Users Guide & Installation Handbook Belling 60 - 70 - 90cm Hob Touch UK Part No 082757203 Date 11.07.
CONTENTS & INTRODUCTION CONTENTS WARRANTY • SAFETY • USING THE PRODUCT • CLEANING • INSTALLATION INSTRUCTIONS • TECHNICAL DATA • CUSTOMER CARE Your new appliance comes with our 12-month guarantee, protecting you against electrical and mechanical breakdown. To register your appliance please call 0844 481 0182, complete the registration form included or register online at the web address located on the back page of this book.
SAFETY WARNING! This appliance and its accessible parts may become hot during use. To avoid burns, children less than 8 years of age shall be kept away unless continuously supervised. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
SAFETY General Fire Safety Advice Servicing should be carried out only by authorised personnel. Most kitchen fires occur when people are distracted or leave things unattended, so remember: Do not spray aerosols in the vicinity of this appliance while it is in operation. Do not store or use flammable liquids or items in the vicinity of this appliance. Do not modify this appliance. • • • • Always ensure that pan bases are dry, stable and flat before using them on the hob.
SAFETY Avoiding damage to the appliance. The ceramic glass of the hob can be damaged by objects falling onto it. Be especially careful with heavy jars of food being stored in cupboards above the hob, we recommend storing them away from the hob area. The edge of the glass can be damaged by being knocked by cookware. Cookware made of cast iron, cast aluminium or with damaged bottoms can scratch the ceramic glass if pushed across the surface.
USING THE HOB - ELECTRIC (CERAMIC) Cooking Surface layout 1 1 COOKING ZONES 2 TOUCH CONTROLS 1 KEYLOCK 2 CENTRAL ON/OFF KEY 3 COOK ZONE KEYS (1 - 4) 4 POWER LEVEL/COOK ZONE DISPLAY 5 POWER LEVEL ADJUST (+ / -) 6 DUAL ZONE KEY (IF FITTED) 7 TIMER KEY 2 Touch Control Layout 7 3 6 TIMER KEY 2 KEY 3 4 DUAL KEY KEY 1 KEY 4 2 1 5 Note; Generic illustrations shown above your appliance may visually differ.
USING THE HOB - ELECTRIC (CERAMIC) Appyling Power To The Hob Switching On (Individual Cook Zone) Before switching on the power supply to the appliance, switch off any bright lights (Such as a cooker hood) and ensure the appliance is not in direct sunlight. 1, Ensure the Key lock is deactivated. This is to enable the electronic controls to calibrate its sensitivity against the natural ambient lighting (Approx 30 seconds).
USING THE HOB - ELECTRIC (CERAMIC) To operate the dual cook zone Auto Heat Up • • Select appropriate cook zone and increase to power level 9 • Whilst the heater display is still flashing press the central dual zone key, a red LED will illuminate next to the cook zone to indicate it has been activated. Now press the up (+) key again and until the Red LED is illuminated next to the cook zone. • The power level of the cook zone will stop flashing and the power level is set.
USING THE HOB - ELECTRIC (CERAMIC) Timer (All Cook Zones) All 4 cooking zones can be operated under the timer independently and at the same time for up to 99 minutes. When the set time expires the timer will beep and the cook zone will switch off automatically. To Set The Timer To A Cook Zone 1, Set the desired power level to the cook zone.
ERROR CODES Hob Status Codes Fault Description Action H Residual Heater No Fault " H" will switch off when o glass surface drops below 60 C Appliance Errors & Alarms Fault Description Action F0 Touch Control Error Switch the power off and on, The system will reset and the hob should now be working correctly FA Touch Control Error Switch the power off and on,The system will reset and the hob should now be working correctly FU Touch Control Error Switch the power off and on, The system will r
CLEANING ELECTRIC HOB • Ceramic glass hobs • It is recommended that you clean and wash the hob surface before using for the first time. Apply a thin coat of ceramic hob cleaner to the hob to help maintain and protect it. • The ceramic hob top can be cleaned using a clean, damp cloth or kitchen paper. Do not use a used dishcloth or sponge as they can leave a film of detergent on the surface which can lead to discoloration. Please ensure that the elements are cooled fully to avoid steam burns.
INSTALLATION General information Installation should only be carried out by a qualified installer or engineer. between hob base and appliance must be maintained. Installation above an oven Please keep to the following points most carefully; Refer to the manufacturer’s instructions for clearances above the oven. Although every care has been taken to ensure this appliance has no burrs, or sharp edges, we recommend that you wear protective gloves when installing and moving this appliance.
INSTALLATION Clearances and dimension – requirements No shelf or overhang of combustible material should be closer than 650mm above the hob. There must be a minimum clearance of 50mm between the edges of the hob and any side walls; this clearance must be maintained up to 420mm above the worktop. * 650mm min There must be a minimum clearance of 50mm between the rear edge of the hob and the rear wall. This clearance must be maintained up to 650mm above the worktop.
INSTALLATION Fitting into worktop Recessed Method Cut a hole in the work surface to the required size. The worktop must be of heat-resistant material or covered with heat-resistant material. Recess the work top to the appropriate depth (Approx 5mm) and shape to fit the hob (add 1mm to overall glass size). Refer to the installation bracket advice to determine your installation type. Insert the hob into the recess, ensuring that the foam seal is sitting correctly.
INSTALLATION Installation Bracket Advice Installation pack 2 Secure the hob to the worktop by means of the brackets provided, taking the thickness of the worktop into account. 4 x Cranked installation bracket 4 x Spire clips (70/90cm appliances only) 4 x No8 Screws UNDERSIDE OF HOB Depending on your appliance the cranked bracket may or may not require the spire clips detailed in pack 1.
INSTALLATION CONNECT TO THE ELECTRICITY SUPPLY WARNING: This appliance must be earthed. Only connect to the electrical mains terminal with the power switched off. The electrical mains terminal is live. Follow the terminal block connection schematic • Remove the cable clamp screw and release the cable clamp retaining arm. Note; The cable clamp has a ratchet type mechanism on the right hand side of the retaining arm. • Loose and inappropriate connections can make the terminal overheat.
TECHNICAL DATA SUPPLY: 220 -240V ~ 50Hz 5.04kW - 6.
CUSTOMER CARE CUSTOMER CARE WEB SHOP Having purchased a superior cooker, hob or hood from us, you’ll naturally want to keep it looking great. And who better to help you care for it than the manufacturer? We offer an extensive range of accessories, components and cleaning products which, will instantly give your cooker a good as new look. range of Bake ware and Cookware essentials including Roasting Pans, Cake Tins and Non-Stick Cooking Liners. For all enquires, please visit our Web Shop at www.gdhaonline.
Please keep this handbook for future reference, or for anyone else who may use the appliance.
CUSTOMER CARE To contact Belling about your appliance, please call Warranty Registration 0844 481 0182 to register your appliance Customer Care Helpline 0844 815 3746 in case of difficulty within the UK Alternatively general, spares and service information is available from our website at www.belling.co.uk Please ensure that you have the product’s model no and serial no available when you call.
