ITDB-100L Barcode Reader MODEL: ITDB-100L 2D Barcode Reader RoHS Compliant User Manual Page i Rev. 1.
ITDB-100L Barcode Reader Revision Date Version Changes 7 April, 2014 1.02 Updated Chapter 5 for the latest setup tool version 13 March, 2014 1.01 Updated for the latest hardware, specifications and application version Added Chapter 6: Configuring the ITDB-100L via an Android Device 25 July, 2013 Page ii 1.
ITDB-100L Barcode Reader Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
ITDB-100L Barcode Reader Table of Contents 1 INTRODUCTION.......................................................................................................... 1 1.1 OVERVIEW.................................................................................................................. 2 1.2 FEATURES ................................................................................................................... 2 1.3 EXTERNAL OVERVIEW ...............................................................
ITDB-100L Barcode Reader 3.4 READING DISTANCE AND FIELD OF VIEW ................................................................. 26 4 DRIVER AND PC SETUP TOOL INSTALLATION ............................................... 27 4.1 OVERVIEW................................................................................................................ 28 4.2 DRIVER INSTALLATION ............................................................................................. 28 4.3 SETUP TOOL INSTALLATION ...........
ITDB-100L Barcode Reader 6.5.6 Parameter Settings........................................................................................... 63 6.5.6.1 Automatic Setting...................................................................................... 63 6.5.6.2 LED Brightness......................................................................................... 64 6.5.6.3 Exposure Time .......................................................................................... 65 6.5.6.
ITDB-100L Barcode Reader List of Figures Figure 1-1: ITDB-100L ....................................................................................................................2 Figure 1-2: ITDB-100L Front Panel................................................................................................3 Figure 1-3: ITDB-100L Rear Panel.................................................................................................4 Figure 1-4: ITDB-100L Bottom Surface................................
ITDB-100L Barcode Reader Figure 5-3: Detecting the Available Connection Type ..............................................................38 Figure 5-4: Connection Type Selection ......................................................................................38 Figure 5-5: Connection Status ....................................................................................................39 Figure 5-6: Auto Setup .......................................................................................
ITDB-100L Barcode Reader List of Tables Table 1-1: Technical Specifications..............................................................................................6 Table 3-1: Connector Pinouts......................................................................................................
ITDB-100L Barcode Reader Chapter 1 1 Introduction Page 1
ITDB-100L Barcode Reader 1.1 Overview Figure 1-1: ITDB-100L The ITDB-100L barcode reader is able to provide high-speed decoding and robust decoding for common distortion, which is suitable for industrial purpose such as the high-speed production line. In addition, the ITDB-100L comes with a PC setup tool for configuring the barcode reader and reading barcodes. 1.
ITDB-100L Barcode Reader 1.3 External Overview 1.3.1 Front Panel The ITDB-100L front panel contains: 2 x Illumination LEDs 1 x Lens An overview of the front panel is shown in Figure 1-2. 6 Figure 1-2: ITDB-100L Front Panel 1.3.
ITDB-100L Barcode Reader An overview of the rear panel is shown in Figure 1-3 below. 6 Figure 1-3: ITDB-100L Rear Panel 1.3.3 Bottom Surface The bottom surface of the ITDB-100L contains four retention screw holes for the mounting bracket.
ITDB-100L Barcode Reader 1.4 Technical Specifications The ITDB-100L technical specifications are listed in Table 1-1. Specifications Supported 1D Symbologies Supported 2D Symbologies Code 39, code 93, interleaved 2 of 5, UPC/EAN (ISBN, UPCA, UPCE, EAN13, EAN8), EAN 128, code 128, MSI, codabar PDF-417, Micro PDF-417, QR Code/microQR Code, Data Matrix Sensor: 1/3 inch CMOS with global shutter Sensor Major Specifications Resolution: 752 x 480 Acquisition: Max.
