User's Manual
Table Of Contents
- Home
- Contents
- CSI 2140 Machinery Health Analyzer
- Introduction to the analyzer
- Transfer files with CSI 2140
- AMS Machinery Manager Data Transfer
- AMS Machinery Manager Standalone Data Transfer application
- Communication setup
- Routes and jobs
- Load a route from AMS Machinery Manager into the analyzer
- Load multiple routes from AMS Machinery Manager to the analyzer
- Load a Balance job from AMS Machinery Manager into the analyzer
- Dump a job from the analyzer to AMS Machinery Manager
- Dump a route from the analyzer to AMS Machinery Manager
- Dump a route or job from the analyzer to a folder on a computer
- Analyzer firmware and programs
- Screen captures
- Splash screens
- Printing
- Route
- Route overview
- Manage routes
- Set data collection and display parameters
- Set the plot type for collected data
- Enable or disable Point Advance to automatically move to the next measurement point
- Set High Frequency Detection averages
- Set the route data storage mode
- Set the overlap
- Set the plot type for live data
- Set the overall mode
- Set the integrate mode
- Enable or disable multi-channel group data collection
- Display a summary of data collected for grouped measurement points
- View or hide warning alarms on the Route Data Collection screen
- Restore default values for route data collection and display parameters
- Override the sensor setup for a route
- Enter new speed or load for a measurement point
- Tachometers
- Multiple inputs and measurements
- Collect route data
- Notes
- Plot data
- Run Analyze to collect data for a route measurement point
- View the measurement point setup and history
- Route reports
- Plots
- Analyze and Advanced Analyze
- Analyze overview
- Manage jobs
- Job Setup
- View all saved Analyze jobs
- Create an Analyze job
- Open a saved Analyze job
- Change the job ID
- Edit the equipment ID and description in a job
- Edit the measurement ID and description in a job
- Add a measurement
- Delete a measurement
- Delete data from the current measurement point
- Save a job to equipment in a route
- Set display parameters
- Multi-input measurements
- Sensors and inputs
- Tachometers
- Common data collection parameters
- Collecting data using an Analysis Expert
- Recommended uses of Analysis Experts
- Enable or disable the help text in the Analysis Experts
- High Frequency Analysis
- High Resolution Analysis
- Bearing/Gear Analysis - PeakVue
- Low Frequency Analysis - Slow Speed Technology
- Turning Speed Detection
- Laser Speed Detection
- Bump Tests
- Bump Test Equipment Off
- Bump Test Equipment Running
- Coast Down Peak Hold
- Coast Down Peak and Phase
- Rotor Bar Test Motor Current
- Order Tracking
- Synchronous Analysis
- Synchronous Analysis and Synchronous Averaging
- Orbit Plot
- Cross Channel Amplitude/Phase
- Collect data using Manual Analyze
- Listen to live vibration data in Analyze
- Redo a measurement
- Store data to a route or a job
- Review collected data
- Print an Analyze plot to AMS Machinery Manager
- Print a plot to a memory card
- Reset Analyze defaults
- Advanced Transient
- ODS/Modal
- ODS/Modal overview
- Manage jobs
- Sensors and inputs
- Tachometers
- Set up the plots
- Set up the job
- Collect ODS/Modal data
- Display the data for a measurement point
- Print an ODS/Modal plot to AMS Machinery Manager
- Print an ODS/Modal plot to a memory card
- Balance
- Balance overview
- Manage jobs
- Job Setup
- Sensor Setup
- Measurement Plane Setup
- Weight Plane Setup
- Acquire Data
- Balance correction
- Trim run
- One-run balance job
- Notes
- Balance summary reports
- Review balance data
- Manually enter balance job data
- Calculator Mode
- Determine another location to place weights
- Combine multiple weights on a rotor
- Calculate a new balance solution to use only the available weights
- Calculate weight placement using static and couple components
- Estimate trial weights
- Calculate weight location around the outside rotor circumference
- Calculate new balance solution to use only available locations and weights
- Amplification Factor
- Convert magnitude or frequency values to a different measurement unit
- Tips and additional information
- Balance accessories
- Technical specifications
- Glossary
- Index
Option Description
Off The analyzer does not use the CSI 2140 Four-Channel Input Adapter or external
multiplexer. The analyzer acquires all data through the same channel, and you
must manually start and accept each measurement.
On The CSI 2140 Four-Channel Input Adapter controls software that switches
between channels. The analyzer acquires all data on channels A to D, and you must
specify the input channel for each measurement point. You must manually start
and accept each measurement reading. The default is On.
Auto The CSI 2140 Four-Channel Input Adapter controls software switching between
channels. The analyzer acquires all data on channels A to D, and you must specify
the input channel for each measurement point. After you start the first reading,
the analyzer acquires and accepts each measurement when the value is good for
three consecutive averages (stable). The analyzer advances to the next step.
Ext An external multiplexer is used. The analyzer acquires all data on channels 1 to 8,
and you must specify the input channel for each measurement. You must
manually start and accept each measurement reading.
5. Press Enter to select the option.
6.
Press Enter.
9.4.6 Set up the bandwidth
You can set the bandwidth (tracking filter) to attenuate all frequency components except
the desired 1x turning speed peak. A narrow bandwidth filter, with a low numerical value,
attenuates frequency components close to the equipment turning speed. A narrow filter
requires more time to take a measurement. The bandwidth of the filter is equal to:
(the frequency of the equipment turning speed peak) X (the bandwidth parameter)
For example, if the equipment speed is 1,800 RPM and the bandwidth parameter is 0.10,
the filter bandwidth is 180 RPM or +/- 90 RPM. Frequency components are not attenuated
between 1,710 and1,890 RPM.
Note
This is available only in Advanced Balance mode.
Procedure
1.
From the Balance main menu, press F3 Job Setup.
2. In Basic Balance mode, press F12 Sensor Setup. In Advanced Balance mode, Enter > F6
Sensor Setup.
3. Press F10 Enter Bandwidth.
4. Enter a value between 0.04 and 0.5.
The default is 0.1.
5. Press Enter.
Balance
201
DRAFT