys 6 Menu 7 Navigator 8 Phonebook 9 Action keys 10 Alphanumeric keypad 11 Microphone 12 Volume keys 13 Function keys 14 Custom keys The following table describes some of the hardware features used for basic operations. See the hardware chapter in your User’s Guide for full descriptions of all features. FEATURE DESCRIPTION Account keys Use these to select the SIP account you want to use.
ENGLISH FEATURE DESCRIPTION Softkeys These keys’ functions depend on the screen currently displayed on the LCD screen. A word or symbol displayed on the LCD screen above a softkey shows its current function. Line keys Press these to select the phone line you want to use. The V500 has four phone lines. Menu Press this to display the V500’s configuration menu. Press it again to exit the menu. The menu is not accessible when a call is in progress.
ENGLISH If you want to stand the V500 at its lower angle (nearer the horizontal) use the holes marked 1 in the following figure. Use the holes marked 2 to stand the V500 at its higher angle (nearer the vertical). Take the stand and connect it to the V500 as shown in the following figure. 1 Insert the two connectors on the longer side of the stand first. 2 Pivot the stand down until the other two connectors are inserted. 3 Turn the V500 the right way up. Check that the stand is securely attached.
ENGLISH 1.2 Rear Panel Hardware Connections 1 WAN: Use an Ethernet cable to connect the V500 to your network. V501-T1 only: If you are using Power over Ethernet (PoE), connect the Ethernet cable supplying power to this port. See Section 1.3 on page 8 for more information on PoE.
ENGLISH 1.3 V501-T1 Only: Power over Ethernet (Optional) Power over Ethernet (PoE) is the ability to provide power to your V501-T1 via an 8-pin CAT 5 Ethernet cable, eliminating the need for a nearby power source. A PoE injector (not included) is also needed to supply the Ethernet cable with power. This feature allows increased flexibility in the location of your V501. In the following figure, Z is your V501, A is the CAT 5 Ethernet cable, B is the PoE injector and C is the power cable.
ENGLISH 2.1 Set up Your Network Connection When you have finished your hardware connections, look at the LCD screen. The V500 displays your Voice over Internet (VoIP) account registration status in the tabs on the right, and time and date details in the top section. The V500 allows you to configure up to four VoIP accounts (also known as SIP accounts). When a VoIP account is not active, Unused displays. When an account is active but not successfully registered, No Reg displays in the tab.
ENGLISH 2 Select Network Setting. Advanced Setting Choose from the following options: 1 Network Setting • If you were given a username and password for network access, go to section 2.1.1 on page 10. 2 SIP Configuration • If you were given an IP address and subnet mask to use, go to section 2.1.2 on page 12. 4 Programmable Key • If you were not given an IP address to use, go to section 2.1.3 on page 12.
ENGLISH 3 The PPPoE Username screen displays. Press Edit and enter your user name. (Press the # key to cycle between Number, Uppercase, Lowercase and Symbol entry mode.) PPPoE Username Number Current: New: User123 Press Save when you are done, then press 2 to enter the PPPoE Password screen. Press Edit. 4 Enter your password, then go down to Confirm and re-enter it. Press Save when you are done. Save .
ENGLISH 2.1.2 Set Up a Static IP Address 1 If you have an IP address to use, select Static IP (Off) in the Advanced Setting > Network Setting menu. Press the On softkey to have the V500 use a static IP address. The screen displays Static IP (On). Press Select to enter your information.
ENGLISH 2.2 Set up Your Voice Account Follow these steps to configure your VoIP account. 1 Press the Menu key, then press 6 to enter the Advanced Setting menu. 2 Press 2 to enter the SIP Configuration menu. 3 If VoIP 1 Config. does not display Active, select its entry and press the Active softkey. If the SIP account is not active, you cannot use it to make or receive calls. SIP Configuration 1 VoIP 1 Config. (On) 2 VoIP 2 Config. (Off) 3 VoIP 3 Config. (Off) 4 VoIP 4 Config.
ENGLISH FIELD DESCRIPTION 7 SIP Register Port This is the port the SIP register server uses to register the V500. The default is 5060. 8 SIP Service Domain If you have a SIP account like 1234567@voip-provider.com, the SIP Service Domain is voip-provider.com. 9 SIP Auth ID This is the user name for this SIP account. 10 Auth Password This is the password for this SIP account. 11 Codec Priority Your V500 and the SIP server must use the same voice codec (coder / decoder).
ENGLISH 3 Phone Operation This section describes how to use your V500’s basic telephone functions. " For more information on the V500’s telephone functions, see the hardware chapter in your User’s Guide. MAKING A CALL 1 Pick up the handset. A Line key LED turns on. The LCD screen shows which SIP account you are using. Change these, if you want, using the Line and Account keys. 2 Check that you can hear a dial tone. 3 Enter the number you want to call.
ENGLISH USING VOICEMAIL Once you have configured your SIP account’s voicemail number on the V500, press the VOICEMAIL key to check your messages. Use the Advanced Setting > SIP Configuration > SIP 1 ~ 4 Configuration > Voicemail Number menu to set the voicemail account number. The account you check when you press the VOICEMAIL key depends on which SIP account is currently active. See your User’s Guide for more information.
DEUTSCH Übersicht Zum Zeitpunkt der Druckstellung umfasst die Kurzanleitung die folgenden Modelle: • V500: IP-Phone. • V501: IP-Phone mit PoE (Power over Ethernet). In dieser Kurzanleitung wird beschrieben, wie Sie das I-Phone V500 einrichten und bedienen. Es umfasst die folgenden Abschnitte: • Hardware und Anschlüsse - hier werden die physikalischen Merkmale des V500 erläutert, und es wird beschrieben, wie das Gerät an das Netzwerk angeschlossen wird.
DEUTSCH 1 Hardware und Anschlüsse 1 Telefonhörer 2 LCD-Display 3 SIP Kontotasten 4 SoftkeyTasten 5 Leitungstasten 6 Menu 7 Navigationsta sten 8 Telefonbuch 9 Aktionstasten 10 Alphanumeris che Tastatur 11 Mikrofon 12 Lautstärketast en 13 Funktionstaste n 14 Benutzerdefini erte Tasten 18
DEUTSCH In der folgenden Tabelle sind einige der für die Grundfunktionen erforderlichen Tasten und Anschlüsse beschrieben. Eine umfassende Beschreibung aller Tasten finden Sie im Kapitel Hardware des Benutzerhandbuchs. FUNKTION BESCHREIBUNG Account keys (SIP Kontotasten) Mit diesen Tasten können Sie das gewünschte SIP-Konto wählen. Auf dem V500 können Sie bis zu vier SIP-Konten konfigurieren.
DEUTSCH FUNKTION BESCHREIBUNG Volume keys Mit der Taste + können Sie die Lautstärke erhöhen, mit der Taste - können (Lautstärketast Sie sie verringern. en) • Wenn Sie den Hörer angeschlossen haben, wird mit diesen Tasten die Sprech- und Hörlautstärke des Hörers eingestellt. • Wenn Sie ein Headset verwenden, wird mit diesen Tasten die Sprechund Hörlautstärke des Kopfhörer- ( ) und des Mikrofonanschlusses ( ) des V500 eingestellt.
DEUTSCH Verbinden Sie den Ständer wie in der folgenden Abbildung dargestellt mit dem V500. 1 Schließen Sie erst die zwei Stecker an der längeren Seite des Ständers an. 2 Drehen Sie den Ständern nach unten, bis die zwei Stecker eingesteckt sind. 3 Drehen Sie das V500 ganz nach oben. Stellen Sie sicher, dass der Ständer gut befestigt ist. 1.
DEUTSCH 1 WAN: Das V500 wird mit einem Ethernet-Kabel an das Netzwerk angeschlossen. Nur V501: Wenn Sie PoE (Power over Ethernet) verwenden, schließen Sie hier ein Ethernet-Kabel an, das diesen Port mit Strom versorgt. Weitere Informationen zu PoE finden Sie unter Abschnitt 1.3 auf Seite 22.
DEUTSCH 2 Erstkonfiguration In diesem Abschnitt wird beschrieben, wie die Menüs auf dem LCD-Bildschirm des IPPhones verwendet werden: • Einrichten der Netzwerkverbindung und • Einrichten des Voice-Kontos Das IP-Phone muss dazu nicht an einen Computer angeschlossen sein. " Bei der Eingabe Ihrer Daten können Sie mit der Taste # zwischen dem Großbuchstabenmodus, dem Kleinbuchstabenmodus, dem Zeichenmodus und dem Zahlenmodus wechseln. Der jeweils aktive Modus wird auf dem LCD-Bildschirm angezeigt.
DEUTSCH V Wenn auf dem LCD-Bildschirm nichts angezeigt wird, prüfen Sie die Hardwareanschlüsse. Siehe Abschnitt 1.2. Führen Sie die folgenden Schritte aus, um Ihre Netzwerkeinstellungen zu konfigurieren. 1 Drücken Sie auf die Taste Menu, und wählen Sie mit den Navigationstasten die Option Advanced Setting (Erweiterte Einstellungen). Drücken Sie auf Select (Wählen).
DEUTSCH 2.1.1 Einrichten von PPPoE 1 Wenn Sie einen Benutzernamen und ein Kennwort erhalten haben, wählen Sie im Menü Advanced Setting (Erweiterte Einstellungen) > Network Setting (Netzwerkeinstellungen) die Option PPPoE (Off) (PPPoE (Aus)). Drücken Sie auf die Softkey-Taste On (Ein), damit das V500 PPPoE verwendet. Netzwerkeinstellung 1 PPPoE (Ein) 2 Statische IP (Aus) 3 DHCP (Aus) Auf dem Bildschirm wird PPPoE (On) (PPPoE (Ein)) angezeigt. Drücken Sie auf Select (Wählen), um Ihre Daten einzugeben.