ITDB-100L Barcode Reader Specifications Operating voltage: 12V/3.3A Power Supply Power consumption: Power on = 7.7 W Max. PD = 9.9 W Microsoft® Windows® XP 32-bit & 64-bit Supported OS Microsoft® Windows® Vista™ 32-bit & 64-bit Microsoft® Windows® 7 32-bit & 64-bit Housing: Die-casting aluminum Housing color: Silver Mechanical Specifications Front cover: Transparent plastic Weight: 290 g (without mounting bracket) Dimensions (LxWxH): 89.
ITDB-100L Barcode Reader 1.5 Dimensions 1.5.
ITDB-100L Barcode Reader 1.5.
ITDB-100L Barcode Reader 1.6 ITDB-100L Function Compatibility Guideline Function USB Connection (via API) LAN Connection* (via API) USB Connection (via API) O USB Keyboard Wedge (HID) Built-in Web Management X O X X O X X X LAN Connection* (via API) O USB Keyboard Wedge (HID) X X Transfer to Database O O X Built-in Web Management X X X O: Compatible Transfer to Database X X X: Incompatible * LAN connection interface includes the PC setup tool, Android app or QNAP NAS app.
ITDB-100L Barcode Reader Chapter 2 2 Unpacking Page 10
ITDB-100L Barcode Reader 2.1 Anti-static Precautions WARNING: Failure to take ESD precautions during installation may result in permanent damage to the ITDB-100L and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the ITDB-100L. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the ITDB-100L or any other electrical component is handled, the following anti-static precautions are strictly adhered to.
ITDB-100L Barcode Reader 2.3 Unpacking Checklist NOTE: If some of the components listed in the checklist below are missing, please do not proceed with the installation. Contact the IEI reseller or vendor you purchased the ITDB-100L from or contact an IEI sales representative directly. To contact an IEI sales representative, please send an email to sales@ieiworld.com.
ITDB-100L Barcode Reader Quantity Item Image Standard 1 Mounting bracket (P/N: 42110-0172C0-00-RS-N) 4 Mounting bracket screw (P/N: 44045-020061-RS) 1 Trigger connection cable 1 User manual and utility CD Page 13
ITDB-100L Barcode Reader Chapter 3 3 Installation Page 14
ITDB-100L Barcode Reader 3.1 Installation Precautions During installation, be aware of the precautions below: Read the user manual: The user manual provides a complete description of the ITDB-100L, installation instructions and configuration options. DANGER! Disconnect Power: Power to the ITDB-100L must be disconnected during the installation process. Failing to disconnect the power may cause severe injury to the body and/or damage to the system.
ITDB-100L Barcode Reader Figure 3-1: Securing the Mounting Bracket to the ITDB-100L Step 2: Mount the ITDB-100L to an object with corresponding mounting screw, for example, a tripod. Align the threaded hole on the mounting bracket with the mounting screw, place the ITDB-100L over the object, and then spin the ITDB-100L until it is secure to the object (Figure 3-2).
ITDB-100L Barcode Reader Figure 3-2: Mounting the ITDB-100L Step 3: To avoid reflection and glare from the scanned object and label surfaces, it is recommended to mount the barcode reader at a 15º angle from vertical to the scanned object (Figure 3-3).
ITDB-100L Barcode Reader Figure 3-3: Adjusting the ITDB-100L 3.3 External Peripheral Interface Connectors The ITDB-100L has the following connectors. Detailed descriptions of the connectors can be found in the subsections below. 6-pin connector for trigger connection Ethernet Micro USB Power input 3.3.1 6-Pin Connector for Trigger Connection The 6-pin connector on the rear panel allows connection to an external trigger device or a sensor.
ITDB-100L Barcode Reader Step 2: Align the connectors. Align the 6-pin plug on the trigger connection cable with the 6-pin connector on the ITDB-100L. See Figure 3-4. Figure 3-4: Trigger Connection Step 3: Insert the trigger connection cable 6-pin plug. Once aligned, gently insert the trigger connection cable 6-pin plug into the 6-pin connector on the ITDB-100L. Step 4: Connect the other end of the trigger connection cable to an external device.
