Notebook User Guide
© Copyright 2012 Hewlett-Packard Development Company, L.P. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. Intel and Centrino are trademarks of Intel Corporation in the U.S. and other countries. AMD is a trademark of Advanced Micro Devices, Inc. SD Logo is a trademark of its proprietor. Inc. Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. The information contained herein is subject to change without notice.
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
iv Safety warning notice
Table of contents 1 Welcome .......................................................................................................................................................... 1 Finding information ............................................................................................................................... 2 2 Getting to know your computer ..................................................................................................................... 4 Top ....................
4 Pointing devices and keyboard ................................................................................................................... 28 Using pointing devices ....................................................................................................................... 28 Setting pointing device preferences ................................................................................... 28 Using the TouchPad .........................................................................
Using the power meter and power settings ....................................................................... 43 Using battery power ........................................................................................................................... 44 Finding additional battery information ................................................................................ 44 Using Battery Check ..........................................................................................................
Replacing or upgrading the hard drive ............................................................................... 59 Removing the hard drive ................................................................................... 59 Installing a hard drive ........................................................................................ 61 Improving hard drive performance ..................................................................................... 63 Using Disk Defragmenter ..................
Locating the fingerprint reader ........................................................................................... 81 10 Maintenance ................................................................................................................................................ 82 Adding or replacing memory modules ................................................................................................ 82 Cleaning your computer ................................................................
Appendix B Troubleshooting ........................................................................................................................ 105 Troubleshooting resources ............................................................................................................... 105 Resolving issues .............................................................................................................................. 105 The computer is unable to start up ...................................
1 Welcome After you set up and register the computer, it is important to take the following steps: ● Connect to the Internet—Set up your wired or wireless network so that you can connect to the Internet. For more information, see Connecting to a network on page 22. ● Update your antivirus software—Protect your computer from damage caused by viruses. The software is preinstalled on the computer. For more information, see Using antivirus software on page 79.
Finding information The computer comes with several resources to help you perform various tasks. Resources For information about Setup Instructions poster ● How to set up the computer ● Help to identify computer components Windows 8 Basics guide Overview of using and navigating with Windows® 8. Help and Support ● Operating system information To access Help and Support, from the Start screen, type help, and then select Help and Support. For U.S. support, go to http://www.hp.com/go/contactHP.
Resources For information about Limited Warranty* Warranty information To access this guide, select the HP Support Assistant app, select My computer, and then select User guides, or go to http://www.hp.com/go/ orderdocuments. *You can find the expressly provided HP Limited Warranty applicable to your product located with the user guides on your computer and/or on the CD/DVD provided in the box. In some countries/regions, HP may provide a printed HP Limited Warranty in the box.
2 Getting to know your computer Top TouchPad Component 4 Description (1) TouchPad on/off button Turns the TouchPad on and off. (2) TouchPad zone Moves the pointer and selects or activates items on the screen. (3) Left TouchPad button Functions like the left button on an external mouse. (4) Right TouchPad button Functions like the right button on an external mouse.
Lights NOTE: Refer to the illustration that most closely matches your computer. Component (1) Description Power light ● On: The computer is on. ● Blinking: The computer is in the Sleep state. ● Off: The computer is off or in Hibernation. Hibernation is an energy-saving mode that uses the least amount of power. (2) Caps lock light On: Caps lock is on. (3) Web browser light ● On: The computer is on. ● Off: The computer is off.
Components (1) Power light ● On: The computer is on. ● Blinking: The computer is in the Sleep state. ● Off: The computer is off or in Hibernation. Hibernation is an energy-saving mode that uses the least amount of power. (2) Caps lock light On: Caps lock is on. (3) Web browser light ● On: The computer is on. ● Off: The computer is off.
Buttons, speakers, and fingerprint reader (select models only) NOTE: Refer to the illustration that most closely matches your computer. Component (1) Description Power button ● When the computer is off, press the button to turn on the computer. ● When the computer is on, press the button briefly to initiate Sleep. ● When the computer is in the Sleep state, press the button briefly to exit Sleep. ● When the computer is in Hibernation, press the button briefly to exit Hibernation.
Component 8 Description (3) Web browser button Opens the default Web browser. (4) Wireless button Turns the wireless feature on or off but does not establish a wireless connection. (5) Fingerprint reader (select models only) Allows a fingerprint logon to Windows, instead of a password logon.
Component (1) Description Power button ● When the computer is off, press the button to turn on the computer. ● When the computer is on, press the button briefly to initiate Sleep. ● When the computer is in the Sleep state, press the button briefly to exit Sleep. ● When the computer is in Hibernation, press the button briefly to exit Hibernation.
Keys NOTE: Refer to the illustration that most closely matches your computer. Component Description (1) esc key Displays system information when pressed in combination with the fn key. (2) fn key Executes frequently used system functions when pressed in combination with a function key, the num lk key, the esc key, or other keys. For more information, see Pointing devices and keyboard on page 28. (3) Windows logo key Displays the Windows Start screen.
