Operation Manual
Table Of Contents
- VMG4825-B10A
- User’s Guide
- Introducing the VMG
- The Web Configurator
- Quick Start
- Tutorials
- 4.1 Overview
- 4.2 Setting Up an ADSL PPPoE Connection
- 4.3 Setting Up a Secure Wireless Network
- 4.4 Setting Up Multiple Wireless Groups
- 4.5 Configuring Static Route for Routing to Another Network
- 4.6 Configuring QoS Queue and Class Setup
- 4.7 Access the VMG Using DDNS
- 4.8 Configuring the MAC Address Filter
- 4.9 Access Your Shared Files From a Computer
- Technical Reference
- Network Map and Status Screens
- Broadband
- Wireless
- Home Networking
- Routing
- Quality of Service (QoS)
- Network Address Translation (NAT)
- Dynamic DNS Setup
- VLAN Group
- Interface Grouping
- USB Service
- Firewall
- MAC Filter
- Parental Control
- Scheduler Rule
- Certificates
- Log
- Traffic Status
- ARP Table
- Routing Table
- Multicast Status
- xDSL Statistics
- System
- User Account
- Remote Management
- SNMP
- Time Settings
- E-mail Notification
- Log Setting
- Firmware Upgrade
- Backup/Restore
- Diagnostic
- Troubleshooting
- Appendices
Chapter 6 Broadband
VMG4825-B10A User’s Guide
74
6.3 The Advanced Screen
Use the Advanced screen to enable or disable ADSL over PTM, Annex M, DSL PhyR, and SRA
(Seamless Rate Adaptation) functions. The VMG supports the PhyR retransmission scheme. PhyR is
a retransmission scheme designed to provide protection against noise on the DSL line. It improves
voice, video and data transmission resilience by utilizing a retransmission buffer.
ITU-T G.993.2 standard defines a wide range of settings for various parameters, some of which are
encompassed in profiles as shown in the next table.
Click Network Setting > Broadband > Advanced to display the following screen.
Service
Category
Select UBR Without PCR for applications that are non-time sensitive, such as e-mail.
Select CBR (Continuous Bit Rate) to specify fixed (always-on) bandwidth for voice or data
traffic.
Select Non Realtime VBR (non real-time Variable Bit Rate) for connections that do not
require closely controlled delay and delay variation.
Select Realtime VBR (real-time Variable Bit Rate) for applications with bursty connections
that require closely controlled delay and delay variation.
VLAN This section is available only when you select ADSL/VDSL over PTM in the Type field.
Active Select Enable to enable VLAN on this WAN interface.
802.1p IEEE 802.1p defines up to 8 separate traffic types by inserting a tag into a MAC-layer frame
that contains bits to define class of service.
Select the IEEE 802.1p priority level (from 0 to 7) to add to traffic through this connection.
The greater the number, the higher the priority level.
802.1q Type the VLAN ID number (from 0 to 4094) for traffic through this connection.
OK Click OK to save your changes.
Cancel Click Cancel to exit this screen without saving.
Table 10 Network Setting > Broadband > Add New WAN Interface/Edit (ADSL over ATM-Bridge
Mode) (continued)
LABEL DESCRIPTION
Table 11 VDSL Profiles
PROFILE
BANDWIDTH
(MHZ)
NUMBER OF
DOWNSTREAM
CARRIERS
CARRIER
BANDWIDTH
(KHZ)
POWER (DBM)
MAX.
DOWNSTREAM
THROUGHPUT
(MBIT/S)
8a 8.832 2048 4.3125 17.5 50
8b 8.832 2048 4.3125 20.5 50
8c 8.5 1972 4.3125 11.5 50
8d 8.832 2048 4.3125 14.5 50
12a 12 2783 4.3125 14.5 68
12b 12 2783 4.3125 14.5 68
17a 17.664 4096 4.3125 14.5 100
30a 30 3479 8.625 14.5 200