ITDB-100L Barcode Reader Pin Color Signal 5 N/A (Reserved) 6 N/A (Reserved) Table 3-1: Connector Pinouts 3.3.1.1 Digital Output Wiring Figure 3-5: Digital Output Wiring 3.3.1.
ITDB-100L Barcode Reader 3.3.1.3 Digital Input and Output Connection The below figure demonstrates a possible way of digital input and output connection.
ITDB-100L Barcode Reader 3.3.2 Ethernet Connector The ITDB-100L is equipped with an Ethernet connector that allows connection to a computer/network hub. Follow the steps below to connect the ITDB-100L to a computer/network hub by using the supplied Ethernet cable. Step 1: Locate the Ethernet connector. The location of the Ethernet connector is shown in Figure 1-3. Step 2: Align the connectors. Align the Ethernet connector on the LAN cable with the Ethernet connector on the ITDB-100L. See Figure 3-8.
ITDB-100L Barcode Reader 3.3.2.1 Network Connection The below figure demonstrates a possible way of network connection.
ITDB-100L Barcode Reader 3.3.3 Micro USB Connector The ITDB-100L is equipped with a Micro USB connector that allows connection to a computer. Follow the steps below to connect the ITDB-100L to a computer by using the supplied Micro USB cable. Step 1: Locate the Micro USB connector. The location of the Micro USB connector is shown in Figure 1-3. Step 2: Align the Micro USB connectors. Align the Micro USB connector on the Micro USB cable with the Micro USB connector on the ITDB-100L. See Figure 3-10.
ITDB-100L Barcode Reader Figure 3-11: USB Standard Type A Connection 3.3.3.1 USB Keyboard Wedge After connecting the ITDB-100L to the USB port of a computer, the ITDB-100L will be recognized by the computer as a second keyboard. When the ITDB-100L scans a barcode without any API opened, the barcode data goes into the computer just as if it were being typed on a keyboard. 3.3.4 Power Input Connector Step 1: Locate the power input connector. The location of the power input connector is shown in Figure 1-3.
ITDB-100L Barcode Reader 3.4 Reading Distance and Field of View The following figure provides the supported reading distances and field of view for the ITDB-100L.
ITDB-100L Barcode Reader Chapter 4 4 Driver and PC Setup Tool Installation Page 27
ITDB-100L Barcode Reader 4.1 Overview A CD is shipped with the barcode reader. The CD contains the device driver and application setup file. The driver must be installed to the connected computer so that the barcode reader can be recognized by the system. 4.2 Driver Installation To install the device driver, please follow the steps below. Step 1: Connect the ITDB-100L to the computer and power supply. A beep should be generated when the ITDB-100L is fed with power.
ITDB-100L Barcode Reader Step 5: The Found New Hardware Wizard appears (Figure 4-2). Select No, not this time, then click Next to continue. Figure 4-2: Found New Hardware Wizard Step 6: Select Install from a list or specific location, then click Next to continue. (Figure 4-3).
ITDB-100L Barcode Reader Step 7: Insert the driver CD into an optical disk drive connected to the system. Step 8: Select Include this location in the search (Figure 4-4). Step 9: Click Browse to select “X:\” directory in the Locate File window, where “X:\” is the system CD drive. Figure 4-4: Locate Driver Files Step 10: Click Next to continue. Step 11: Driver Installation is performed as shown in Figure 4-5.
ITDB-100L Barcode Reader Figure 4-5: Driver Installation Step 12: When the driver installation is completed, the following window appears. Click Finish to exit.
ITDB-100L Barcode Reader 4.3 Setup Tool Installation To install the barcode reader setup tool, please follow the steps below. NOTE: The setup tool supports the following OS versions: Microsoft® Windows® XP 32-bit and 64-bit Microsoft® Windows® Vista™ 32-bit and 64-bit Microsoft® Windows® 7 32-bit and 64-bit Step 1: Ensure that the ITDB-100L is connected to the computer and power supply. If the barcode reader cannot be recognized by the computer, install the device driver. Refer to Section 4.