Component Description (1) esc key Displays system information when pressed in combination with the fn key. (2) fn key Executes frequently used system functions when pressed in combination with a function key, the num lk key, the esc key, or other keys. For more information, see Pointing devices and keyboard on page 28. (3) Windows logo key Displays the Windows Start screen. (4) Function keys Execute frequently used system functions when pressed in combination with the fn key.
Front Component (1) (2) (3) Description Hard drive light Media Card Reader Audio-out (headphone) jack ● Blinking white: The hard drive is being accessed. ● Amber: HP 3D DriveGuard has temporarily parked the hard drive.
Right NOTE: Refer to the illustration that most closely matches your computer. Component Description (1) USB 3.0 port Connects an optional USB device. (2) USB 2.0 port Connects an optional USB device. (3) Optical drive (select models only) Reads and writes (select models only) to an optical disc. (4) Optical drive light (select models only) ● On: The optical drive is being accessed. ● Off: The optical drive is idle.
Component (1) USB 2.0 ports (2) Connect optional USB devices. (2) Optical drive (select models only) Reads and writes (select models only) to an optical disc. (3) Optical drive light (select models only) ● On: The optical drive is being accessed. ● Off: The optical drive is idle. (4) 14 Description Optical drive eject button (select models only) Chapter 2 Getting to know your computer Releases the optical drive disc tray.
Left NOTE: Refer to the illustration that most closely matches your computer. Component (1) Description Security cable slot Attaches an optional security cable to the computer. NOTE: The security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen. (2) Vent Enables airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating.
Component (1) Description Security cable slot Attaches an optional security cable to the computer. NOTE: The security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen. (2) Power connector Connects an AC adapter. (3) AC adapter/battery light ● Amber: The computer is connected to external power and the battery is charged from 0 to 90 percent.
Display NOTE: Refer to the illustration that most closely matches your computer. Component Description (1) WLAN antennas (2)* Send and receive wireless signals to communicate with wireless local area networks (WLAN). (2) WWAN antennas (2)* (select models only) Send and receive wireless signals to communicate with wireless wide-area networks (WWAN). (3) Internal microphone(s) (1 or 2 depending on model) Record sound. (4) Webcam light On: The webcam is in use.
Component Description (1) WLAN antennas (2)* Send and receive wireless signals to communicate with wireless local area networks (WLAN). (2) WWAN antennas (2)* (select models only) Send and receive wireless signals to communicate with wireless wide-area networks (WWAN). (3) Internal microphone(s) (1 or 2 depending on model) Record sound. (4) Webcam light (select models only) On: The webcam is in use. (5) Webcam (select models only) Records video and captures still photographs.
Bottom Component (1) Description Battery and service door release latches ● Releases the battery from the battery bay by sliding the release latches one time. ● When the battery has been removed from the battery bay, releases the service door from the computer by sliding the release latches a second time. (2) Battery bay Holds the battery. (3) Service door Protects the hard drive bay, the wireless LAN (WLAN) module slot, the WWAN module slot, and the memory module slots.
Identifying the bottom parts of the computer NOTE: Refer to the illustration that most closely matches your computer. The service door has been removed in the following illustrations.
Components Description (3) SIM module (select models only) (4) WWAN module (select models only) (5) WLAN module (select models only) Identifying the bottom parts of the computer 21
3 Connecting to a network Your computer can travel with you wherever you go. But even at home, you can explore the globe and access information from millions of websites using your computer and a wired or wireless network connection. This chapter will help you get connected to that world. Connecting to a wireless network Wireless technology transfers data across radio waves instead of wires.
Because the wireless devices are enabled at the factory, you can use the wireless button to turn on or turn off the wireless devices simultaneously. Using operating system controls The Network and Sharing Center allows you to set up a connection or network, connect to a network, manage wireless networks, and diagnose and repair network problems. To use operating system controls: 1. From the Start screen, type n, and then select Settings.. 2.
Setting up a WLAN To set up a WLAN and connect to the Internet, you need the following equipment: ● A broadband modem (either DSL or cable) (1) and high-speed Internet service purchased from an Internet service provider ● A wireless router (2) (purchased separately) ● A wireless computer (3) NOTE: Some modems have a built-in wireless router. Check with your ISP to determine what type of modem you have.
Wireless encryption uses security settings to encrypt and decrypt data that is transmitted over the network. For more information, from the Start screen, type help, and then select Help and Support. Connecting to a WLAN To connect to the WLAN, follow these steps: 1. Be sure that the WLAN device is on. If the device is on, the wireless light is on. If the wireless light is off, press the wireless button. NOTE: On some models, the wireless light is amber when all wireless devices are off. 2.
Using Bluetooth wireless devices A Bluetooth device provides short-range wireless communications that replace the physical cable connections that traditionally link electronic devices such as the following: ● Computers (desktop, notebook, PDA) ● Phones (cellular, cordless, smart phone) ● Imaging devices (printer, camera) ● Audio devices (headset, speakers) ● Mouse Bluetooth devices provide peer-to-peer capability that allows you to set up a personal area network (PAN) of Bluetooth devices.
