FK1260 0706 A JF-2MED, JF-2HD HANDS-FREE COLOR VIDEO INTERCOM INTERPHONE VIDEO COULEUR MAINS LIBRES JF-2MED JF-2HD Master monitor station Moniteur maître Sub monitor station Moniteur secondaire -1- INSTALLATION & OPERATION MANUAL MANUEL D'INSTALLATION ET D'UTILISATION
PRECAUTIONS Français English General Prohibitions Prohibition to Dismantle the Unit Prohibition on Subjecting the Unit to Water WARNING GENERAL PRECAUTIONS (Negligence could result in death or serious injury.) 1. Keep the unit more than 1 m away from radio or TV set. 2. This unit is for indoor use only. Do not use outdoors. 3. In areas where broadcasting station antennas are close by, the intercom system may be affected by radio frequency interference. 4.
2 INSTALLATION 2-1 Mounting locations 2 The master monitor station and sub 1 Install the master monitor station and 3 Allow 15 cm (6") or more of vertical open space monitor station have switches on both sides. Allow at least 5 cm (2") of open space on either side. from the center of the mounting bracket in order to mount the master monitor station and sub monitor station. 3 JF-2MED / JF-2HD 2 + 5 cm (2") English sub monitor station in places where the screens are not exposed to direct sunlight.
3 WIRING Insert wires securely into each terminal as shown. English DOOR 1 Video door station JF-2MED AIPHO NE JF-DA JF-DA Master monitor station AIPHONE JF-DVF AIPHON E JF-DV JF-DV JF-DVF #2 #1 Français A1 A2 2 Nederlands NP DOOR 2 AIPHO NE JF-DA JF-DA AIPHONE JF-DVF AIPHON E JF-DV JF-DV JF-DVF P JF-D (Audio only) Setting is required.
JF-2HD Sub monitor station Option connector JF-2HD Sub monitor station (BR) (RD) (OG) SW (YE) SW (GR) (BL) PK (PR) FS (GY) (WH) E #3 [5] [6] English #3 [2] #3 To prevent shorts, be sure to cut unused lead wires at the bottom and insulate the ends. Français 4 4 - + ON ON • Terminal setting (2nd unit) Setting changes are only required when a 3rd unit is connected. Put the switch in the ON position, and terminate the furthest sub station.
4 MOUNTING Back wiring Mounting screws x 2 1-gang box English JF-2MED JF-2HD 83,5 mm (3-5/16") Peel off the protective film from the display surfaces of the JF-2MED and JF2HD. Français Mounting bracket 1. Press the RELEASE button (to insert or remove the wire). 2. Insert the cable into the terminal. 1 2 Nederlands 9mm (3/8") Surface wiring PS-1820 * When a 1-gang box is not mounted, the cable can be surface-run to the top or bottom of the unit.
6 OPERATING METHOD Main symbols and function descriptions To operate this unit, check the symbol and then press the appropriate operation button. This is not a touch-panel operation. Symbol Operation guidance display The guidance differs according to the screen. To play Message 1 for entrance. Symbol The symbols differ according to the screen. To play Message 2 for entrance. Operation buttons Press to select a symbol that is displayed on the screen.
7-3 SET THE DATE/TIME JF-2MED 1 After performing steps 1 and 2 in section 7-1, select "SET 3 Press CALL button to set the "Year" and move the cursor to "Month". THE DATE/TIME" and press CALL button. English 2006 01 JAN 00:00 2006 01 JAN 00 : 00 SELECT 2 In the time setting screen, press PLAY button or REC button to 4 Perform the same steps to set the "Month", "Day", "Hour" and "Minute". After setting "Minute", press CALL button to complete the settings.
7-7 SET DOOR2 JF-2MED 2 In the "SET DOOR2" screen, press PLAY button or REC button to When connecting door station 2, set "Video", "Audio" or "None (door station 2 not connected)". These operations must be performed by an installer. Please do not change these settings yourself. select the type of door station that is connected. 1 After performing steps 1 and 2 in section 7-1, select "SET DOOR2" and press CALL button.
8 OPERATIONS 8-1 Answering a door call (HANDS-FREE mode, PTT mode) 1 Press CALL button. English Instant voice call function 2 Even without answering, door area can be seen and heard with video and audio (for approx. 45 seconds). Inside sound is not heard outside. Français 2 Chime tone sounds, caller is seen on video monitor, and outside sound is heard. • Audio and video turns off after approx. 45 seconds in not answered.
8-3 Message for entrance 1 During communication, instant voice call or entrance 3 Press either CALL button or PLAY button. The selected Message changes to yellow, "SENDING MESSAGE" is displayed, and the selected message is played from door station. monitoring, press MENU/MEMO button to display the menu screen. THE TALK BUTTO N TO END. SEND MESSAGE FOR ENTRANCE 2 Press PLAY button. SENDING MESSAGE English PRESS NOTES: Record separate messages in advance for Message 1 and Message 2.
8-6 Transfer entrance call English 1 During communication with door station, press CALL button to call 3 If TALK button is pressed at the transferred station, communication the transferring station. • CALL button (red) flashes and the communication with door station is put on hold. • The "All Call" function is activated to link all the master/sub stations. NOTES: 1.
8-9 Play recorded picture If there are automatically recorded pictures, such as those taken while you were out, the play LED (red) flashes. 1 Press PLAY button in the standby mode to display the play screen. 3/16 PRESS THE TALK BUTTON TO END 2 Press PLAY button on the play screen. The recorded picture is played. When the play of 1 picture ends, the next image is displayed.
8-11 Erase recorded picture English It is also possible to erase saved recorded pictures. The erasure of recorded pictures is performed for each picture in turn. 2 Press REC button. 3/16 2006 02 DEC 18 : 45 1 Display the picture that you want to erase in the play screen. (Refer to section 8-9) Press MENU/MEMO button to display the save/erase selection screen. SAVE/ERASE 3 Press CALL button to erase. 3/16 Press PLAY button to stop the erasure and return to the play screen.
8-14 Erasing Voice memos JF-2MED 1 Press MENU/MEMO button in the standby mode. 3 Press MENU/MEMO button. 02 DEC 18:45 02 DEC 18:47 02 DEC 18:48 2 Select the memo that you want to erase with CALL PLAY REC ERACE 4 Press CALL button to erase. Press PLAY button to stop the English SELECT erasure and return to the Voice memo selection screen. Once a Voice memo is erased, it cannot be restored. button. Each time CALL button is pressed, the cursor switches between A, B, and C.
WARRANTY This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