ITDB-100L Barcode Reader Step 5: Select a folder for application installation (Figure 4-8). Click Next to continue. Figure 4-8: Select Installation Folder Step 6: The following screen appears. Click Install to start the installation. Figure 4-9: Ready for Installation Step 7: The system starts installing the application.
ITDB-100L Barcode Reader Step 8: When the application installation is completed, the following window appears. Click Finish to exit.
ITDB-100L Barcode Reader Chapter 5 5 Barcode Reader Setup Tool Page 35
ITDB-100L Barcode Reader 5.1 Overview The barcode reader setup tool allows configuration of the ITDB-100L via a computer. Refer to the following sections for detailed information. NOTE: The setup tool supports the OS versions listed below: Microsoft® Windows® XP 32-bit & 64-bit Microsoft® Windows® Vista™ 32-bit & 64-bit Microsoft® Windows® 7 32-bit & 64-bit 5.2 Launching the Setup Tool Step 1: Ensure that the ITDB-100L is connected to the computer and power supply.
ITDB-100L Barcode Reader 5.3 Initial Screen After double-clicking the ITDB Barcode Verifier icon on the Windows desktop, the initial screen of the setup tool appears (Figure 5-2). Click Sync Settings & Decode Now to enter the SETTING menu. When using the setup tool for the first time, refer to Section 5.4. Figure 5-2: Initial Screen 5.4 Initial Setting Step 1: When using the setup tool for the first time, click Initial Setting in the initial screen (Figure 5-2).
ITDB-100L Barcode Reader Figure 5-3: Detecting the Available Connection Type Step 3: Click LAN or Micro USB depending on the connection type to the computer (Figure 5-4). A confirmation dialog screen should appear. Click OK to confirm the selection.
ITDB-100L Barcode Reader Step 4: When the connection is complete, two beeps should be generated, and the connection status field displays Connected as shown in Figure 5-5. Figure 5-5: Connection Status Step 5: In the Configuration page (Figure 5-5), click Manual Setup to enter the SETTING menu to configure the barcode reader settings manually. For automatic setup, refer to Section 5.5 for details. 5.
ITDB-100L Barcode Reader Figure 5-6: Auto Setup Step 2: Automatic setup is performed as shown in Figure 5-7. Figure 5-7: Automatic Setup Step 3: When the setup is complete, the screen in Figure 5-8 appears. Click NEXT to enter the VERIFICATION menu. If automatic setup is failed, click Retry to start automatic setup again.
ITDB-100L Barcode Reader Figure 5-8: Setup Complete 5.6 Verification Menu In the VERIFICATION menu, the user can set up the trigger behavior, scanned result format and region of interest, load scanned images, and set a barcode image to training mode.
ITDB-100L Barcode Reader Trigger mode: The user can set the trigger behavior as One Shot, Serial Shot, Batch or Presentation. When setting to Serial Shot, the ITDB-100L scan images continuously until an image is decoded successfully. Decode result format: The user can set the scanned result format as Image & Decode, Image or Decode. Trigger button: The user can click the button to trigger the ITDB-100L. 5.6.
ITDB-100L Barcode Reader Figure 5-11: Locking the ROI Setting 5.6.2 Training Mode The user can set a scanned barcode as a sample image so that the barcode reader decodes only the same barcode type and size. Follow the steps below to set a barcode image to training mode. Step 1: Click the Train Code item (Figure 5-12) to start the training mode function. The user can also press and hold the trigger and tuning control button for four seconds to start the function.
ITDB-100L Barcode Reader Figure 5-12: Train Code Item Step 2: Four beeps are being generated, the illumination LEDs start to flash and the screen in Figure 5-13 appears, indicating that the training mode timer is started. Figure 5-13: Training Mode Timer is Started Step 3: The user has to click the Click And Train button (Figure 5-13) to trigger the ITDB-100L within twelve seconds after the timer is started.