Connecting to a wired network There are 2 kinds of wired connections: local area network (LAN) and modem connection. A LAN connection uses a network cable and is much faster than a modem, which uses a telephone cable. Both cables are sold separately. WARNING! To reduce the risk of electric shock, fire, or damage to the equipment, do not plug a modem cable or telephone cable into an RJ-45 (network) jack.
4 Pointing devices and keyboard Using pointing devices NOTE: In addition to the pointing devices included with your computer, you can use an external USB mouse (purchased separately) by connecting it to one of the USB ports on the computer. Setting pointing device preferences Use Mouse Properties in Windows to customize settings for pointing devices, such as button configuration, click speed, and pointer options.
Turning the TouchPad off and on To turn the TouchPad off and on, quickly double-tap the TouchPad on/off button. The following table shows and describes the TouchPad display icons. TouchPad light Icon Description Amber Indicates that the TouchPad is off. Off Indicates that the TouchPad is on. Navigating To move the pointer, slide one finger across the TouchPad in the direction you want the pointer to go.
TIP: For touch screen computers, you may perform the gestures on the display, on the TouchPad or a combination of the two. The TouchPad supports a variety of gestures. To use TouchPad gestures, place two fingers on the TouchPad at the same time. NOTE: TouchPad gestures are not supported in all programs. 1. From the Start screen type, mouse, click Settings, and then select Mouse from the list of applications. 2.
Scrolling Scrolling is useful for moving up, down, or sideways on a page or image. To scroll, place two fingers slightly apart on the TouchPad or touch screen (select models only), and then drag them across the TouchPad or touchscreen in an up, down, left, or right motion. NOTE: Scrolling speed is controlled by finger speed. Pinching/Zooming Pinching and zooming allows you to zoom out or in on images or text. ● Zoom out by placing two fingers apart and then moving your fingers together.
Using the keyboard Identifying the hot keys A hot key is a combination of the fn key and either the esc key or one of the function keys. To use a hot key: ▲ Briefly press the fn key, and then briefly press the second key of the hot key combination. Hot key combination Description fn+esc Displays information about system hardware components and the system BIOS version number. fn+f1 Initiates Sleep, which saves your information in system memory.
Hot key combination Description fn+f11 Plays, pauses, or resumes an audio CD, a DVD, or a BD. fn+f12 Plays the next track of an audio CD or the next section of a DVD or a BD. Using keypads The computer includes either an embedded numeric keypad or an integrated numeric keypad. The computer also supports an optional external numeric keypad or an optional external keyboard that includes a numeric keypad.
Turning the embedded numeric keypad on and off Press fn+num lk to turn on the embedded numeric keypad. Press fn+num lk again to turn off the keypad. NOTE: The embedded numeric keypad is turned off while an external keyboard or numeric keypad is connected to the computer.
Using an optional external numeric keypad Keys on most external numeric keypads function differently according to whether num lock is on or off. (Num lock is turned off at the factory.)For example: ● When num lock is on, most keypad keys type numbers. ● When num lock is off, most keypad keys function like the arrow, page up, or page down keys. When num lk on an external keypad is turned on, the num lock light on the computer is turned on.
5 Multimedia Your computer may include the following: ● Integrated speaker(s) ● Integrated microphone(s) ● Integrated webcam ● Preinstalled multimedia software ● Multimedia buttons or keys Using the media activity controls Depending on your computer model, you may have the following media activity controls that allow you to play, pause, fast forward, or rewind a media file: ● Media buttons ● Media hotkeys (specific keys pressed in combination with the fn key) ● Media keys Audio Your comput
Adjusting the volume Depending on your computer model, you can adjust the volume using the following: ● Volume buttons ● Volume hotkeys (specific keys pressed in combination with the fn key) ● Volume keys WARNING! To reduce the risk of personal injury, adjust the volume before putting on headphones, earbuds, or a headset. For additional safety information, see the Regulatory, Safety and Environmental Notices.
Webcam (select models only) Some computers include an integrated webcam. With the preinstalled software, you can use the webcam to take a photo or record a video. You can preview and save the photo or video recording.
HDMI (select models only) The HDMI port connects the computer to an optional video or audio device, such as a high-definition television, or to any compatible digital or audio component. NOTE: To transmit video and/or audio signals through the HDMI port, you need an HDMI cable (purchased separately). One HDMI device can be connected to the HDMI port on the computer. The information displayed on the computer screen can be simultaneously displayed on the HDMI device.
Intel Wireless Display (select models only) Intel® Wireless Display allows you to share your computer content wirelessly on your TV. To experience wireless display, a wireless TV adapter (purchased separately) is required. DVDs that have output protection may not play on Intel Wireless Display. (However, DVDs that do not have output protect will play.) Blu-ray discs, which have output protection, will not play on Intel Wireless Display.
6 Power management NOTE: A computer may have a power button or a power switch. The term power button is used throughout this guide to see both types of power controls. Shutting down the computer CAUTION: Unsaved information is lost when the computer shuts down. The shutdown command closes all open programs, including the operating system, and then turns off the display and computer.