DEUTSCH 4 Geben Sie Ihr Kennwort ein, wechseln Sie zu Confirm (Bestätigen), und geben Sie es dort erneut ein. Wenn Sie fertig sind, drücken Sie auf Save (Speichern). Kennwort bearbeiten Aktuell: Neu: Neues Kennwort Bestätigen: Neues Kennwort Kleinbuchstabenmodus Speichern <- Zurück 2.1.
DEUTSCH 2 Verwenden Sie die Optionen in diesem Menü, um die statische IP-Adresse, das Gateway und die DNS-Daten einzugeben, die Sie von Ihrem Internetdienstanbieter (ISP) oder Netzwerkverwalter erhalten haben. Drücken Sie auf Back (Zurück), um zum vorhergehenden Fenster zurückzukehren. Statische IP 1 IP-Adresse 2 Standard-Gateway 3 Subnetzmaske 4 1. DNS /DNS 5 2. DNS /DNS Wählen Zurück 2.1.
DEUTSCH 2.2 Einrichten des Voice-Kontos Führen Sie diese Schritte aus, um Ihr VoIP-Konto zu konfigurieren. 1 Drücken Sie auf die Taste Menu, und wählen Sie mit 6 die Option Advanced Setting (Erweiterte Einstellungen). 2 Rufen Sie mit 2, um das Menü SIP Configuration (SIP-Konfiguration) aufzurufen. 3 Wenn die Option VoIP 1 Config. (VoIP 1Konfig.) nicht als Active (Aktiv) angezeigt wird, wählen Sie diesen Eintrag, und drücken Sie auf die Softkey-Taste Active (Aktiv).
DEUTSCH FELD BESCHREIBUNG 3 SIP Local Port (Lokaler SIP-Port) Dieses ist der Port des V500, der für SIP-Anrufe verwendet wird. Die Standardeinstellung ist 5060. 4 SIP Server Addr (SIP-ServerAdresse) Dieses ist die IP-Adresse des Servers, den Ihr VoIP-Dienstanbieter für SIP-Anrufe verwendet. 5 SIP Server Port (SIP-Server-Port) Dieses ist der Port auf dem SIP-Server, der für SIP-Anrufe verwendet wird. Die Standardeinstellung ist 5060.
DEUTSCH FELD BESCHREIBUNG 15 NAT Setting (NAT-Einstellung) Hier können Sie NAT konfigurieren. 16 Backup SIP Hier können Sie die SIP-Server festlegen, die das V500 verwenden soll, Server (SIPwenn es nicht auf den SIP-Hauptserver zugreifen kann. Sicherungsserver) 5 Wenn Sie die Konfiguration bei SIP 1 Configuration (SIP 1-Konfiguration) beendet haben, drücken Sie auf Back (Zurück). Im rechten oberen Bereich des LCD-Bildschirms erscheint der registrierte SIP-Kontoname (in diesem Beispiel “SIP1”).
DEUTSCH 3 Die wichtigsten Telefonfunktionen In diesem Abschnitt wird beschrieben, wie Sie die Telefon-Grundfunktionen des V500 verwenden. " Weitere Informationen zu den Telefonfunktionen des V500 finden Sie im Kapitel zur Hardware in Ihrem Benutzerhandbuch. TÄTIGEN EINES ANRUFS 1 Nehmen Sie den Hörer auf. Eine Leitungstasten-LED beginnt zu leuchten. Auf dem LCD-Bildschirm wird angezeigt, welches Konto Sie verwenden. Sie können Leitung und Konto mit den Leitungs- und Kontotasten ändern.
DEUTSCH BEENDEN EINES ANRUFS Wenn Sie einen Anruf beenden möchten, drücken Sie auf die Taste HANG UP (Auflegen). Sie können auch einen der folgenden Schritte ausführen: • Wenn Sie den Hörer verwenden, setzen Sie ihn in die Ladestation. • Wenn Sie die interne Freisprechfunktion verwenden, drücken Sie auf die Taste SPEAKER Lautsprecher. • Wenn Sie ein externes Headset verwenden, drücken Sie auf die Taste HEADSET.
DEUTSCH WEITERLEITEN EINES ANRUFS Führen Sie die folgenden Schritte aus, um ein laufendes Gespräch auf eine andere Telefonnummer weiterzuleiten. 1 Drücken Sie während eines laufenden Telefongesprächs auf die Transfer-Taste. Die nächste freie Leitung wird automatisch aktiviert. Stellen Sie sicher, dass ein Freizeichen zu hören ist. 2 Wählen Sie die Nummer, an die ein Anruf weitergeleitet werden soll.
DEUTSCH 34
ESPAÑOL Vista general En el momento de escribir esta Guía de instalación rápida se cubren los siguientes modelos: • V500: Teléfono IP. • V501: Teléfono IP con Power over Ethernet (PoE). Esta Guía de inicio rápido le muestra cómo configurar y usar su V500. Incluye las siguientes secciones: • Hardware y conexiones - introduce las características físicas del V500 y le muestra cómo conectarlo a su red.
ESPAÑOL 1 Hardware y conexiones 1 Auricular 2 Pantalla LCD 3 Teclas de cuentas 4 Teclas suaves 5 Teclas de línea 6 Menú 7 Navegador 8 Agenda 9 Teclas de acción 10 Teclado alfanumérico 11 Micrófono 12 Teclas de volumen 13 Teclas de función 14 Teclas personales 36
ESPAÑOL La tabla siguiente describe algunas de las características usadas para las operaciones básicas. Consulte el capítulo del hardware en su Guía del usuario para una descripción completa de todas las características. CARACTERÍSTICA DESCRIPCIÓN Account keys (Teclas de cuentas) Utilícelas para seleccionar la cuenta SIP que desea usar. Puede configurar hasta cuatro cuentas SIP en el V500.
ESPAÑOL CARACTERÍSTICA DESCRIPCIÓN Volume keys (Teclas Utilice la tecla + para subir el volumen y utilice la tecla - para bajarlo. de volumen) • Cuando utilice el auricular, las teclas controlarán el volumen del habla y escucha del auricular. • Cuando utilice el auricular, estas teclas controlarán el volumen de habla y escucha en los puertos de auriculares ( ) y micrófono ( ) del V500. • Cuando utilice el altavoz, estas teclas controlarán el volumen del altavoz interno y del Mic (micrófono). 1.
ESPAÑOL Conecte el soporte al V500 como se muestra en la figura siguiente. 1 Inserte primero los dos conectores del lado más largo del soporte. 2 Gire el soporte hasta que los otros dos conectores queden insertados. 3 Gire el V500 hacia arriba. Compruebe que el soporte quede bien fijo. 1.
ESPAÑOL 1 WAN: Utilice un cable Ethernet para conectar el V500 a su red. Sólo V301: Si utiliza Power over Ethernet (PoE), conecte el cable de suministro eléctrico Ethernet en este puerto. Consulte Sección 1.3 en la página 40 para más información sobre PoE.
ESPAÑOL 2 Configuración inicial Esta sección describe cómo usar los menús de la pantalla LCD del teléfono para: • Configurar su conexión de red y • Configurar su cuenta de voz El teléfono no necesita estar conectado a un ordenador para hacer esto. " Cuando introduzca información, utilice la tecla # para cambiar entre los modos Uppercase (Mayúsculas), Lowercase (Minúsculas), Symbol (Símbolos) y Number (Números). El modo actual aparece en la pantalla LCD.
ESPAÑOL 1 Presione la tecla Menu y utilice el navegador para seleccionar Advanced Setting (Configuración avanzada). Presione Select (Seleccionar). Configuración del menú 1 Información del sistema 2 Configuración del anillo 3 Configuración del volumen 4 Preferencias de llamada 5 Agenda 6 Configuración avanzada 7 Reiniciar sistema 8 Configuración del logotipo Seleccio nar " Atrás También puede usar el teclado alfanumérico para realizar sus selecciones en la pantalla LCD.
ESPAÑOL 2.1.1 Configurar PPPoE 1 Si se le ha facilitado un nombre de usuario y una contraseña, seleccione PPPoE (Off) en el menú Advanced Setting (Configuración avanzada) > Network Setting (Configuración de red). Presione la tecla suave On (Activado) para que el V500 utilice PPPoE. Configuración de red 1 PPPoE (Activado) 2 IP estática (Desactivado) 3 DHCP (Desactivado) La pantalla mostrará PPPoE (On). Presione Select (Seleccionar) para introducir la información.
ESPAÑOL 4 Escriba su contraseña, baje hasta Confirm (Confirmar) y vuelva a escribirla. Presione Save (Guardar) de nuevo cuando haya finalizado. Editar contraseña Actual: Nueva: Nueva contraseña Confirmar: Nueva contraseña Modo Minúsculas Guardar <- Atrás 2.1.2 Configurar una dirección IP estática 1 Si tiene una dirección IP, seleccione Static IP (Off) en el menú Advanced Setting (Configuración avanzada) > Network Setting (Configuración de red).
ESPAÑOL 2.1.3 Obtener una dirección IP automáticamente " El V500 ha sido configurado por defecto para obtener una dirección IP automáticamente. 1 Si no tiene un nombre de usuario y contraseña ni una dirección IP, seleccione DHCP (Off) en el menú Advanced Setting (Configuración avanzada) > Network Setting (Configuración de red). Presione la tecla suave On (Activado) para que el V500 utilice DHCP.