ITDB-100L Barcode Reader Figure 5-14: Trained Mode Step 5: To disable the training mode, click the Train Code item or press and hold the trigger and tuning control button for four seconds. 5.6.3 Loading Saved Images The user can load the saved images to view their detailed information. When a scanned barcode is being saved, it should be stored to the Save Image folder located at the same folder where the setup tool has been installed.
ITDB-100L Barcode Reader To load all the images of a folder or selected images: To load all the images of a folder or selected images, click the icon indicated in Figure 5-16, and then select to load images by folder or by selection.
ITDB-100L Barcode Reader 5.7 Settings Menu Click SETTING to display the Settings menu (Figure 5-17). In this menu, the user can configure detailed settings for the barcode reader. Figure 5-17: Settings Trigger mode: The user can set the trigger behavior as One Shot, Serial Shot, Batch or Presentation. When setting to Serial Shot, the ITDB-100L scans images continuously until an image is decoded successfully.
ITDB-100L Barcode Reader Manual Exposure: Move the slide bar or enter the value to set the exposure time. GAIN: Move the slide bar or enter the value to adjust the gain setting. LED Brightness: Move the slide bar or enter the value to adjust the LED brightness. Decode timeout(ms): Move the slide bar or enter the value to adjust the decode time-out setting. Decode interval(ms): Move the slide bar or enter the value to adjust the decode interval setting. Train Code: Refer to Section 5.
ITDB-100L Barcode Reader Figure 5-18: Symbology Settings 5.8 Network Menu Click NETWORK on the left pane of the setup tool to bring up the Network Setting menu (Figure 5-19). In this menu, the user can configure network settings and set up a device name for the barcode reader.
ITDB-100L Barcode Reader Address: Click DHCP to enable the DHCP function or set up the IP address, mask and gateway manually. Server IP: Click Enable, enter the server IP, and then click Save IP to save the keyed-in server IP. DNS IP: Click Enable, enter the DNS IP, and then click Save DNS IP to save the keyed-in DNS IP. Device Name: Enter a name and click Set Device Name to set up a device name for the barcode reader. 5.
ITDB-100L Barcode Reader Figure 5-20: Change Password Page 51
ITDB-100L Barcode Reader 5.10 FW Upgrade and Backup Mode This section covers how to upgrade the device FW and enter the backup mode when the FW upgrade is failed or the ITDB-100L is failed to restart. 5.10.1 FW Upgrade Flow Chart Start Remove the power supply Upgrade the FW (refer to Section 5.9.2) Reconnect the power supply and enter the Backup Mode (refer to Section 5.9.3) The ITDB-100L restarts automatically. Upgrade the FW (refer to Section 5.9.
ITDB-100L Barcode Reader 5.10.2 Upgrading the FW Follow the steps below to upgrade the FW. Step 1: Click FIRMWARE on the left pane of the setup tool to bring up the Firmware Upgrade menu (Figure 5-21). The user can check the current firmware version from the menu. Step 2: Click Path to locate the firmware file. Step 3: Click Upgrade F/W to start updating the firmware. Figure 5-21: FW Upgrade Step 4: When the FW upgrade is complete, the ITDB-100L restarts automatically.
ITDB-100L Barcode Reader 5.10.3 Backup Mode When the FW upgrade is failed or the ITDB-100L is failed to reboot, the ITDB-100L needs to enter the backup mode and upgrade the FW in the backup mode. Follow the steps below to enter and exit the backup mode. Step 1: Before the ITDB-100L is connected to the power supply, press and hold the trigger and tuning control button. Refer to Figure 1-3 for the location of the button. Step 2: Connect the ITDB-100L to the power supply.