Setting power options Using power-saving states Sleep is enabled at the factory. When Sleep is initiated, the power lights blink and the screen clears. Your work is saved to memory. CAUTION: To reduce the risk of possible audio and video degradation, loss of audio or video playback functionality, or loss of information, do not initiate sleep while reading from or writing to a disc or an external media card.
To exit Hibernation, briefly press the power button. The power lights turn on and your work returns to the screen where you stopped working. NOTE: If you have set a password to be required on wakeup, you must enter your Windows password before your work will return to the screen. Setting password protection on wakeup To set the computer to prompt for a password when the computer exits Sleep or Hibernation, follow these steps: 1. From the Start screen, type control, and then select Control Panel. 2.
Using battery power WARNING! To reduce potential safety issues, use only the battery provided with the computer, a replacement battery provided by HP, or a compatible battery purchased from HP. The computer runs on battery power whenever it is not plugged into external AC power. Computer battery life varies, depending on power management settings, running programs, display brightness, external devices connected to the computer, and other factors.
Using Battery Check Help and Support provides information on the status of the battery installed in the computer. To run Battery Check: 1. Connect the AC adapter to the computer. NOTE: The computer must be connected to external power for Battery Check to work properly. 2. From the Start screen, type control, and then select Control Panel from the list of applications. Click Hardware and Sound, and then click Power Options. 3. Click the Power tab, and then click Battery Check.
NOTE: For additional information about the power meter, see Using the power meter on page 43. If the computer is on or in the Sleep state, the computer remains briefly in the Sleep state, and then shuts down and loses any unsaved information.
Removing a battery To remove the battery: CAUTION: Removing a battery that is the sole power source for the computer can cause loss of information. To prevent loss of information, save your work and shut down the computer through Windows before removing the battery. 1. Turn the computer upside down on a flat surface, with the battery bay toward you. 2. Slide the battery release latches (1) to release the battery. NOTE: You can slide the battery release latches simultaneously or one at a time. 3.
Storing a user-replaceable battery (select models only) CAUTION: To reduce the risk of damage to a battery, do not expose it to high temperatures for extended periods of time. If a computer will be unused and unplugged from external power for more than 2 weeks, remove the user-replaceable battery and store it separately. To prolong the charge of a stored battery, place it in a cool, dry place. NOTE: A stored battery should be checked every 6 months.
When you connect the computer to external AC power, the following events occur: ● The battery begins to charge. ● If the computer is turned on, the power meter icon in the notification area changes appearance. When you disconnect external AC power, the following events occur: ● The computer switches to battery power. ● The display brightness is automatically decreased to save battery life.
Switchable graphics/dual graphics (select models only) Select computers are equipped with either switchable graphics or dual graphics. ● Switchable graphics—Supported by both AMD™ and Intel. If your computer has AMD dynamic switchable graphics, it supports only switchable graphics. ● Dual graphics—Supported only by AMD. If your computer has AMD Radeon dual graphics, it supports only dual graphics. NOTE: Dual graphics can be enabled only by full-screen applications that use DirectX version 10 or 11.
Using dual graphics (select models only) If your system is equipped with dual graphics (two or more added Graphics Processing Units (GPUs)), you can enable AMD Radeon Dual Graphics to increase application power and performance for full-screen applications that use DirectX version 10 or 11. For more information about DirectX, see http://www.microsoft.com/directx.
7 External cards and devices Using Media Card Reader cards (select models only) Optional digital cards provide secure data storage and convenient data sharing. These cards are often used with digital media–equipped cameras and PDAs as well as with other computers. To determine the digital card formats that are supported on your computer, see the Getting to know your computer on page 4 section.
Removing a digital card CAUTION: To reduce the risk of loss of data or an unresponsive system, use the following procedure to safely remove the digital card. 1. Save your information and close all programs associated with the digital card. 2. Click the remove hardware icon in the notification area, at the far right of the taskbar. Then follow the on-screen instructions. 3. Press in on the card (1), and then remove it from the slot (2). NOTE: If the card does not eject, pull the card out of the slot.
Connecting a USB device CAUTION: To reduce the risk of damage to a USB connector, use minimal force to connect the device. ▲ Connect the USB cable for the device to the USB port. NOTE: The following illustration may look slightly different than your computer. You will hear a sound when the device has been detected. NOTE: The first time you connect a USB device, a message in the notification area lets you know that the device is recognized by the computer.
Using optional external devices NOTE: For more information about required software and drivers, or to learn which computer port to use, see the manufacturer's instructions. To connect an external device to the computer: CAUTION: To reduce the risk of damage to the equipment when connecting a powered device, be sure that the device is turned off and the AC power cord is unplugged. 1. Connect the device to the computer. 2.
8 Drives Handling drives CAUTION: Drives are fragile computer components that must be handled with care. Refer to the following cautions before handling drives. Additional cautions are included with the procedures to which they apply. Observe these precautions: 56 ● Before you move a computer that is connected to an external hard drive, initiate Sleep and allow the screen to clear, or properly disconnect the external hard drive.
