Installation Guide

ManualsBrandsRaspberry Pi ManualsElectronicsRadio module

Table Of Contents

Installation Guide for Raspberry Pi Zero 2

Module Integration

1. Purpose

The purpose of this document is to provide information on how to use a Raspberry Pi Zero 2 as a

radio module when integrating into a host product.

Incorrect integration or use may infringe compliance rules meaning recertification may be required.

2. Module Description

The Raspberry Pi Zero 2 module has an IEEE 802.11b/g/n 1x1 WLAN, Bluetooth 5 and Bluetooth LE

module based on the Cypress 43439 chip. The module is designed to be mounted, with appropriate

screws, into an host product. The module must be placed in a suitable location to ensure WLAN

performance is not compromised.

Summary of content (9 pages)

PAGE 1
Installation Guide for Raspberry Pi Zero 2 Module Integration 1. Purpose The purpose of this document is to provide information on how to use a Raspberry Pi Zero 2 as a radio module when integrating into a host product. Incorrect integration or use may infringe compliance rules meaning recertification may be required. 2. Module Description The Raspberry Pi Zero 2 module has an IEEE 802.11b/g/n 1x1 WLAN, Bluetooth 5 and Bluetooth LE module based on the Cypress 43439 chip.
PAGE 2
3. Integration into Products Module & Antenna Placement A separation distance greater than 20cm will always be maintained between the antenna and any other radio transmitter if installed in the same product. The module is physically attached and held in place by screws In order to connect the module to the system micro USB power cable is connected to J1 on the board. The supply should be 5V DC minimum 2A. Power can also be supplied on the 40 Pin GPIO header (J8); Pins 1 + 3 connected to 5V and pin 5 to GND.
PAGE 3
Dependent on intended usage the following ports can / should be connected; Mini HDMI USB2.0 ports CSI Camera (for use with Official Raspberry Pi Camera module, sold separately) SD card USB3.0 CAMERA USB2.0 Micro USB Power Micro USB Micro HDMI Any external power supply used with the Raspberry-Pi shall comply with relevant regulations and standards applicable in the country of intended use. At no point should any part of the board be altered as this will invalidate any existing compliance work.
PAGE 4
5. End Product Labelling A label is to be fitted to the exterior of all products containing the Raspberry Pi Zero 2 module. The label must contain the words “Contains FCC ID: 2ABCB-RPIZ2” (for FCC) and “Contains IC: 20953RPIZ2” (for ISED).
PAGE 5
This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter except in accordance with FCC’s multi-transmitter procedures. IMPORTANT NOTE: FCC Radiation Exposure Statement; Co-location of this module with other transmitter that operate simultaneously are required to be evaluated using the FCC multitransmitter procedures. This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
PAGE 6
ISED Raspberry Pi Zero 2 IC: 20953-RPIZ2 This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
PAGE 7
INTEGRATION INFORMATION FOR THE OEM It is the responsibility of the OEM / Host product manufacturer to ensure continued compliance to FCC and ISED Canada certification requirements once the module is integrated in to the Host product. Please refer to FCC KDB 996369 D04 for additional information. The module is subject to the following FCC rule parts: 15.207, 15.209, 15.
PAGE 8
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
PAGE 9
E-Labelling It is possible for the Host product to use e-labelling providing the Host product supports the requirements of FCC KDB 784748 D02 e labelling and ISED Canada RSS-Gen, section 4.4. E-labelling would be applicable for the FCC ID, ISED Canada certification number and the FCC Part 15 text. Changes in Usage Conditions of this Module This device has been approved as a Mobile device in accordance with FCC and ISED Canada requirement.