ITDB-100L Barcode Reader Chapter 6 6 Configuring the ITDB-100L via an Android Device Page 55
ITDB-100L Barcode Reader 6.1 Overview The barcode reader settings can be configured by an Android device. Refer to the following sections for detailed information. NOTE: The screenshots in this chapter may vary by different Android devices and are for reference purposes only. 6.2 Installing and Launching the Android App NOTE: It is recommended to install the app to the Android OS 4.1.2 and above. To install and launch the Android app, please follow the steps below.
ITDB-100L Barcode Reader Figure 6-1: App Icon Step 3: Tap the app icon to launch it.
ITDB-100L Barcode Reader 6.3 Settings Menu The initial screen of the app is a settings menu, allowing the user to set up the captured image format and the maximum quantity of captured images (Figure 6-2). When the settings are done, tap OK to enter the barcode reader list screen. Figure 6-2: Settings Menu Image Format: Sets up the captured image format between Bitmap or Jpeg. Maximum of recording images: Sets up the maximum quantity of captured images.
ITDB-100L Barcode Reader 6.4 Barcode Reader List NOTE: Ensure that the DHCP Server function of the wireless router is turned off. To disable the DHCP Server function, refer to the user manual of the wireless router. The barcode reader list screen displays the ITDB-100L barcode readers found by the Android device and allows the user to select a barcode reader to configure its settings.
ITDB-100L Barcode Reader 6.5 Configuring the Barcode Reader to Decode an Image Successfully When a barcode reader is selected in the barcode reader list screen, the screen in Figure 6-4 will be shown. Refer to the following subsections to configure the selected barcode reader so that a barcode image can be decoded successfully. Figure 6-4: Decoding Image Screen 6.5.1 Live View Function The live view function allows the user to preview the barcode. Follow the steps below to use the live view function.
ITDB-100L Barcode Reader Step 1: Switch the capture mode icon to . Step 2: Adjust the barcode reader or scanned object until the barcode is shown on the scan area screen. 6.5.2 Using the External Sensor to Trigger the Barcode Reader Follow the steps below to use the external sensor to trigger the barcode reader. Step 1: Switch the capture mode icon to . Step 2: When the external sensor triggers the barcode reader, the captured image and decoding result will be shown on the screen. 6.5.
ITDB-100L Barcode Reader 6.5.5 Setting an Image to Training Mode The user can set a scanned barcode as a sample image so that the barcode reader decodes only the same barcode type and size. Follow the steps below to set a barcode image to training mode by using the Android app. NOTE: The training mode function can also be enabled by using the PC setup tool or the trigger and tuning control button. Refer to Section 5.6.2 for details. Step 1: Tap to start the training mode function.
ITDB-100L Barcode Reader 6.5.6 Parameter Settings Tap to bring up the parameter settings bar at the bottom of the screen as shwon in Figure 6-5. Figure 6-5: Parameter Settings 6.5.6.1 Automatic Setting The (automatic) option allows the barcode reader to adjust to its optimal settings according to the barcode reading environment. Step 1: Tap to start automatic setting. Step 2: Tap to stop automatic setting.
ITDB-100L Barcode Reader key on the Android device to return to the barcode reader list screen. Then the automatic setting parameters will be stored to the barcode reader. Step 4: When the automatic setting is failed, the message will appear, and the atutomatic setting process will stop. Then all the parameters will be restored to the last-saved settings. 6.5.6.2 LED Brightness The (LED brightness) option allows the user to adjust the LED brightness.
ITDB-100L Barcode Reader 6.5.6.3 Exposure Time The (exposure time) option allows the user to adjust the exposure time. Step 1: Tap , then drag the slider at the bottom of the screen (Figure 6-7) to adjust the exposure time. Figure 6-7: Exposure Time Step 2: Tap or the Back key on the Android device to return to the barcode reader list screen. Then the exposure time parameter will be stored to the barcode reader. 6.5.6.4 Gain Parameter The (gain) option allows the user to adjust the gain parameter.