Using hard drives CAUTION: To prevent information loss or an unresponsive system: Save your work and shut down the computer before adding or replacing a memory module or hard drive. If you are not sure whether the computer is off, turn the computer on by pressing the power button. Then shut down the computer through the operating system. Using the optional security screw Use the optional security screw to lock the service door to the bottom of the computer.
Removing or replacing the service door Removing the service door Remove the service door to access the memory module slot, hard drive, regulatory label, and other components. 1. Remove the battery (see Inserting or removing the battery on page 46). 2. With the battery bay toward you, remove the security screw (1) (if the optional screw is being used), and then slide the release latches (2) to release the service door. NOTE: If you want to use the optional screw, you can store it inside the service door.
2. Replace the security screw (4), if desired. For additional information about the security screw, see Using the optional security screw on page 57. NOTE: If you want to use the optional screw, it is stored inside the service door. 3. Insert the battery (see Inserting or removing the battery on page 46). Replacing or upgrading the hard drive CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before removing the hard drive from the hard drive bay.
6. Pull the plastic tab on the hard drive (2) towards the side of the computer to disengage the hard drive from the connector, and then lift the hard drive out of the hard drive bay. NOTE: Refer to the illustration that most closely matches your computer. Some hard drives may be wrapped in a plastic covering. After removing the hard drive from the computer, you must remove the plastic covering to access the hard drive itself.
Installing a hard drive 1. Insert the hard drive into the hard drive bay. 2. Pull the plastic tab on the hard drive (1) towards the center of the computer to engage the hard drive with the connector.
3. Replace the four hard drive screws (2). NOTE: Refer to the illustration that most closely matches your computer. 4. 62 Replace the service door (see Removing or replacing the service door on page 58).
5. Replace the security screw, if desired. For additional information about the security screw, see Using the optional security screw on page 57. 6. Replace the battery (see Inserting or removing the battery on page 46). 7. Turn the computer right-side up, and then reconnect AC power and external devices to the computer. 8. Turn on the computer. Improving hard drive performance Using Disk Defragmenter As you use the computer, files on the hard drive become fragmented.
Using HP 3D DriveGuard (select models only) HP 3D DriveGuard protects the hard drive by parking the drive and halting data requests under either of the following conditions: ● You drop the computer. ● You move the computer with the display closed while the computer is running on battery power. A short time after the end of one of these events, HP 3D DriveGuard returns the hard drive to normal operation. NOTE: Because solid-state drives (SSD) lack moving parts, HP 3D DriveGuard is unnecessary.
Using HP 3D DriveGuard software The HP 3D DriveGuard software enables you to perform the following tasks: ● Enable and disable HP 3D DriveGuard. NOTE: Depending on your user privileges, you may be unable to enable or disable HP 3D DriveGuard. Privileges for non-administrator users can be changed by members of an administrator group. ● Determine whether a drive in the system is supported. To open the software and change settings, follow these steps: 1.
5. Gently press the disc (3) down onto the tray spindle until the disc snaps into place. 6. Close the disc tray. NOTE: After you insert a disc, a short pause is normal. If you have not selected a media player, an AutoPlay dialog box opens. It prompts you to select how you want to use the media content.
Removing an optical disc Tray-load There are 2 ways to remove a disc, depending on whether the disc tray opens normally or not. When the disc tray opens normally 1. Press the release button (1) on the drive bezel to release the disc tray, and then gently pull out the tray (2) until it stops. 2. Remove the disc (3) from the tray by gently pressing down on the spindle while lifting the outer edges of the disc. Hold the disc by the edges and avoid touching the flat surfaces.
When the disc tray fails to open normally 1. Insert the end of a paper clip (1) into the release access in the front bezel of the drive. 2. Press in gently on the paper clip until the tray is released, and then pull out the tray (2) until it stops. 3. Remove the disc (3) from the tray by gently pressing down on the spindle while lifting the outer edges of the disc. Hold the disc by the edges and avoid touching the flat surfaces.
Sharing optical drives Although your computer may not have an integrated optical drive, you can access software and data, and install applications, by sharing an optical drive connected to another computer in your network. Sharing drives is a feature of the Windows operating system that allows a drive on one computer to be accessible to other computers on the same network.
9 Security Protecting the computer Standard security features provided by the Windows operating system and the non-Windows Computer Setup utility (BIOS) can protect your personal settings and data from a variety of risks. NOTE: Security solutions are designed to act as deterrents. These deterrents may not prevent a product from being mishandled or stolen. NOTE: Before you send your computer for service, back up and delete confidential files, and remove all password settings.
Computer risk Security feature Unauthorized removal of the computer Security cable slot (used with an optional security cable) *Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system is not working or will not load. You can use either a pointing device (TouchPad, pointing stick, or USB mouse) or the keyboard to navigate and make selections in Computer Setup.
