User's Manual
Table Of Contents
- Home
- Contents
- CSI 2140 Machinery Health Analyzer
- Introduction to the analyzer
- Transfer files with CSI 2140
- AMS Machinery Manager Data Transfer
- AMS Machinery Manager Standalone Data Transfer application
- Communication setup
- Routes and jobs
- Load a route from AMS Machinery Manager into the analyzer
- Load multiple routes from AMS Machinery Manager to the analyzer
- Load a Balance job from AMS Machinery Manager into the analyzer
- Dump a job from the analyzer to AMS Machinery Manager
- Dump a route from the analyzer to AMS Machinery Manager
- Dump a route or job from the analyzer to a folder on a computer
- Analyzer firmware and programs
- Screen captures
- Splash screens
- Printing
- Route
- Route overview
- Manage routes
- Set data collection and display parameters
- Set the plot type for collected data
- Enable or disable Point Advance to automatically move to the next measurement point
- Set High Frequency Detection averages
- Set the route data storage mode
- Set the overlap
- Set the plot type for live data
- Set the overall mode
- Set the integrate mode
- Enable or disable multi-channel group data collection
- Display a summary of data collected for grouped measurement points
- View or hide warning alarms on the Route Data Collection screen
- Restore default values for route data collection and display parameters
- Override the sensor setup for a route
- Enter new speed or load for a measurement point
- Tachometers
- Multiple inputs and measurements
- Collect route data
- Notes
- Plot data
- Run Analyze to collect data for a route measurement point
- View the measurement point setup and history
- Route reports
- Plots
- Analyze and Advanced Analyze
- Analyze overview
- Manage jobs
- Job Setup
- View all saved Analyze jobs
- Create an Analyze job
- Open a saved Analyze job
- Change the job ID
- Edit the equipment ID and description in a job
- Edit the measurement ID and description in a job
- Add a measurement
- Delete a measurement
- Delete data from the current measurement point
- Save a job to equipment in a route
- Set display parameters
- Multi-input measurements
- Sensors and inputs
- Tachometers
- Common data collection parameters
- Collecting data using an Analysis Expert
- Recommended uses of Analysis Experts
- Enable or disable the help text in the Analysis Experts
- High Frequency Analysis
- High Resolution Analysis
- Bearing/Gear Analysis - PeakVue
- Low Frequency Analysis - Slow Speed Technology
- Turning Speed Detection
- Laser Speed Detection
- Bump Tests
- Bump Test Equipment Off
- Bump Test Equipment Running
- Coast Down Peak Hold
- Coast Down Peak and Phase
- Rotor Bar Test Motor Current
- Order Tracking
- Synchronous Analysis
- Synchronous Analysis and Synchronous Averaging
- Orbit Plot
- Cross Channel Amplitude/Phase
- Collect data using Manual Analyze
- Listen to live vibration data in Analyze
- Redo a measurement
- Store data to a route or a job
- Review collected data
- Print an Analyze plot to AMS Machinery Manager
- Print a plot to a memory card
- Reset Analyze defaults
- Advanced Transient
- ODS/Modal
- ODS/Modal overview
- Manage jobs
- Sensors and inputs
- Tachometers
- Set up the plots
- Set up the job
- Collect ODS/Modal data
- Display the data for a measurement point
- Print an ODS/Modal plot to AMS Machinery Manager
- Print an ODS/Modal plot to a memory card
- Balance
- Balance overview
- Manage jobs
- Job Setup
- Sensor Setup
- Measurement Plane Setup
- Weight Plane Setup
- Acquire Data
- Balance correction
- Trim run
- One-run balance job
- Notes
- Balance summary reports
- Review balance data
- Manually enter balance job data
- Calculator Mode
- Determine another location to place weights
- Combine multiple weights on a rotor
- Calculate a new balance solution to use only the available weights
- Calculate weight placement using static and couple components
- Estimate trial weights
- Calculate weight location around the outside rotor circumference
- Calculate new balance solution to use only available locations and weights
- Amplification Factor
- Convert magnitude or frequency values to a different measurement unit
- Tips and additional information
- Balance accessories
- Technical specifications
- Glossary
- Index
Option Description
F7 More Experts View additional Analysis Expert measurements.
F8 Review Data View previously collected data.
F9 Job Setup Create, edit, or delete Analyze jobs. This option does not
appear if you opened Analyze from a route.
F10 Low Frequency Analysis - SST Detect problems with low-speed equipment, such as below 10
Hz.
F11 Turning Speed Detection Determine the turning speed of a shaft.
F12 Laser Speed Detection Determine the turning speed of a shaft using the CSI 430
Speedvue sensor.
ALT2 keys
Option Description
F1 Intentionally blank.
F2 Intentionally blank.
F3 Sensor Setup Set up the sensor parameters for each input. This includes the
sensor type, sensitivity, power, signal coupling, and
accelerometer configuration.
F4 Set Overlap Set the amount that each new average overlaps the previous
average. The default value of 67 percent should be acceptable
for measurements. A higher percent reduces the data
collection time.
F5 Live Display Setup Set the data that should display during acquisition. This option
is available for only spectrum data collection.
F6 Set Calib Factors View or change the calibration factors. Contact technical
support for the required password.
F7 Exit Analyze Close Analyze and display the Home screen.
F8 Intentionally blank.
F9 Connect For Transfer Connect to AMS Machinery Manager to transfer job files. This
option does not appear if you opened Analyze from a route.
F10 Expert Help Enable or disable the help text in the Analysis Expert
measurements. This does not affect the Help key.
F11 Intentionally blank.
F12 Reset Analyze Set Analyze or Advanced Analyze to the default settings.
6.1.3 Analyze and Advanced Analyze
Two options are available for Analyze: Analyze (Basic) and Advanced Analyze. The options are
the same, except Advanced Analyze lets you do two and four-channel measurements.
Analyze and Advanced Analyze
90
DRAFT