ESPAÑOL " Si su proveedor de servicios VoIP no le ha facilitado la información para usar cualquiera de los campos del menú, déjelos con sus valores predeterminados. La siguiente tabla describe los campos de este menú. CAMPO DESCRIPCIÓN 1 Display Name (Mostrar nombre) Elija un nombre para esta cuenta SIP. Este nombre aparece en la ficha de la cuenta SIP de la pantalla LCD del V500. 2 SIP Number (Número SIP) Éste es su número de cuenta SIP. Si tiene una cuenta SIP como 1234567@voip-provider.
ESPAÑOL CAMPO DESCRIPCIÓN 12 Voicemail Number (Número correo de voz) Éste es el número que escribe para acceder a sus mensajes de correo de voz para esta cuenta SIP. 13 DNS SRV / DNS Actívelo (seleccione On) para que el V500 utilice los servidores DNS configurados en la sección 2.1.2. Desactívelo (seleccione Off) si no desea que el V500 utilice DNS. DNS SRV está desactivado por defecto.
ESPAÑOL 3 Uso del teléfono Esta sección describe cómo usar las funciones telefónicas básicas de su V500. " Para más información sobre las funciones telefónicas del V500, consulte el capítulo del hardware en su Guía del usuario. REALIZAR UNA LLAMADA 1 Descuelgue el auricular. Se enciende el LED de la tecla Line. La pantalla LCD muestra la cuenta SIP que está utilizando. Cambie estos valores, si lo desea, usando las teclas Line y Account. 2 Compruebe si se escucha el tono de marcado.
ESPAÑOL Poner una llamada en espera Presione la tecla HOLD una vez para colocar una llamada en espera. Presiónela de nuevo para volver a la llamada. Puede realizar una llamada en otra línea (presione otra tecla de línea) y regresar a la llamada en espera. UTILIZAR CORREO DE VOZ Una vez configurado el número de correo de voz de su cuenta SIP en el V500, presione la tecla VOICEMAIL para comprobar sus mensajes.
ESPAÑOL Ver el/los certificado(s) de un producto 1 Vaya a www.zyxel.com. 2 Seleccione su producto de la lista desplegable en la página inicial de ZyXEL para ir a la página de ese producto. 3 Seleccione el certificado que desee visualizar en esta página.
FRANÇAIS Aperçu Au moment de la rédaction, ce guide de mise en route rapide couvre les modèles suivants : • V500 : Téléphone IP. • V501 : Téléphone IP avec PoE (Power over Ethernet). Ce guide de mise en route rapide vous montre comment installer et utiliser votre V500. Il comporte les sections suivantes : • Matériel et connexions - présente les caractéristiques physiques du V500 et vous montre comment le connecter à votre réseau.
FRANÇAIS 1 Matériel et connexions 1 Combiné 2 Ecran LCD 3 Touches du compte 4 Touches programmables 5 Touches de ligne 6 Menu 7 Navigateur 8 Annuaire 9 Touches d'action 10 Clavier alphanumérique 11 Microphone 12 Touches de volume 13 Touches de fonction 14 Touches personnalisées 52
FRANÇAIS Le tableau suivant décrit certaines des caractéristiques matérielles utilisées pour les opérations de base. Voir le chapitre matériel dans votre guide de l'utilisateur pour les descriptions complètes de toutes les caractéristiques. CARACTÉRISTIQUES DESCRIPTION Account keys (Touches du compte) Utilisez celles-ci pour sélectionner le compte SIP que vous désirez utiliser. Vous pouvez configurer jusqu'à quatre comptes SIP sur le V500.
FRANÇAIS CARACTÉRISTIQUES DESCRIPTION Volume keys (Touches de volume) Utilisez la touche + pour augmenter le volume, et utilisez la touche - pour le réduire. • • • Quand vous utilisez le combiné, ces touches contrôlent le volume du micro et de l'écouteur du combiné. Quand vous utilisez le casque, ces touches contrôlent le volume du micro et des écouteurs du casque ( ) et des ports ( ) microphone du V500.
FRANÇAIS Prenez le socle et connectez-le au V500 comme indiqué dans la figure suivante. 1 Insérez d'abord les deux connecteurs sur le côté le plus long du socle. 2 Faites pivoter le socle vers le bas jusqu'à ce que les deux autres connecteurs soient insérés. 3 Tournez le V500 du bon côté vers le haut. Vérifiez que le socle est correctement fixé. 1.
FRANÇAIS 1 WAN : Utilisez un câble Ethernet pour connecter le V500 à votre réseau. V501 seulement : Si vous utiliser PoE (Power over Ethernet), connectez le câble Ethernet fournissant l'alimentation à ce port. Voir Section 1.3 à la page 56 pour les informations sur PoE.
FRANÇAIS 2 Configuration initiale Cette section décrit comment utiliser les menus de l'écran LCD du téléphone pour : • Installation de votre connexion réseau et • Paramétrez votre compte de service vocal Il n'est pas nécessaire de connecter le téléphone à un ordinateur pour cela. " Quand vous entrez les informations, utilisez la touche # pour parcourir de façon cyclique les modes Uppercase (Majuscule), Lowercase (Minuscule), Symbol (Symbole) et Number (Chiffre). Le mode actuel s'affiche sur l'écran LCD.
FRANÇAIS 1 Appuyez sur la touche Menu, et utilisez le navigateur pour sélectionner Advanced Setting (Paramètre avancé). Appuyez sur Select (Sélectionner). Paramètre du Menu 1 Infos système 2 Réglage de la sonnerie 3 Réglage du volume 4 Préférences d'appel 5 Annuaire 6 Paramètre avancé 7 Redémarrer le système 8 Paramètre du logo Sélection " Précéden Vous pouvez aussi utiliser le clavier alphanumérique pour effectuer vos sélections dans l'écran LCD.
FRANÇAIS 2.1.1 Installer PPPoE 1 Si vous avez reçu un nom d'utilisateur et un mot de passe, sélectionnez PPPoE (Inactif) dans le menu Advanced Setting (Paramètre avancé) > Network Setting (Paramètre réseau). Appuyez sur la touche programmable On (Actif) pour que le V500 utilise PPPoE. Paramètre réseau 1 PPPoE (Actif) 2 IP statique (Inactif) 3 DHCP (Inactif) L'écran affiche PPPoE (Actif). Appuyez sur Select (Sélectionner) pour entrer vos informations.
FRANÇAIS 4 Entrez votre mot de passe, allez ensuite à Confirm (Confirmer) et ressaisissez-le. Appuyez sur Save (Enregistrer) quand vous avez terminé. Modifier le mot de passe Actuel : Nouveau : Nouveau mot de passe Confirmer : Nouveau mot de passe Mode Minuscule Enregistr <- Retour 2.1.2 Paramétrer une adresse IP statique 1 Si vous avez une adresse IP à utiliser, sélectionnez Static IP (Off) (IP statique (Inactive)) dans le menu Advanced Setting (Paramètre avancé) > Network Setting (Paramètre réseau).
FRANÇAIS 2 Utilisez les options de ce menu pour entrer les informations d'adresse IP statique, de passerelle et DNS fournies par votre fournisseur de service Internet (ISP) ou l'administrateur réseau. Cliquez sur Back (Retour) pour revenir à l'écran précédent. IP statique 1 Adresse IP 2 Passerelle par défaut 3 Masque de sous-réseau 4 1er DNS 5 2nd DNS Sélection Retour 2.1.3 Obtenir automatiquement une adresse IP " Le V500 est configuré pour obtenir automatiquement une adresse IP par défaut.
FRANÇAIS 2.2 Paramétrez votre compte de service vocal Suivez ces étapes pour configurer votre compte VoIP. 1 Appuyez sur la touche Menu, puis sur 6 pour entrer dans le menu Advanced Setting (Paramètres avancés). 2 Appuyez sur 2 pour entrer dans le menu SIP Configuration (Configuration SIP). 3 Si VoIP 1 Config. n'affiche pas Active (Actif), sélectionnez son entrée et appuyez sur la touche programmable Active (Actif).
FRANÇAIS CHAMP DESCRIPTION 4 SIP Server Addr C'est l'adresse IP du serveur utilisée par votre fournisseur de service VoIP pour les appels SIP. (Adresse du serveur SIP) 5 SIP Server Port (Port du serveur SIP) C'est le port sur le serveur SIP utilisé pour les appels SIP. La valeur par défaut est 5060. 6 SIP Register C'est l'adresse IP du serveur utilisée par votre fournisseur de service Server (Serveur de VoIP pour enregistrer le V500.
FRANÇAIS CHAMP DESCRIPTION 16 Backup SIP Server (Sauvegarder le serveur SIP) Utilisez cela pour paramétrer le(s) serveur(s) SIP que le V500 utilise s'il ne peut accéder au serveur SIP principal. 5 Quand vous avez terminé de configurer SIP 1 Configuration (Configuration SIP 1), appuyez sur Back (Retour). La partie supérieure droite de l'écran LCD affiche le nom du compte SIP que vous avez enregistré (“SIP1”, dans cet exemple).
FRANÇAIS 3 Opération téléphonique Cette section décrit comment utiliser les fonctions téléphoniques de base de votre V500. " Pour plus d'informations sur les fonctions téléphoniques du V500, voir le chapitre concernant le matériel dans votre guide de l'utilisateur. EFFECTUER UN APPEL 1 Décrochez le combiné. Une LED de touche Line (Ligne) s'allume. L'écran LCD montre le compte SIP que vous utilisez. Changez ceux-ci, si vous le désirez, à l'aide des touches Line (Ligne) et Account (Compte).
