Installation guide

ManualsBrandsSecurity Command ManualsHome building and DecorXR40

InstallatIon GuIde

1101 Universal Transmitter

Description

The 1101 is a two input transmitter that is typically used for door/window applications. The 1101 provides two

internal magnetic reed switches and an on-board terminal block to allow for external contact wiring. Both sets

of contacts, internal and external, can be programmed to operate at the same time allowing for two independent

zones from one transmitter. Refer to the panel programming guide for zone programming information.

Using the on-board LED the 1101 Universal Transmitter provides built-in survey capability to allow for single-person

installations, eliminating the requirement for an external survey kit. A transmitter mounting bracket is included to

make the installation quick and easy. For added security, an internal case tamper switch is provided.

The 1101 Transmitter operates with the XR500 Series Command Processor™ panels or XR100 Series Command

Processor™ panels using the 1100X Receiver or with the XRSuper6, XR20, and XR40 Command Processor™ panels using

the 1100D Receiver.

What is Included

The 1101 Universal Transmitter includes the following

items:

• One1101TransmitterPCBmountedinatwo-part

housing (base and cover)

• OneMagnethousingandbase

• One3VlithiumCR123ABattery

• Hardwarepack

• Zonenameandnumberlabel

• Serialnumberlabel

• OptionalTransmittermountingbracket

• Optionalmagnetmountingspacer

• Optionaldouble-sidedtape

Transmitter Serial Number

For your convenience, an additional pre-printed serial number label is included. Prior to installing the device,

record the serial number or place the pre-printed serial number label on the panel programming sheet. This number

is required during programming.Asneeded,usethezonenameandnumberlabeltoidentifyaspecictransmitter.

Programming the Transmitter in the Panel

Refer to the XR500 Series Programming Guide (LT-0679), XR100 Series Programming Guide (LT-0896), or the

XRSuper6/XR20/XR40ProgrammingGuide(LT-0305)asneeded.ProgramthedeviceasazoneinZone Information

during panel programming. At the Serial Number: prompt, enter the eight-digit serial number, including leading

zeros. Continue to program the zone as directed in the panel programming guide.

Note: When a receiver is installed, powered up, or the panel is reset, the supervision time for transmitters is reset.

If the receiver has been powered down for more than one hour, wireless transmitters may take up to an additional

hour to send a supervision message unless tripped, tampered, or powered up. This operation extends battery life for

transmitters. A missing message may display on the keypad until the transmitter sends a supervision message.

Selecting the Proper Location (LED Survey Operation)

The1101Transmitterprovidesasurveycapabilitytoallowonepersontoconrmtransmittercommunicationwith

the receiver while the cover is removed. The 1101 Transmitter PCB Red Survey LED turns on whenever data is

sent to the receiver then immediately turns off when the receiver acknowledgement is received. Pressing the

tamperswitchisaconvenientwaytosenddatatothereceivertoconrmoperation.Whenthetamperswitch

is pressed or released, the LED blinks once to indicate proper operation. When the transmitter does not receive

an acknowledgement from the receiver the LED remains on for about 8 seconds to let you know communication is

notestablished.CommunicationisalsofaultywhentheLEDashesmultipletimesinquicksuccession.Relocate

the transmitter or receiver until the LED immediately turns off indicating the transmitter and receiver are

communicatingproperly.Propercommunicationbetweenthetransmitterandreceiverisveriedwhenforeach

press or release of the tamper switch, the LED blinks immediately on and immediately off. Repeat this test to

conrmveseparateconsecutiveLEDblinks.Anyindicationotherwisemeanspropercommunicationhasnotbeen

established.

Figure 1: Mounted Transmitter and Magnet

1101 Universal

Transmitter

Magnet

Housing

Ensure there is 5/8" or less

betweentheassembledMagnet

HousingandTransmitterHousing.

Squeeze External

Case Ends together to

Remove Cover

Squeeze External

Case Ends together

to Remove Cover

www.BevanSecurity.Com

Summary of content (4 pages)

PAGE 1
Installation Guide 1101 Universal Transmitter Description The 1101 is a two input transmitter that is typically used for door/window applications. The 1101 provides two internal magnetic reed switches and an on-board terminal block to allow for external contact wiring. Both sets of contacts, internal and external, can be programmed to operate at the same time allowing for two independent zones from one transmitter. Refer to the panel programming guide for zone programming information.
PAGE 2
Mounting the Transmitter and Magnet Assemblies For internal contact operation, the transmitter and magnet assembly should have no more than 5/8" space between the assembled housings after installation. When mounting on metal (ferrous) surfaces, this distance is slightly less. For door installations, it is recommended the transmitter be mounted on the door frame and the magnet assembly be mounted on the door. Magnet Housing and Base Only one magnet assembly is required for internal reed switch operation.
PAGE 3
Installing the Transmitter without the Mounting Bracket These instructions cover installing the transmitter using the base housing without the mounting bracket. If the installation requires the mounting bracket, refer to Installing the Optional Mounting Bracket above. 1. Remove the battery if installed. 2. Hold the transmitter base in place with the reed switch nearest to the area where you plan to mount the magnet. 3.
PAGE 4
Battery Life Expectancy Typical battery life expectancy for DMP Model 1101 wireless transmitters is 5 years. DMP wireless equipment uses two-way communication to extend battery life. The following situations can reduce battery life expectancy: • If a receiver is unplugged or not installed. Note: Transmitters continue to send supervision messages until a receiver returns an acknowledgement. After an hour the transmitter only attempts a supervision message every 60 minutes.