Setting passwords in Windows Password Function Administrator password* Protects access to a Windows administrator-level account. NOTE: This password cannot be used to access Computer Setup contents. User password* Protects access to a Windows user account. *For information about setting a Windows administrator password or a Windows user password” from the Start screen, type help, and then select Help and Support.
Setting passwords in Computer Setup Password Function BIOS administrator password* Protects access to Computer Setup. DriveLock master password* Protects access to the internal hard drive that is protected by DriveLock. It is also used to remove DriveLock protection. This password is set under DriveLock Passwords during the enable process. DriveLock user password* Protects access to the internal hard drive that is protected by DriveLock, and is set under DriveLock Passwords during the enable process.
Managing a BIOS administrator password To set, change, or delete this password, follow these steps: Setting a new BIOS administrator password 1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f10 to enter Computer Setup. 3. Use a pointing device or the arrow keys to select Security > Setup BIOS Administrator Password, and then press enter. 4. When prompted, type a password. 5.
5. When prompted for the new password, leave the field empty, and then press enter. 6. Read the warning. To continue, select YES. 7. When prompted to type your new password again, leave the field empty, and then press enter. 8. To save your changes and exit Computer Setup, click the Save icon in the lower-left corner of the screen, and then follow the on-screen instructions. – or – Use the arrow keys to select File > Save Changes and Exit, and then press enter.
Setting a DriveLock password To set a DriveLock password in Computer Setup, follow these steps: 1. Turn on the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f10 to enter Computer Setup. 3. Use a pointing device or the arrow keys to select Security > DriveLock, and then press enter. 4. Click Set DriveLock Password (global). 5.
Entering a DriveLock password Be sure that the hard drive is inserted into the computer (not into an optional docking device or external MultiBay). At the DriveLock Password prompt, type your user or master password (using the same kind of keys you used to set the password), and then press enter. After 2 incorrect attempts to enter the password, you must shut down the computer and try again. Changing a DriveLock password To change a DriveLock password in Computer Setup, follow these steps: 1.
7. Type your master password, and then press enter. 8. To save your changes and exit Computer Setup, click the Save icon and then follow the onscreen instructions. – or – Use the arrow keys to select File > Save Changes and Exit, and then press enter. Your changes go into effect when the computer restarts. Using Computer Setup Automatic DriveLock In a multiple-user environment, you can set an Automatic DriveLock password.
5. Use a pointing device or the arrow keys to select Disable protection. 6. To save your changes and exit Computer Setup, click the Save icon in the lower-left corner of the screen, and then follow the on-screen instructions. – or – Use the arrow keys to select File > Save Changes and Exit, and then press enter. Using antivirus software When you use the computer to access e-mail, a network, or the Internet, you potentially expose it to computer viruses.
Installing critical security updates CAUTION: Microsoft® sends out alerts regarding critical updates. To protect the computer from security breaches and computer viruses, install all critical updates from Microsoft as soon as you receive an alert. Updates to the operating system and other software may have become available after the computer left the factory.
Using the fingerprint reader (select models only) Integrated fingerprint readers are available on select computer models. In order to use the fingerprint reader, you must set up a user account with a password on the computer. This account allows you to log on to your computer with a swipe of a designated finger. You may also use the fingerprint reader to fill in password fields on websites and other programs that require a logon. Refer to the fingerprint software Help for instructions.
10 Maintenance Adding or replacing memory modules The computer has one memory module compartment. The capacity of the computer can be upgraded by adding a memory module to the vacant expansion memory module slot or by upgrading the existing memory module in the primary memory module slot. WARNING! To reduce the risk of electric shock and damage to the equipment, unplug the power cord and remove all batteries before installing a memory module.
b. Grasp the edge of the memory module (2), and then gently pull the memory module out of the memory module slot. CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module. To protect a memory module after removal, place it in an electrostatic-safe container. 6. Insert a new memory module: CAUTION: To prevent damage to the memory module, hold the memory module by the edges only.
c. Gently press the memory module (3) down, applying pressure to both the left and right edges of the memory module, until the retention clips snap into place. CAUTION: To prevent damage to the memory module, be sure that you do not bend the memory module. 7. Replace the service door (see Removing or replacing the service door on page 58). 8. Insert the battery (see Inserting or removing the battery on page 46). 9. Connect AC power and external devices to the computer. 10. Turn on the computer.
● Dry microfiber cleaning cloth or a chamois (static-free cloth without oil) ● Static-free cloth wipes CAUTION: Avoid the following cleaning products: Strong solvents, such as alcohol, acetone, ammonium chloride, methylene chloride, and hydrocarbons, which can permanently damage the surface of the computer. Fibrous materials, such as paper towels, which can scratch the computer. Over time, dirt particles and cleaning agents can get trapped in the scratches.
Updating programs and drivers Download the latest versions of HP programs and drivers and also register to receive automatic update notifications when new versions become available. For U.S. support, go to http://www.hp.com/ go/contactHP. For worldwide support, go to http://welcome.hp.com/country/us/en/wwcontact_us.html.