FRANÇAIS EFFECTUER UN APPEL EN ATTENTE Appuyez sur la touche HOLD (ATTENTE) une fois pour effectuer un appel en attente. Appuyez une seconde fois sur celle-ci pour revenir à l'appel. Vous pouvez effectuer un appel sur une autre ligne (appuyez sur la touche d'une autre ligne) puis retournez sur l'appel en attente.
FRANÇAIS TRANSFÉRER UN APPEL 3 Pour transférer l'appel, vous pouvez : • • Attendre la tonalité, puis poser le combiné, appuyer sur la touche Speaker (Hautparleur) ou sur la touche Headset (Casque) (selon le cas) pour terminer l'appel. Attendez que l'autre personne réponde, puis terminer l'appel. Afficher une (des) certification(s) d'un produit 1 Allez à www.zyxel.com. 2 Sélectionnez votre produit dans la liste déroulante de la page d'accueil de ZyXEL pour aller à la page de ce produit.
FRANÇAIS 68
ITALIANO Cenni generali Alla data di stesura di questa Guida introduttiva, i modelli trattati sono i seguenti: • V500: Telefono IP. • V501: Telefono IP con tecnologia PoE (Power over Ethernet). In questa Guida introduttiva viene spiegato come configurare e utilizzare il V500. In essa sono incluse le sezioni seguenti: • Hardware e collegamenti - Introduce le caratteristiche fisiche del V500 e illustra come collegarlo alla rete.
ITALIANO 1 Hardware e collegamenti 1 Cornetta 2 Schermo LCD 3 Tasti account 4 Tasti contestuali 5 Tasti della linea 6 Menu 7 Navigatore 8 Rubrica 9 Tasti azione 10 Tastiera alfanumerica 11 Microfono 12 Tasti del volume 13 Tasti funzione 14 Tasti personalizzati 70
ITALIANO Nella tabella seguente vengono descritte alcune delle caratteristiche hardware utilizzate per le operazioni di base. Consultare il capitolo sull'hardware nella Guida utente per le descrizioni complete di tutte le caratteristiche e le funzionalità. CARATTERIS TICA DESCRIZIONE Account keys Consentono di selezionare l'account SIP da utilizzare. Sul V500 è possibile (Tasti account) configurare fino a quattro account SIP. Nota: Un account può essere selezionato solo quando è stato configurato.
ITALIANO CARATTERIS TICA DESCRIZIONE Volume keys (Tasti del volume) • Utilizzare il tasto + per aumentare il volume e il tasto - per diminuirlo. • • Quando si utilizza la cornetta, questi tasti controllano il volume di ascolto e di parlato della cornetta stessa. Quando si utilizza l'auricolare, questi tasti controllano il volume di ascolto e di parlato sulle porte auricolare ( ) e microfono ( ) del V500.
ITALIANO Prendere il supporto e collegarlo al V500 come mostrato nella figura seguente. 1 Collegare prima i due connettori del lato più lungo del supporto. 2 Girare il supporto in basso fino a inserire gli altri due connettori. 3 Girare il V500 verso l'alto. Verificare che il supporto sia fissato in modo stabile e sicuro. 1.
ITALIANO 1 WAN: Utilizzare un cavo Ethernet per collegare il V500 alla rete. Solo V501: Se si utilizza la tecnologia Power over Ethernet (PoE), collegare a questa porta il cavo Ethernet che fornisce alimentazione. Vedere Sezione 1.3 a pagina 74 per ulteriori informazioni su PoE.
ITALIANO 2 Configurazione iniziale In questa sezione viene descritto come utilizzare i menu dello schermo LCD del telefono per: • Configurazione della connessione di rete e • Configurazione dell'account voce Per questo non è necessario collegare il telefono a un computer. " Quando si immettono informazioni, utilizzare il tasto # per passare ciclicamente tra le modalità Uppercase (maiuscole), Lowercase (minuscole), Symbol (simboli) e Number (numeri).
ITALIANO Attenersi alla procedura seguente per configurare le impostazioni di rete. 1 Premere il tasto Menu e utilizzare il navigatore per selezionare Advanced Setting (impostazioni avanzate). Premere Select (seleziona).
ITALIANO 2.1.1 Configurazione di PPPoE 1 Se sono stati forniti un nome utente e una password, selezionare PPPoE (Off) nel menu Advanced Setting (impostazioni avanzate) > Network Setting (impostazioni di rete). Premere il tasto contestuale On (attiva) per configurare il V500 affinché utilizzi PPPoE. Impostazioni di rete 1 PPPoE (attivato) 2 IP statico (disattivato) 3 DHCP (disattivato) La schermata visualizza PPPoE (On). Premere Select (seleziona) per inserire le informazioni in proprio possesso.
ITALIANO 4 Immettere la password, passare a Confirm (conferma) e immetterla nuovamente. Premere Save (salva) quando terminato. Modifica password Corrente: Nuovo: Nuova password Conferma: Nuova password Modalità minuscole Salva <- Indietro 2.1.2 Configurazione di un indirizzo IP statico 1 Se si dispone di un indirizzo IP da utilizzare, selezionare Static IP (Off) (IP statico (disattivato)) nel menu Advanced Setting (impostazioni avanzate) > Network Setting (impostazioni di rete).
ITALIANO 2 Utilizzare le opzioni di questo menu per immettere le informazioni relative a indirizzo IP statico, gateway e DNS fornite dal proprio ISP (Internet Service Provider) o dall'amministratore di rete. Premere Back (indietro) per tornare alla schermata precedente. IP statico 1 Indirizzo IP 2 Gateway predefinito 3 Maschera di subnet 4 DNS 1 5 DNS 2 Selezion Indietro 2.1.
ITALIANO 2.2 Configurazione dell'account voce Attenersi alla procedura seguente per configurare l'account VoIP. 1 Premere il tasto Menu e quindi premere 6 per entrare nel menu Advanced Setting (impostazioni avanzate). 2 Premere 2 per entrare nel menu SIP Configuration (configurazione SIP). Configurazione SIP 3 Se l'opzione VoIP 1 Config. (configurazione VoIP 1) non visualizza Active (attiva), selezionare la voce corrispondente e premere il tasto contestuale Active (attiva).
ITALIANO CAMPO DESCRIZIONE 4 SIP Server Addr (indirizzo server SIP) È l'indirizzo IP del server che l'operatore VoIP utilizza per le telefonate SIP. 5 SIP Server Port (porta server SIP) La porta del server SIP utilizzata per le telefonate SIP. La porta predefinita è 5060. 6 SIP Register Server (server di registrazione SIP) È l'indirizzo IP del server che l'operatore VoIP utilizza per registrare il V500.
ITALIANO CAMPO DESCRIZIONE 16 Backup SIP In questo campo è possibile inserire i server SIP che il V500 può Server (server SIP utilizzare nel caso in cui non sia possibile accedere al server SIP di emergenza) principale. 5 Terminata la configurazione in SIP 1 Configuration (configurazione SIP 1), premere Back (indietro). Nella parte superiore destra dello schermo LCD viene visualizzato il nome dell'account SIP registrato (“SIP1” in questo esempio).
ITALIANO 3 Funzionamento del telefono In questa sezione viene descritto come utilizzare le funzioni telefoniche di base del V500. " Per ulteriori informazioni sulle funzioni telefoniche del V500, vedere il capitolo sull'hardware nella Guida utente. FARE UNA TELEFONATA 1 Prendere la cornetta. Un LED di tasto Line (linea) si accende. Lo schermo LCD visualizza l'account SIP che si sta utilizzando. Con i tasti Line (linea) e Account è possibile cambiare questi elementi.
ITALIANO METTERE UNA TELEFONATA IN ATTESA Premere una volta il tasto HOLD (in attesa) per mettere in attesa una telefonata. Premerlo una seconda volta per ritornare alla telefonata. È possibile fare una telefonata su un'altra linea (premere il tasto di un'altra linea) e quindi ritornare alla telefonata in attesa. UTILIZZO DELLA CASELLA VOCALE Dopo aver configurato il numero della casella vocale dell'account SIP del V500, premere il tasto VOICEMAIL (casella vocale) per controllare i messaggi.
ITALIANO TRASFERIMENTO DI CHIAMATA 3 Per trasferire la telefonata è possibile eseguire una delle operazioni seguenti: • • Attendere finché non si sente il tono di squillo, quindi terminare la telefonata mettendo giù la cornetta, premendo il tasto Speaker (altoparlante) o il tasto Headset (auricolare), in base a ciò che si sta utilizzando. Attendere che l'altra persona risponda, quindi terminare la telefonata. Visualizzazione delle certificazioni di un prodotto 1 Aprire la pagina www.zyxel.com.
ITALIANO 86
NEDERLANDS NEDERLANDS Overzicht Deze beknopte handleiding behandelt de volgende modellen: • V500: IP telefoon. • V501: IP telefoon met voeding over Ethernet (PoE). Deze beknopte handleiding toont, hoe u uw V500 instelt en gebruikt. Het omvat de volgende paragrafen: • Hardware en verbindingen - introduceert de fysieke functies van de V500 en toont u hoe die met uw netwerk te verbinden.
NEDERLANDS 1 Hardware en verbindingen 1 Telefoontoestel 2 LCD scherm 3 Accounttoetsen 4 Softtoetsen 5 Lijntoetsen 6 Menu 7 Navigator 8 Telefoonboek 9 Actietoetsen 10 Alphanumeriek toetsenbord 11 Microfoon 12 Volumetoetsen 13 Functietoetsen 14 Aanpassingstoet sen De volgende tabel beschrijft een aantal van de hardware functies die worden gebruikt voor de basis functionaliteiten. Zie het hoofdstuk "hardware" in uw gebruikershandleiding voor de volledige beschrijvingen van alle functies.
