Operation Guide

Operation Guide 5562
E-29
3. When the timekeeping setting you want to change is flashing, use D and/or B
to change it as described below.
Screen To do this: Do this:
Toggle between 12-hour (12H) and 24-hour
(24H) timekeeping
Press D.
Reset the seconds to 00
Change the hour or minute
Use D (+) and B (–).
Change the year, month, or day
E-28
2. Press C to move the flashing in the sequence shown below to select the other
settings.
City Code
(page E-24)
C
DST
(page E-26)
C
12/24-Hour Format
C
Seconds
C
C
Power Saving
(page E-59)
Hour
C
C
Illumination Duration
(page E-46)
Minute
C C
Button Operation Tone On/Off
(page E-57)
C
Day
C
Month
C
Year
x The following steps explain how to configure timekeeping settings only.
E-27
Configuring Current Time and Date Settings
You can configure current time and date settings.
To change the current time and date settings
1. In the Timekeeping Mode, hold down A for about two
seconds until ADJ is displayed.
When you release A, the city code and city name will
scroll from right to left. This is the setting screen.
x The hour and minute hands will automatically move
out of the way at this time (page E-54).
City code
E-26
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A for about two
seconds until ADJ is displayed.
When you release A, the city code and city name will
scroll from right to left. This is the setting screen.
x The hour and minute hands will automatically move
out of the way at this time (page E-54).
2. Press C to enter the DST setting screen.
3. Press D to toggle the DST setting between Daylight
Saving Time (ON) and Standard Time (OFF).
x Note that you cannot switch between standard time
and daylight saving time (DST) while UTC is selected
as your Home City.
4. After the setting is the way you want, press A to return to the Timekeeping
Mode.
x The DST indicator appears to indicate that Daylight Saving Time is turned on.
DST indicator
E-25
3. After the setting is the way you want, press A to return to the Timekeeping
Mode.
Note
x After you specify a city code, the watch will use UTC* offsets in the World Time
Mode to calculate the current time for other time zones based on the current time
in your Home City.
* Coordinated Universal Time, the world-wide scientific standard of timekeeping.
The reference point for UTC is Greenwich, England.
E-24
Configuring Home City Settings
There are two Home City settings: actually selecting the Home City, and selecting
either standard time or daylight saving time (DST).
To configure Home City settings
1. In the Timekeeping Mode, hold down A for about two
seconds until ADJ is displayed.
When you release A, the city code and city name will
scroll from right to left. This is the setting screen.
x For details about city codes, see the “City Code
Table” at the back of this manual.
x The hour and minute hands will automatically move
out of the way at this time (page E-54).
2. Use D (East) and B (West) to scroll through the city codes until the one you
want to use as your Home City is displayed.
City code
E-23
Timekeeping
Use the Timekeeping Mode to set and view the current
time and date.
x Each press of A cycles the Home City information as
shown below.
Month, Day,
Day of the week
Month, Day,
Seconds
Hour : Minutes,
Seconds
A A
PM indicator
A
Hour
Minutes
Day of the week
Month Day
E-22
General Functions (All Modes)
The functions and operations described in this section can be used in all of the
modes.
Auto Return
x The watch returns to the Timekeeping Mode automatically if you do not perform
any button operation for two or three minutes in the Alarm Mode.
x If you leave the watch with a setting screen (flashing digits) displayed for two or
three minutes without performing any operation, the watch will exit the setting
screen automatically.
Initial Screens
When you enter the World Time or Alarm Mode, the data you were viewing when
you last exited the mode appears first.
Scrolling
The B and D buttons are used in the setting screen to scroll through data. In
most cases, holding down these buttons during a scroll operation scrolls through
the data at high speed.
E-21
Countdown Timer Mode
C
Alarm Mode Stopwatch Mode
C
C
E-20
Selecting a Mode
x The illustration below shows which buttons you need to press to navigate between
modes.
x To return to the Timekeeping Mode from any other mode, hold down C for at
least four seconds.
Timekeeping Mode
World Time Mode
C C