Using SoftPaq Download Manager HP SoftPaq Download Manager (SDM) is a tool that provides quick access to SoftPaq information for HP business computers without requiring the SoftPaq number. Using this tool, you can easily search for SoftPaqs, and then download and unpack them. SoftPaq Download Manager works by reading and downloading, from the HP FTP site, a published database file containing computer model and SoftPaq information.
11 Backup and recovery To protect your information, use Windows Backup and Restore to back up individual files and folders, back up your entire hard drive, create system repair media, or create system restore points. In case of system failure, you can use the backup files to restore the contents of your computer. From the Start screen, type restore, click Settings, and then select from the list of displayed options.
Backing up your information Recovery after a system failure is as good as your most recent backup. You should create system repair media and your initial backup immediately after initial system setup. As you add new software and data files, you should continue to back up your system on a regular basis to maintain a reasonably current backup. The system repair media is used to start up (boot) the computer and repair the operating system in case of system instability or failure.
Using the Windows recovery tools To recover information you previously backed up: ▲ From the Start screen, type help, and then select Help and Support. To recover your information using Startup Repair, follow these steps: CAUTION: Using Startup Repair will completely erase and reformat the hard drive. For additional information, go to Help and Support. From the Start screen, type help, and then select Help and Support. 1. If possible, back up all personal files. 2.
To recover the original hard drive image using f11: 1. If possible, back up all personal files. 2. If possible, check for the presence of the HP Recovery partition: From the Start screen, type computer, and then select Computer. NOTE: If the HP Recovery partition is not listed, you must recover your operating system and programs using the Windows 8 operating system media, and the Driver Recovery media (both purchased separately).
Using HP Software Setup HP Software Setup can be used to reinstall drivers or select software that has been corrupted or deleted from the system. 92 1. From the Start screen, type HP Software Setup, and select apps. 2. Open HP Software Setup. 3. Follow the on-screen instructions to reinstall drivers or select software.
12 Computer Setup (BIOS) and Advanced System Diagnostics Using Computer Setup Computer Setup, or Basic Input/Output System (BIOS), controls communication between all the input and output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Computer Setup includes settings for the types of devices installed, the startup sequence of the computer, and the amount of system and extended memory. NOTE: Use extreme care when making changes in Computer Setup.
To exit Computer Setup menus, choose one of the following methods: ● To exit Computer Setup menus without saving your changes: Click the Exit icon in the lower-left corner of the screen, and then follow the on-screen instructions. – or – Use the tab key and the arrow keys to select File > Ignore Changes and Exit, and then press enter. ● To save your changes and exit Computer Setup menus: Click the Save icon in the lower-left corner of the screen, and then follow the on-screen instructions.
Updating the BIOS Updated versions of the BIOS may be available on the HP website. Most BIOS updates on the HP website are packaged in compressed files called SoftPaqs. Some download packages contain a file named Readme.txt, which contains information regarding installing and troubleshooting the file.
NOTE: If you connect your computer to a network, consult the network administrator before installing any software updates, especially system BIOS updates. BIOS installation procedures vary. Follow any instructions that are displayed on the screen after the download is complete. If no instructions are displayed, follow these steps: 1. From the Start screen, type windows, and then click Windows Explorer. 2. Double-click your hard drive designation. The hard drive designation is typically Local Disk (C:).
To start Advanced System Diagnostics: 1. Turn on or restart the computer. While the “Press the ESC key for Startup Menu” message is displayed in the lower-left corner of the screen, press esc. When the Startup Menu is displayed, press f2. 2. Click the diagnostic test you want to run, and then follow the on-screen instructions. NOTE: If you need to stop a diagnostics test while it is running, press esc.
13 Support Contacting support If the information provided in this user guide or Help and Support does not address your questions, you can contact support. For U.S. support, go to http://www.hp.com/go/contactHP. For worldwide support, go to http://welcome.hp.com/country/us/en/wwcontact_us.html. Here you can: ● Chat online with an HP technician. NOTE: When support chat is not available in a particular language, it is available in English. 98 ● E-mail support. ● Find support telephone numbers.
Labels The labels affixed to the computer provide information you may need when you troubleshoot system problems or travel internationally with the computer: ● Service label—Provides important information, including the following: Component (1) Product name (2) Serial number (s/n) (3) Part number/Product number (p/n) (4) Warranty period (5) Model description Have this information available when you contact support. The service label is affixed inside the battery bay.
14 Specifications ● Input power ● Operating environment 100 Chapter 14 Specifications
Input power The power information in this section may be helpful if you plan to travel internationally with the computer. The computer operates on DC power, which can be supplied by an AC or a DC power source. The AC power source must be rated at 100–240 V, 50–60 Hz. Although the computer can be powered from a standalone DC power source, it should be powered only with an AC adapter or a DC power source supplied and approved by HP for use with this computer.
Operating environment Factor Metric U.S.