NEDERLANDS FUNCTIE BESCHRIJVING Softkeys (softtoetsen) Deze functietoetsen zijn afhankelijk van het huidige scherm in het LCD scherm. Een woord of symbool op het LCD scherm boven een softtoets geven zijn huidige functie weer. Line keys (Lijntoetsen) Druk erop om de telefoonlijn te selecteren die u wilt gebruiken. De V500 heeft vier telefoonlijnen. Menu Druk erop om het configuratiemenu van de V500 weer te geven. Druk er opnieuw op om het menu af te sluiten.
NEDERLANDS Er zijn vier manieren om de bijgevoegde statief te bevestigen, zoals afgebeeld. Als u de V500 wilt opzetten aan de laagste hoek (dichter bij de horizontaal), gebruik de gaten gemarkeerd met 1 in de volgende figuur. Gebruik de gaten gemarkeerd met 2 om de V500 aan de hoogste hoek op te zetten (dichter bij de vertikaal). Neem het statief en verbind het met de V500 zoals weergegeven in de volgende figuur. 1 Plaats de twee connectoren eerst in de langere kant van het statief.
NEDERLANDS 1.2 Achterpaneel Hardwareverbindingen 1 WAN: Gebruik een Ethernetkabel om de V500 te verbinden met uw netwerk. Uitsluitend V501: als u Stroom over Ethernet (PoE) gebruikt, verbind de Ethernetkabel die stroom levert voor deze poort. Zie Section 1.3 on page 92 voor meer informatie over PoE.
NEDERLANDS 1.3 Uitsluitend V501: Stroom over Ethernet (Optioneel) Stroom over Ethernet (PoE) is de mogelijkheid om stroom te bieden aan uw V501 via een 8-pen CAT 5 Ethernetkabel, zonder gebruik te maken van de bijgeleverde stroomadapter. Een PoE injector (niet bijgeleverd) is ook nodig om de Ethernetkabel van stroom te voorzien. Deze mogelijkheid voegt extra flexibiliteit toe ten aanzien van de locatie van uw V501.
NEDERLANDS 2.1 Uw netwerkverbinding instellen Als u uw hardwareverbindingen heeft voltooid, bekijk dan het LCD scherm. De V500 geeft uw Voice over Internet (VoIP) account registratiestatus weer op de tabs aan de rechterkant, en de tijd- en datumdetails in de bovenste sectie. De V500 laat u toe om tot vier VoIP accounts te configureren (ook gekend als SIP accounts). Als een VoIP account niet actief is, verschijnt Ongebruikt.
NEDERLANDS 2 Selecteer Network Setting (Netwerk instelling). Kies uit de volgende opties: Geavanceerde instellingen 1 Netwerkinstelling • Als u een gebruikersnaam en wachtwoord heeft voor toegang tot het netwerk, ga naar paragraaf 2.1.1 op pagina 94. 2 SIP configuratie • Als u een IP adres en subnetmasker heeft, ga naar paragraaf 2.1.2 op pagina 96. 5 Schermafstelling • Als u een IP adres en subnetmasker heeft, ga naar paragraaf 2.1.3 op pagina 96.
NEDERLANDS 3 Het scherm PPPoE Gebruikersnaam verschijnt. Druk op Edit (Bewerken) en voer uw gebruikersnaam in. (Druk op de toets # om te schakelen tussen de invoermodi Number (Nummer), Uppercase (Hoofdletters), Lowercase (Kleine letters) en Symbol (Symbool). PPPoE Gebruikersnaam Nummer Huidige: Nieuw: Gebruiker123 Druk op Opslaan als u klaar bent, en druk vervolgens op 2 om het scherm PPPoE wachtwoord te openen. Druk op Bewerken.
NEDERLANDS 2.1.2 Een Statisch IP Adres instellen 1 Als u een IP adres heeft, selecteer Statisch IP (Uit) in het menu Geavanceerde instellingen > Netwerkinstelling. Druk op de softtoets Aan om de V500 een statisch IP adres te doen gebruiken. Netwerkinstelling 1 PPPoE (Uit) 2 Statisch IP (Aan) 3 DHCP (Uit) Het scherm toont IP (Aan). Druk op Selecteren om uw informatie in te voeren.
NEDERLANDS 2.2 Uw Voice Account instellen Volg deze stappen om uw VoIP account te configureren. 1 Druk op de toets Menu, en vervolgens op 6 om het menu Advanced Setting (Geavanceerde instellingen) te openen. 2 Druk op 2 om het menu SIP Configuration (SIP?configuratie) te openen. 3 Als VoIP 1 Config. niet Actief toont, selecteer dan zijn invoer en druk op de softtoets Actief. Als het SIP account niet actief is, kunt u dit niet gebruiken of telefoongesprekken ontvangen. SIP Configuratie 1 VoIP 1 Config.
NEDERLANDS VELD BESCHRIJVING 6 SIP Register Server (SIP registerserver) Dit is het IP adres van de server dat uw VoIP service provider gebruikt om de V500 te registreren. Als uw VoIP service provider geen specifiek SIP register serveradres geeft, voer het SIP Serveradres opnieuw in. 7 SIP Register Port (SIP Registerpoort) Dit is de poort die de SIP registerserver gebruikt om de V500te registreren. De standaardwaarde is 5060.
NEDERLANDS V Als uw SIP account niet probleemloos registreert (Ongebruikt of No Reg blijft op het hoofdscherm staan) of u kunt niet bellen, controleer uw verbindingen en over uw SIP instellingen opnieuw in. Start de V500 opnieuw (schakel stroom uit, en opnieuw in). Als dit niet helpt, neem contact op met uw netwerkbeheerder of VoIP service provider. 3 Telefoonwerking Deze paragraaf beschrijft hoe de basis telefoonfuncties van uw V500 te gebruiken.
NEDERLANDS EEN GESPREK BEËINDIGEN Als u een gesprek wilt beëindigen, druk op de toets HANG UP (OPHANGEN). Anderzijds doet u één van de volgende: • Als u de hoorn gebruikt, plaats het terug op de haak. • Als u de interne luidspreker gebruikt, druk op de toets SPEAKER (LUIDSPREKER). • Als u een externe hoofdtelefoon gebruikt, druk op de toets HEADSET (HOOFDTELEFOON). EEN OPROEP IN WACHTSTAND PLAATSEN Druk éénmaal op de toets HOLD om een oproep in wachtstand te plaatsen.
NEDERLANDS EEN OPROEP OVERDRAGEN Onderneem de volgende stappen om een gesprek over te dragen naar een ander telefoonnummer. 1 Tijdens het gesprek, druk op de toets Transfer (Overdragen). De volgende beschikbare lijn activeert automatisch. Zorg ervoor dat u een kiestoon kunt horen. 2 Kies het nummer waarnaar u de oproep wilt overdragen.
NEDERLANDS 102
РУССКИЙ Важная информация Прилагаемая документация Прежде чем приступить к подключению IP-телефона ZyXEL серии V500, внимательно ознакомьтесь с прилагаемой документацией. В руководстве рассматриваются следующие модели, доступные на момент его подготовки: • V500-T1: IP-телефон; • V501-T1: IP-телефон с питанием по Ethernet (PoE). Настоящее руководство содержит базовые сведения, необходимые для подключения и начала работы.
РУССКИЙ Срок службы Установленный производителем в порядке п. 2 ст. 5 Федерального закона РФ "О защите прав потребителей" срок службы изделия равен 5 годам с даты производства при условии, что изделие используется в строгом соответствии с настоящим руководством и применимыми техническими стандартами. Юридический адрес изготовителя Зайксел Коммуникэйшнз Корп., Инновэйшн Роад II, 6, Сайнс-бейсд Индастриал Парк, Син-Чу, Тайвань ZyXEL Communications Co.
РУССКИЙ 1 Оборудование и подключения 1 Трубка 2 ЖК-дисплей 3 Клавиши учетной записи 4 Программные клавиши 5 Клавиши линии 6 Меню 7 Навигатор 8 Клавиша телефонной книги 9 Клавиши операций 10 Алфавитноцифровая клавиатура 11 Микрофон 12 Клавиши регулировки громкости 13 Функциональные клавиши 14 Настраиваемые клавиши 105
РУССКИЙ В следующей таблице описаны функции оборудования, используемые для основных операций. Подробное описание всех функций см. в главе об оборудовании в руководстве пользователя. ФУНКЦИЯ ОПИСАНИЕ Клавиши учетной записи Служат для выбора используемой учетной записи SIP. V500 позволяет настроить до четырех учетных записей SIP. Примечание. Учетную запись можно выбрать только после ее настройки (для создания учетной записи войдите на дисплее телефона в меню Advanced Setting > SIP Configuration).
РУССКИЙ ФУНКЦИЯ ОПИСАНИЕ Клавиши регулировки громкости • Громкость увеличивается клавишей + и уменьшается клавишей -. • • В случае использования телефонной трубки эти клавиши регулируют громкость микрофона и динамика в трубке. В случае использования гарнитуры эти клавиши регулируют громкость для портов наушников ( ) и микрофона ( ) на V500. Если телефон используется в режиме громкой связи, эти клавиши регулируют громкость внутреннего динамика и микрофона (Mic). 1.
РУССКИЙ Закрепите подставку в корпусе V500, как показано на следующем рисунке. 1 Сначала проденьте в пазы два выступа с более длинной стороны подставки. 2 Наклоните подставку вниз, чтобы в пазы вошли два других выступа. 3 Переверните V500 лицевой стороной вверх. Убедитесь, что подставка надежно закреплена в корпусе.