ITDB-100L Barcode Reader Figure 6-8: Gain Parameter Step 2: Tap or the Back key on the Android device to return to the barcode reader list screen. Then the gain parameter will be stored to the barcode reader. 6.5.6.5 Decoding Time The user may need to increase the decoding time when the scanned barcode is complicated or the reading environment is bad. Step 1: Tap , then drag the slider at the bottom of the screen (Figure 6-9) to adjust the decoding time.
ITDB-100L Barcode Reader Figure 6-9: Decoding Time Step 2: Tap or the Back key on the Android device to return to the barcode reader list screen. Then the decoding time parameter will be stored to the barcode reader. 6.6 Checking the Decoded Images The parameter values of each captured image are displayed below the image (Figure 6-10). 6.6.1 Checking Captured Images Follow the steps below to check the captured images stored in the Android device.
ITDB-100L Barcode Reader Step 3: Tap barcode to display the captured images. The captured images are stored in /storage/sdcard0/Pictures/barcode of the Android device. Step 4: Tap an image to check its parameter values. The parameter values of each captured image are displayed below the image (Figure 6-10). Figure 6-10: Parameter Values 6.6.2 Sending an Captured Image to IEI The user might need to report a failed-decoded image to IEI for analyzing. Follow the steps below to complete the task.
ITDB-100L Barcode Reader Step 1: Repeat Step 1 ~ Step 4 in previous section. Step 2: Tap the image to bring up the toolbar. Step 3: Tap Share, then select e-mail to send the selected image to IEI.
ITDB-100L Barcode Reader Appendix A A Safety Precautions Page 70
ITDB-100L Barcode Reader A.1 Safety Precautions WARNING: The precautions outlined in this appendix should be strictly followed. Failure to follow these precautions may result in permanent damage to the ITDB-100L. Please follow the safety precautions outlined in the sections that follow: A.1.1 General Safety Precautions Please ensure the following safety precautions are adhered to at all times.
ITDB-100L Barcode Reader A.1.2 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the ITDB-100L may result in permanent damage to the ITDB-100L and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the ITDB-100L. Dry climates are especially susceptible to ESD.
ITDB-100L Barcode Reader A.1.3 Product Disposal CAUTION: Risk of explosion if battery is replaced by an incorrect type. Only certified engineers should replace the on-board battery. Dispose of used batteries according to instructions and local regulations. Outside the European Union - If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority so as to comply with the correct disposal method.
ITDB-100L Barcode Reader Be cautious of all small removable components when vacuuming the ITDB-100L. Turn the ITDB-100L off before cleaning the ITDB-100L. Never drop any objects or liquids through the openings of the ITDB-100L. Be cautious of any possible allergic reactions to solvents or chemicals used when cleaning the ITDB-100L. Avoid eating, drinking and smoking within vicinity of the ITDB-100L. A.2.
ITDB-100L Barcode Reader Appendix B B Hazardous Materials Disclosure Page 75
ITDB-100L Barcode Reader B.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
ITDB-100L Barcode Reader Part Name Toxic or Hazardous Substances and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated (Pb) (Hg) (Cd) Chromium Biphenyls Diphenyl (CR(VI)) (PBB) Ethers (PBDE) Housing O O O O O O Display O O O O O O Printed Circuit O O O O O O O O O O O O O O O O O O Fan Assembly O O O O O O Power Supply O O O O O O O O O O O O Board Metal Fasteners Cable Assembly Assemblies Battery O: This toxic or ha
ITDB-100L Barcode Reader 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符 合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的 年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元 件将会单独标示出来。 部件名称 有毒有害物质或元素 铅 汞 镉 六价铬 多溴联苯 多溴二苯 (Pb) (Hg) (Cd) (CR(VI)) (PBB) 醚 (PBDE) 壳体 O O O O O O 显示 O O O O O O 印刷电路板 O O O O O O 金属螺帽 O O O O O O 电缆组装 O O O O O O 风扇组装 O O O O O O 电力供应组装 O O O O O O 电池 O O O O O O O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要