A Traveling with the computer For best results, follow these traveling and shipping tips: ● Prepare the computer for traveling or shipping: ◦ Back up your information. ◦ Remove all discs and all external media cards, such as digital cards. CAUTION: To reduce the risk of damage to the computer, damage to a drive, or loss of information, remove the media from a drive before removing the drive from a drive bay and before shipping, storing, or traveling with a drive.
hazardous locations. If you are uncertain of the policy that applies to the use of a particular device, ask for authorization to use it before you turn it on. ● If you are traveling internationally, follow these suggestions: ◦ Check the computer-related customs regulations for each country or region on your itinerary. ◦ Check the power cord and adapter requirements for each location in which you plan to use the computer. Voltage, frequency, and plug configurations vary.
B Troubleshooting Troubleshooting resources ● Access website links and additional information about the computer through Help and Support. From the Start screen, type help, and then select Help and Support. NOTE: Some checkup and repair tools require an Internet connection. HP also provides additional tools that do not require an Internet connection. ● Contact HP support. For U.S. support, go to http://www.hp.com/go/contactHP. For worldwide support, go to http://welcome.hp.
The computer screen is blank If the screen is blank but you have not turned off the computer, one or more of these settings may be the cause: ● The computer may be in the Sleep state. To exit Sleep, briefly press the power button. Sleep is an energy-saving feature that turns off the display. Sleep can be initiated by the system while the computer is on but is not in use, or when the computer has reached a low battery level.
An external device is not working Follow these suggestions if an external device does not function as expected: ● Turn on the device according to the manufacturer's instructions. ● Be sure that all device connections are secure. ● Be sure that the device is receiving electrical power. ● Be sure that the device, especially if it is older, is compatible with the operating system. ● Be sure that the correct drivers are installed and updated.
The optical disc tray does not open for removal of a CD or DVD 1. Insert the end of a paper clip (1) into the release access in the front bezel of the drive. 2. Press in gently on the paper clip until the disc tray is released, and then pull out the tray (2) until it stops. 3. Remove the disc (3) from the tray by gently pressing down on the spindle while lifting the outer edges of the disc. Hold the disc by the edges and avoid touching the flat surfaces.
The computer does not detect the optical drive If your operating system does not detect an installed device, the device driver software may be missing or corrupted. 1. Remove any discs from the optical drive. 2. Click Computer and then click System Monitor. 3. From the Hardware tab, identify the Storage Controller in the Type column. 4. Click the triangle next to the devices until you locate your optical drive. If the drive is listed, it should be functioning correctly.
The process of burning a disc does not begin, or it stops before completion ● Be sure that all other programs are closed. ● Turn off Sleep mode. ● Be sure that you are using the right kind of disc for your drive. ● Be sure that the disc is inserted properly. ● Select a slower write speed and try again. ● If you are copying a disc, save the information on the source disc to your hard drive before trying to burn the contents to a new disc, and then burn from your hard drive.
C Electrostatic discharge Electrostatic discharge is the release of static electricity when two objects come into contact—for example, the shock you receive when you walk across the carpet and touch a metal door knob. A discharge of static electricity from fingers or other electrostatic conductors may damage electronic components.
Index A AC adapter light 13, 16 AC adapter, testing 49 administrator password 72 advanced system diagnostics 96 airport security devices 56 antivirus software 79 audio functions, checking 37 audio-in (microphone) jack 12 audio-out (headphone) jack 12 Automatic DriveLock password entering 78 removing 78 B Backup and Restore 89 battery conserving power 47 discharging 45 displaying remaining charge 45 disposing 48 low battery levels 45 replacing 48 storing 48 battery bay 19, 99 Battery Check 45 battery inform
F f11 recovery 90 Face Recognition 38 face recognition 70 fingerprint reader 81 fingerprint reader, identifying 8, 9 firewall software 79 fn key, identifying 10, 11, 32, 33 function keys identifying 10, 11 G GPS 25 graphics modes, switching 50 H hard drive external 55 HP 3D DriveGuard 64 installing 61 removing 59 hard drive bay, identifying 19 hard drive light 12, 64 hard drive recovery 90 HDMI port, connecting 39 HDMI port, identifying 15, 16 HDMI, configuring audio 39 Hibernation exiting 42 initiating 4
optical disc inserting 65 removing 67 optical drive 55 optical drive eject button 13, 14 optical drive light 13, 14 optical drive, identifying 13, 14 optional external devices, using 55 P passwords administrator 72 BIOS administrator 74 DriveLock 75 user 72 pinching TouchPad gesture 31 pointing devices, setting preferences 28 ports external monitor 15, 16, 38 HDMI 15, 16, 39 Intel Wireless Display 40 USB 13, 14, 15, 16 VGA 38 power battery 44 conserving 47 options 42 power button 41 power button, identifyin
W Web browser button, identifying 8, 9 Web browser light 5, 6 webcam 38 webcam light, identifying 17, 18 webcam, identifying 17, 18 Windows 8 operating system media 91 Windows applications key, identifying 10, 11 Windows logo key, identifying 10, 11 wireless antennas, identifying 17, 18 wireless button 22 wireless button, identifying 8, 9 wireless certification label 99 wireless controls button 22 operating system 22 wireless light 5, 6, 22 wireless module compartment 19 wireless network (WLAN) connecting 2