РУССКИЙ 1.2 Подключение оборудования к задней панели 1 WAN: для подключения V500 к сети используйте кабель Ethernet. Только в модели V501: если используется питание по Ethernet (PoE), подключите к этому порту Ethernet-кабель, по которому будет подаваться питание. Технология PoE более подробно описана в разделе 1.3 на стр. 110.
РУССКИЙ 1.3 Только в модели V501: питание по Ethernet (по усмотрению пользователя) Технология питания по Ethernet (PoE) позволяет подвести питание к V501 по 8-жильному кабелю Ethernet категории 5, что исключает необходимость поиска дополнительных источников питания. Чтобы ввести питание в Ethernet-кабель, необходим специальный адаптер-инжектор PoE (в комплекте с телефоном не поставляется). PoE предоставляет больше свободы в выборе места размещения V501.
РУССКИЙ " При вводе информации клавиша # переключает клавиатуру между режимом заглавных букв (Uppercase), режимом строчных букв (Lowercase), режимом специальных символов (Symbol) и цифровым режимом (Number). Текущий режим отображается на дисплее. Чтобы выбрать один из нескольких символов, нажмите клавишу несколько раз. Например, чтобы набрать Z в режиме ввода заглавных букв (Uppercase), четыре раза нажмите клавишу «9». 2.
РУССКИЙ 1 Нажмите клавишу Menu и с помощью навигатора выберите Advanced Setting. Нажмите Select. Menu Setting 1 System Info 2 Ring Setting 3 Volume Setting 4 Call Preference 5 Phonebook 6 Advanced Setting 7 System Restart 8 Feature Code Show Select " Back Для выбора параметров на экране можно также использовать алфавитно-цифровую клавиатуру. Например, для перехода на экран Advanced Setting можно нажать клавишу 6 на показанном выше экране Menu Setting. 2 Выберите Network Setting.
РУССКИЙ 2.1.1 Настройка PPPoE 1 Если вам были предоставлены имя пользователя и пароль, в меню Advanced Setting > Network Setting выберите PPPoE (Off). Чтобы разрешить V500 использовать протокол PPPoE, нажмите программную клавишу On. Network Setting 1 PPPoE (On) 2 Static IP (Off) 3 DHCP (Off) На дисплее появится сообщение: PPPoE (On). Чтобы ввести информацию о сетевом подключении, нажмите Select. Select 2 Чтобы ввести имя пользователя для учетной записи, нажмите 1.
РУССКИЙ 4 Введите пароль, затем перейдите в поле Confirm и введите его повторно. После ввода пароля нажмите Save. Edit Password Current: New: NewPassword Confirm: NewPassword Lowercase mode Save <- Back 2.1.2 Настройка статического IP-адреса 1 Если вам был предоставлен IP-адрес, выберите Static IP (Off) в меню Advanced Setting > Network Setting. Чтобы настроить V500 для использования статического IPадреса, нажмите программную клавишу On.
РУССКИЙ 2 Это меню служит для ввода статического IPадреса, адреса шлюза и параметров DNSсервера, предоставленных поставщиком услуг Интернета или администратором сети. Для возврата на предыдущий экран нажмите Back. Static IP 1 IP Address 2 Default Gateway 3 Subnet Mask 4 1st DNS 5 2nd DNS Select Back 2.1.3 Автоматическое получение IP-адреса " По умолчанию V500 настроен на автоматическое получение IP-адреса.
РУССКИЙ 2 Нажмите клавишу 2, чтобы войти в меню SIP Configuration. 3 Если для конфигурации VoIP 1 Configuration не отображается статус Active («активна»), выберите соответствующую запись и нажмите программную клавишу Active. Если учетная запись SIP неактивна, она не может использоваться для исходящих или входящих вызовов.
РУССКИЙ ПОЛЕ ОПИСАНИЕ 6 SIP Register Server Это IP-адрес сервера, используемого поставщиком услуг VoIP для регистрации V500. Если поставщик услуг VoIP не сообщил отдельного адреса сервера регистрации SIP, то снова введите в этом поле адрес, указанный в поле SIP Server. 7 SIP Register Port Это номер порта, используемый устройством V500 для регистрации на сервере SIP. Значение по умолчанию – 5060. 8 SIP Service Domain Если ваша учетная запись SIP имеет вид 1234567@voipprovider.
РУССКИЙ 5 Завершив настройку конфигурации SIP 1 Configuration, нажмите Back. В правой верхней части экрана отобразится имя зарегистрированной учетной записи SIP («SIP1» в данном примере). 6 Чтобы сделать вызов для проверки конфигурации V500, см. раздел 3. 11:45 2006-12-12 SIP 1 ZyXEL Unused Unused Unused V Если не удается зарегистрировать учетную запись (на дисплее продолжает присутствовать сообщение Unused или No Reg) или осуществить вызов, проверьте подключения и повторно введите настройки SIP.
РУССКИЙ ВХОДЯЩИЙ ВЫЗОВ Ответить на входящий вызов можно одним из следующих способов: • Для разговора с использованием телефонной трубки снимите трубку. • Чтобы ответить в режиме громкой связи, нажмите клавишу SPEAKER. • Чтобы ответить с использованием внешней гарнитуры, нажмите клавишу HEADSET. ЗАВЕРШЕНИЕ ВЫЗОВА Чтобы завершить вызов, нажмите клавишу HANG UP. Завершить вызов также можно другими способами: • Если вы разговариваете используя телефонную трубку, положите ее на базу телефона.
РУССКИЙ ВЫЗОВ В РЕЖИМЕ КОНФЕРЕНЦСВЯЗИ 2 Убедитесь, что вызов активен (вы можете разговаривать с абонентом на другой стороне). Нажмите клавишу Conference. Первый вызов будет «отмечен» для включения в конференц-связь. 3 Нажмите клавишу Line для другой линии. Теперь можно принять входящий вызов, осуществить еще один исходящий вызов или удалить существующий вызов, ранее переведенный в режим ожидания. 4 Убедитесь, что вызов активен, и снова нажмите клавишу Conference.
РУССКИЙ • Независимо от даты продажи срок гарантии не может превышать четыре с половиной года с даты производства изделия. Дата производства определяется по серийному номеру на корпусе изделия. Формат серийного номера: SYYxxWWxxxxxx, где YY последняя цифра или две цифры года производства, WW - номер недели производства в году. • Настоящая гарантия распространяется только на изделия ZyXEL, проданные через официальные каналы дистрибуции ZyXEL.
РУССКИЙ Контактная информация Центр информации и поддержки ZyXEL В Интернете Бесплатные телефонные номера Россия zyxel.ru/help 8-800-200-8929 из Москвы: (495) 542-8929 Беларусь zyxel.by/help Казахстан zyxel.kz/help 8-800-080-0055 Узбекистан zyxel.kz/help 8-800-120-0500 Украина 8-800-504-0040 ua.zyxel.com/help Представительства Адреса и телефоны ZyXEL Россия 117279, Москва, ул. Островитянова, 37а http://zyxel.ru (495) 542-8920 ZyXEL Беларусь 220123, Минск, ул. В.
简体中文 概述 编写此快速开始指南时,涵盖以下型号: tV500: IP 电话。 tV501: 以太网供电 IP 电话 (PoE)。 本快速开始指南为您解释如何设置和使用 V500。它包括以下章节: t 硬件和连接 - 介绍 V500 的实际功能并解释如何将其连接到网络。 t 初始配置 - 讨论如何使用 V500 的 LCD 屏幕和键盘设置网络配置和 SIP 服务器注册。 t 电话操作 - 涵盖如何使用 V500 的基本电话功能,例如拨出呼叫。 也可以使用与 V500 的 PC 端口相连的电脑通过 Web 配置程序来配置 V500。详细信息请参阅 用户指南。 123
简体中文 1 硬件和连接 1 手机 2 LCD 屏幕 3 帐户键 4 软键 5 线路键 6 菜单 7 导航器 8 电话簿 9 动作键 10 字母数字键盘 11 麦克风 12 音量按键 13 功能键 14 自定义键 下表说明基本操作中所使用的某些硬件功能。关于所有功能的完整说明,请参阅用户指南中 的硬件章节。 特征 说明 Account keys ( 帐户键 ) 使用这些键选择想要使用的 SIP 帐户。最多可以在 V500 上配置四个 SIP 帐 户。 Note: 帐户只能在已配置后选择 (使用 Advanced Setting ( 高级设置 )> SIP Configuration (SIP 配置 ) LCD 屏幕 菜单配置帐户)。 Softkeys ( 软 键) 这些键的功能取决于当时显示在 LCD 屏幕上的屏幕。LCD 屏幕在软键上方显 示的字词或符号说明当前功能。 124
简体中文 特征 说明 Line keys ( 线 按这些键选择想要使用的电话线路。 V500 具有四条电话线路。 路键 ) Menu ( 菜单 ) 按此键显示 V500 的配置菜单。再按一次退出菜单。呼叫过程中无法访问菜 单。 Navigator 导航器 ) 按这些键在 V500 屏幕中移动。按 在菜单上上移一栏,按 下移一栏。按 向右移动一格,按 向左移动一格。也可以按 进行菜单选择,按 返回 前一菜单。 ( Phonebook ( 电 使用此项显示存储在 V500 中的联系人列表。可以从此屏幕添加、编辑和删 话簿 ) 除电话簿项。 Alphanumeric keypad ( 字母 数字键盘 ) 使用这些键输入数字、字母和符号。使用 # 键在 Number ( 数字 ) 模式、 Uppercase ( 大写字母 ) 模式 、Lowercase ( 小写字母 ) 模式和 Symbol ( 符号 ) 模式间切换。 Microphone ( 麦克风 ) 当 V500 处于扩音器模式时麦克风激活。 Volume keys ( 音量按键 ) 使用 + 键调高音量,使用 - 键调低音量。 t 使
简体中文 如果想要以低角度 (更接近水平)支起 V500,请使用下图中 标为 1 的孔。要以高角度 (更接近垂直)支起 V500,请使用 标为 2 的孔。 取出支架,如下图所示将它连接到 V500。 1 先将两个接头插在支架长边上。 2 将支架向下转动,直至另外两个接头插入。 3 将 V500 向上折起。检查支架是否安装牢固。 126
简体中文 1.2 后面板硬件连接 1 WAN: 使用以太网线将 V500 连接到网络。 仅限 V501: 如果正在使用以太网供电 (PoE),将供电的以太网线连接到此端口。有关 PoE 的更多信息,请参阅 Section 1.
简体中文 1.
简体中文 2.1 设置网络连接 完成硬件连接后,查看 LCD 屏幕。 V500 会在右部选 项卡内显示互联网语音 (VoIP) 帐户注册状态,并且 顶部选项卡内显示时间和日期详细信息。 V500 允许您配置最多四个 VoIP 帐户(也称为 SIP 帐户)。VoIP 帐户未激活时,显示 Unused ( 未用 )。帐户激活但未成功注册时,选项卡内显示 No Reg ( 未注册 )。帐户激活且注册成功,选项卡显示帐户 名称 ( 此范例中为 SIP 1)。 V 11:45 2008-12-12 SIP 1 ZyXEL 未用 未用 未用 如果 LCD 屏幕无任何显示,请重新检查硬件连接。请参阅第 1.
简体中文 2 选择 Network Setting ( 网络设置 )。 高级设置 从以下选项选择: 1 网络设置 t 如果已得到访问网络所需的用户名和密码,请 跳至第 130 页的 2.1.1 一节。 2 SIP 配置 t 如果已得到可用 IP 地址和子网掩码,请跳至第 132 页的 2.1.2 一节。 4 可编程键 t 如果无可用 IP 地址,请跳至第 132 页的 2.1.3 一节。 6 呼叫功能模式 3 自动提供 ( 关 ) 5 显示调整 7 语言支持 选择 后退 2.1.
简体中文 3 显示 PPPoE Username (PPPoE 用户名 ) 屏幕。按 Edit ( 编辑 ) 并输入您的用户名。(按 # 键在 Number ( 数字 )、Uppercase ( 大写字母 )、 Lowercase ( 小写字母 ) 和 Symbol ( 符号 ) 输 入模式间循环。) 完成后按 Save ( 保存 ),然后按 2 进入 PPPoE Password (PPPoE 密码 ) 屏幕。按 Edit ( 编辑 )。 4 输入密码,然后下移至 Confirm ( 确认 ),重新 输入密码。完成后再次按 Save ( 保存 )。 PPPoE 用户名 号 帐 当前: 新: 用户 123 保存 <- 后退 <- 后退 编辑密码 当前: 新: 新密码 确认: 新密码 小写字母模式 保存 131
简体中文 2.1.2 设置静态 IP 地址 1 如果有可用 IP 地址,在 Advanced Setting ( 高 级设置 ) > Network Setting ( 网络设置 ) 菜单 中选择 Static IP (Off) ( 静态 IP ( 关 ))。按 On ( 开 ) 软键使 V500 使用静态 IP 地址。 屏幕显示 Static IP (On) ( 静态 IP ( 开 ))。按 Select ( 选择 ) 输入您的信息。 网络设置 1 PPPoE ( 关 ) 2 静态 IP ( 开 ) 3 DHCP ( 关 ) 选择 2 使用本菜单中的选项输入互联网服务提供商 (ISP) 或网络管理员所提供的静态 IP 地址、网 关和 DNS 信息。按 Back ( 后退 ) 返回前一菜 单。 后退 静态 IP 1 IP 地址 2 默认网关 3 子网掩码。 4 第一 DNS / DNS 5 第二 DNS / DNS 选择 2.1.
简体中文 2.2 设置语音帐户 依照下列步骤来配置 VoIP 帐户。 1 按 MENU ( 菜单 ) 键,然后按 6 进入 Advanced Setting ( 高级设置 ) 菜单。 2 按 2 进入 SIP Configuration (SIP 配置 ) 菜 单。 3 如果 VoIP 1 Config.
简体中文 字段 说明 6 SIP Register Server (SIP 注册 服务器 ) 这是 VoIP 服务提供商用来注册 V500 的服务器的 IP 地址。如果 VoIP 服务提供商未给您提供具体 SIP 注册服务器地址,请再次输入 SIP Serv (SIP 服务器 ) 地址。 7 SIP Register Port (SIP 注册端 口) 这是 SIP 注册服务器用来注册 V500 的端口。默认为 5060。 8 SIP Service Domain (SIP 服务 域名 ) 例如,如果您的 SIP 帐户是 1234567@voip-provider.com,则 SIP Service Domain (SIP 服务域名 ) 是 voip-provider.
简体中文 5 完成 SIP 1 Configuration (SIP 1 配置 ) 配置 后,按 Back ( 后退 )。LCD 屏幕右上部分会显 示已注册的 SIP 帐户名称 (在此范例中为 “SIP1”)。 6 有关如何通过呼叫测试您的 V500 的配置,请参阅 3。 7 11:45 2006-12-12 SIP 1 ZyXEL 未用 未用 未用 V 如果未成功注册 SIP 帐户(Unused ( 未用 ) 或 No Reg ( 未注册 ) 仍显示在 主屏幕中)或者无法拨出呼叫,请检查连接并重新输入 SIP 设置。重启 V500 (关闭电源,然后重新开机)。如果此措施无用,请联系网络管理员或 VoIP 服务提供商。 3 电话操作 本节说明如何使用 V500 的基本电话功能。 " 有关 V500 电话功能的更多信息,请参阅用户指南中的硬件章节。 拨出呼叫 1 取出手机。 Line ( 线路 ) 键 LED 点亮。LCD 屏幕显示正在使用哪一 SIP 帐户。如果需要,更 改这些 Line ( 线路 ) 和 Account ( 帐户 ) 键。 2 检查能否听到拨号音。 3 输入想要呼
简体中文 接收呼叫 电话响铃时,按下列步骤之一操作: t 取出手机,使用手机接收呼叫。 t 按 SPEAKER ( 扬声器 ) 键,使用内部扩音器接收呼叫。 t 按 HEADSET ( 耳机 ) 键,使用外部耳机接收呼叫。 结束呼叫 想要结束呼叫时,按 HANG UP ( 挂机 ) 键。或者按下列步骤之一操作: t 如果正在使用手机,将手机放回座机。 t 如果正在使用内部扩音器,按 SPEAKER ( 扬声器 ) 键。 t 如果正在使用外部耳机,按 HEADSET ( 耳机 ) 键。 保持呼叫 按一次 HOLD ( 保持 ) 键保持呼叫。按第二次可返回呼叫。可在另一条线上拨出呼叫 (按另 一线路键),然后返回保持的呼叫。 使用语音邮件 在 V500 上配置 SIP 帐户的语音邮件帐号后,按 VOICEMAIL ( 语音邮件 ) 键可检查消息。 使用 Advanced Setting ( 高级设置 )> SIP Configuration (SIP 配置 )> SIP 1 ~ 4 Configuration (SIP 1 ~ 4 配置 )> Voicemail Number ( 语音邮件帐号 ) 菜单设置语音
简体中文 转接呼叫 请按以下步骤将来电转接至另一电话号码。 1 来电过程中,按 Transfer ( 转接 ) 键。下一可用线路自动启动。确保可听到拨号音。 2 拨打您想要转接呼叫的号码。 3 要转接呼叫,可: t 等待听见响铃音,放下手机,按 Speaker ( 扬声器 ) 键或 Headset ( 耳机 ) 键 (取决于正在使用的模式)结束呼叫。 t 等待另一方接听,然后结束呼叫。 查看产品证书 1 先访问 www.zyxel.
简体中文 138
繁體中文 繁體中文 概覽 在本文撰寫時,此 《快速入門指引》涵蓋以下型號: • V500: IP 電話。 • V501: 乙太網路供電 (PoE) 的 IP 電話。 本 《快速入門指引》說明如何設定及使用 V500。內容包含下列章節: • 硬體與連接 - 介紹 V500 的實體功能,並說明如何連接至網路上。 • 初始設定 - 討論如何使用 V500 的 LCD 螢幕及按鍵,設定網路及 SIP 伺服器註冊。 • 電話操作 - 涵蓋如何使用 V500 的基本電話功能,例如撥打電話。 您也可以透過網頁設定介面,使用電腦連接至 V500 的 PC 埠以設定 V500。詳細資訊請參閱 《使用手冊》。 139
繁體中文 1 硬體與連接 1 話筒 2 LCD 畫面 3 帳號按鍵 4 螢幕鍵盤 5 線路按鍵 6 選單 7 導覽 8 電話簿 9 動作按鍵 10 字母與數字按 鍵 11 麥克風 12 音量鍵 13 功能按鍵 14 自訂按鍵 下表說明某些用作基本操作的硬體功能。請參閱 《使用手冊》的硬體章節中,所有功能的完 整說明。 功能 說明 Account keys ( 帳號按鍵 ) 使用這些按鍵選取所要使用的 SIP 帳號。您可在 V500 上設定多達四組 SIP 帳號。 注意: 您只能選取已經設定好的帳號 (使用 Advanced Setting (進階設定)> SIP Configuration (SIP 設定)LCD 螢幕選單來設定帳號)。 Softkeys ( 螢 幕鍵盤 ) 這些按鍵的功能係根據目前顯示在 LCD 螢幕上的畫面。在 LCD 螢幕的螢幕 鍵盤上方所顯示的字組或符號,即顯示其目前功能。 140
繁體中文 功能 說明 Line keys ( 線 使用這些按鍵選取所要使用的電話線路。此 V500 有四條電話線路。 路按鍵 ) Menu ( 選單 ) 按此以顯示 V500 的設定選單。再按一下可離開選單。當通話正在進行時, 選單即無法存取。 Navigator ( 導 按下這些鍵可在 V500 的畫面上游移。按一下 在選單中上移一行,按一 覽 ) 下 則可下移一行。按一下 向右移動一個空格,按一下 向左移動 一個空格。也可以按一下 進行選單選取,按一下 則返回上一個選 單。 Phonebook ( 電 用它來顯示儲存在 V500 裡的聯絡人清單。您可從此畫面新增、編輯及刪除 話簿 ) 電話簿項目。 Alphanumeric keypad ( 字母 與數字按鍵 ) 使用這些按鍵輸入數字、字母及符號。使用 # 按鍵在 Number ( 數字模式 )、Uppercase ( 大寫模式 )、Lowercase ( 小寫模式 )、及 Symbol ( 符號模 式 ) 之間切換。 Microphone ( 麥克風 ) 當 V500 處於免持聽筒模式時,麥克風即啟用。 Volume keys ( 音量鍵
繁體中文 如果想要讓 V500 以較低角度站立 (接近水平),請使用下圖 所示標示 1 的圓孔。使用標示 2 的圓孔,讓 V500 以較高角 度站立 (接近垂直)。 如下圖所示,取出腳架並連接至 V500。 1 先將兩個接頭插入腳架較長的一側。 2 將腳架向下轉直到另兩個接頭也插入為止。 3 將 V500 往右邊向上旋轉。檢查腳架是否已經牢固安裝。 142
繁體中文 1.2 後面板硬體連接 1 WAN: 使用乙太網路線將 V500 連接至網路。 僅限 V501: 如果您正在使用乙太網路供電 (PoE),連接的乙太網路線將供應電源至此連接 埠。請參閱 第 144 頁的第 1.
繁體中文 1.
繁體中文 2.1 設定網路連接 當硬體連接完成後,注視 LCD 螢幕。V500 在右邊的 索引標籤上顯示網際網路語音 (VoIP) 帳號註冊狀 態,詳細的時間與日期則顯示在頂部。 V500 能設定多達四組 VoIP 帳號 (也稱為 SIP 帳 號)。若 VoIP 帳號並未啟用,則顯示 Unused ( 未使 用 )。當帳號已啟用但尚未成功註冊,會在索引標籤 顯示 No Reg。當帳號已啟用且成功註冊,索引標籤 會顯示帳號名稱 (如本例的 SIP 1)。 V 11:45 2008-12-12 SIP 1 ZyXEL 未使用 未使用 未使用 若 LCD 螢幕未顯示任何資訊,請重新檢查硬體連接。請參閱第 1.
繁體中文 2 選取 Network Setting ( 網路設定 )。 進階設定 從下列選項選取: 1 網路設定 • 若有提供使用者名稱及密碼存取網路,則前往 146 頁的第 2.1.1 節。 2 SIP 設定 3 自動提供 (關閉) • 若有提供 IP 位址及子網路遮罩以供使用,則前往 148 頁的第 2.1.2 節。 4 可程式按鍵 • 若未提供 IP 位址使用,請前往 148 頁的第 2.1.3 節。 6 呼叫功能模式 5 顯示調整 7 支援的語系 選取 上一步 2.1.
繁體中文 3 顯示 PPPoE Username (PPPoE 使用者名稱 ) 畫 面。按一下 Edit 並輸入您的使用者名稱。 (按 一下 # 按鍵在 Number ( 數字 )、Uppercase ( 大 寫 )、Lowercase ( 小寫 )、及 Symbol ( 符號 ) 項目模式之間切換。) 完成時請按一下 Save ( 儲存 ),接著按一下 2 以 進入 PPPoE Password (PPPoE 使用者名稱 ) 畫 面。按一下 Edit ( 編輯 )。 4 輸入密碼,接著往下前往 Confirm ( 確認 ) 並重 新輸入。完成之後按一下 Save ( 儲存 )。 PPPoE 使用者名稱 號碼 目前: 新增: User123 儲存 <- 上一步 <- 上一步 編輯密碼 目前: 新增: NewPassword 確認: NewPassword 小寫模式 儲存 147
繁體中文 2.1.2 設定靜態 IP 位址 1 若有 IP 位址可用,請選取 Advanced Setting (進階設定) > Network Setting (網路設定) 選單中的 Static IP (Off) ( 靜態 IP 開啟 )。按 一下螢幕鍵盤的 On ( 開啟 ) 可讓 V500 使用靜 態 IP 位址。 網路設定 1 PPPoE (關閉) 2 靜態 IP (開啟) 3 DHCP ( 關閉 ) 螢幕顯示 Static IP (On)。( 靜態 IP 關閉 ) 按一 下 Select ( 儲存 ) 以輸入資訊。 選取 2 使用本選單中的選項,輸入由網際網路服務供應 商 (ISP) 或網路管理員提供的靜態 IP 位址、閘 道及 DNS 資訊。按一下 Back ( 上一步 ) 可回到 上一個畫面。 上一步 靜態 IP 1 IP 位址 2 預設閘道 3 子網路遮罩 4 第一組 DNS 5 第二組 DNS 選取 2.1.
繁體中文 2.2 設定語音帳號 遵循這些步驟設定 VoIP 帳號。 1 按一下 Menu ( 選單 ) 按鍵,接著按一下 6 以進入 Advanced Setting ( 進階設定 ) 選 單。 2 按一下 2 進入 SIP Configuration (SIP 設定 ) 選單。 3 如果 VoIP 1 Config.
繁體中文 欄位 說明 6 SIP Register Server (SIP 註冊 伺服器 ) 這是 VoIP 服務供應商的 IP 位址,用來註冊 V500。如果 VoIP 服務供 應商並未提供指定的 SIP 註冊伺服器位址,請再次輸入 SIP Server (SIP 伺服器 ) 位址。 7 SIP Register Port (SIP 註冊埠 ) 這是 SIP 註冊伺服器用來註冊 V500 的連接埠。預設為 「5060」。 8 SIP Service Domain (SIP 服務 網路 ) 如果您有 1234567@voip-provider.com 之類的 SIP 帳號,則 Service Domain (SIP 服務網路 ) 是 voip-provider.
繁體中文 5 完成設定 SIP 1 Configuration (SIP 設定 ) 之 後,按一下 Back ( 上一步 ) 。LCD 螢幕的右上 角會顯示您註冊的 SIP 帳號 (本例中為 「SIP1」)。 6 請參閱第 3 節,如何透過撥打電話測試您的 V500 設定。 11:45 2006-12-12 SIP 1 ZyXEL 未使用 未使用 未使用 V 如果 SIP 帳號並未成功註冊 (Unused 或 No Reg 仍顯示在主畫面上)、或 您無法撥打電話,請檢查連接並重新輸入 SIP 設定。重新啟動 V500 (關閉 電源再重新開機)。若仍無法運作,請連繫網路管理員或 VoIP 服務供應 商。 3 電話操作 本節說明如何使用 V500 的基本電話功能。 " 有關 V500 電話功能的更多資訊,請參閱 《使用手冊》中硬體一章的說明。 撥打電話 1 拿起話筒。 某一 Line ( 線路 ) 按鍵的 LED 亮起。LCD 螢幕將顯示正在使用的 SIP 帳號。必要時 可使用 Line ( 線路 ) 及 Account ( 帳號 ) 按鍵變更這些。 2 檢查是否能聽到撥號聲。 3 輸
繁體中文 接聽電話 電話響起鈴聲時,執行下列任一動作: • 拿起話筒,使用話筒接聽電話。 • 按一下 SPEAKER ( 喇叭 ) 按鍵,使用內部免持聽筒接聽電話。 • 按一下 HEADSET ( 耳機 ) 按鍵,使用外部話筒接聽電話。 結束通話 要結束通話時,按一下 HANG UP ( 掛上 ) 按鍵。或者,執行下列任一動作: • 若您使用話筒,則掛回話機。 • 若您使用內部免持聽筒,按一下 SPEAKER ( 喇叭 ) 按鍵。 • 若您使用外部話筒,按一下 HEADSET ( 耳機 ) 按鍵。 保留通話 按一下 HOLD ( 保留 ) 按鍵將通話保留。按第二下可回復通話。您可使用另一條線路撥號 (按下另一條線路的按鍵),然後再返回先前保留的通話。 使用語音信箱 一旦您已在 V500 設定好了 SIP 帳號的語音信箱,即可按一下 VOICEMAIL ( 語音信箱 ) 按鍵 檢查您的訊息。 使用 Advanced Setting ( 進階設定 ) > SIP Configuration (SIP 設定 ) > SIP 1 ~ 4 Configuration (SIP1 ~ 4 設定 ) > Voicem
繁體中文 來電轉接 採取以下步驟可將來電轉接到另一個電話號碼。 1 在轉接的過程,按一下 Transfer ( 轉接 ) 按鍵。下一條適用的線路會自動啟用。確認 能夠聽到撥號聲。 2 撥打您想要轉接的電話號碼。 3 欲轉接來電,您可: ? ? 等候響鈴聲響起,然後才掛上話筒,按一下 Speaker ( 喇叭 ) 按鍵或 Headset ( 耳 機 ) 按鍵 (根據您正使用的方式)結束通話。 等候有其他人回應電話,然後才結束通話。 查看產品的認證資料 1 前往 www.zyxel.
繁體中文 154